Test Access Points
network jump enabling undetectable data monitoring. Also known as: TAP
See Also: Network Monitoring, Network Taps, Aggregator Taps
-
Product
T8730 AIR FLOW TESTER UNIVERSAL
-
T8730 was designed for the precise task of measuring flows on parts such as filters (medicinal, diesel or petrol), tubes, nozzles, openings, valves, etc…Other than the classic flow measurement, the tool also has other ways of making it as versatile as possible in its category: ascent and descent ramps, opening tests and burst testing.Another separate function is the "continuous measurement", i.e. a test with infinite times allowing adjustment of the taps and part repairs in real time.The tool also avails of an intelligent pressure adjustment, which uses the automatic pressure regulator to continuously adjust the test pressure based on the variation in load loss, to ensure the reading is as stable and repetitive as possible.
-
Product
Capacitance And Tan Delta Test
Bushing Tap Adapter Kit
-
Bushing Tap Adapter Kit is designed to perform Capacitance and Tan Delta tests on power transformer bushings The kit can b e used with the following ISA Test Set STS 5000 TD 5000 STS 4000 TD 5000 TDX 5000.
-
Product
Transformer Turns Ratio Testers
-
Transformer turns ratio testers from TRT series are DV Power instruments mainly designed for the measurement of power transformer turns ratio. Also, they measure transformer excitation current and phase shift. Special tests, such as automatic vector group detection and magnetic balance, can be performed on three-phase transformers and three-phase autotransformers.All models, except TRT03 series, have a built-in true three-phase power source, which is necessary for testing turns ratio of transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.DV Power turns ratio testers can output various test voltages for different applications. From the extremely low test voltage of 1 V AC that enables turns ratio verification of the majority of current transformers, up to the highest test voltage of 500 V AC that provides the most accurate turns ratio testing of power transformers used in power generation and transmission. By using the external booster, test voltage increases up to 5 kV AC in order to successfully test capacitive voltage transformers.All DV Power turns ratio testers have a built-in tap changer control unit. Because of that, it is possible to control the on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, the instrument and included DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option significantly facilitates and shortens the turns ratio testing time.TRT turns ratio testers use the same set of cables as three-phase winding ohmmeter & tap changer analyzers from the TWA series. Consequently, it enables one-time cable setup for performing eight tests:turns ratioexcitation currentphase anglemagnetic balancevector group detectionwinding resistanceon-load tap changer DVtestand demagnetization.
-
Product
Complete TAP Signal Isolation for Corelis Boundary-Scan Controllers
ScanTAP IsoPod
-
The Corelis ScanTAP IsoPod™ is an add-on accessory that provides a galvanic isolation barrier between the target system and the boundary-scan (JTAG) controller hardware. While the Corelis boundary-scan controllers are highly robust and reliable, the complete electrical isolation helps prevent damage to the controller from harsh electrical environments where over-voltage and over-current can damage components.This Corelis ScanTAP IsoPod was designed to add an additional layer of protection with minimal cost and effort. Open the box and plug it in; everything just works.
-
Product
High Speed Device & Flash Programmer
JT 2147 QuadPOD
-
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/10) or industrial (/13) variants. The /13 variant includes a SCSI cable splitter to allow system integrators to use flat ribbon cables into the transceiver itself which often simplifies fixture building.A fixture-embedded variant of the JT 2147 is available as part reference JT 2147/FXT. This unit integrates the function of the transceiver and four pod onto a single assembly. This variant can also support 64 DIOS channels and SCIL functions (see more images below for a picture of the JT 2147/FXT).
-
Product
ABex Terminal Module for JTAG Technologies JT 37x7 BSCAN Cards
ABex TM-JT37x7
-
The ABex TM-JT37x7 is an ABex terminal module for the JTAG Technologies Boundary Scan Controller PXI/PXIe JT 37×7. In combination with the JT 2147/ABex from JTAG Technologies it integrates the POD functionality into the module.In combination with the PXI/PXIe JT 37×7 and the JT 2147/ABex it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
Product
RF Taps
-
Praxsym’s RF Taps afford access to a cable system for monitoring function and performance without interrupting service. The taps also cause minimal insertion loss when the coupled port is open, as in normal system operation. Like all Praxsym products, these high-quality devices have honest specifications, and are well-documented over the bands they are designed for.
-
Product
Mini Load Column Load Cell Compression Only with Mounting
MLC SERIES
-
The MLC Series is our miniature high capacity compression only load cell/force sensor, featuring low profile compact size for a wide range of portable and dedicated applications up to 30,000 lb The load diameter is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. The MLCs are designed to be mounted in a shallow machined flat pocket or smooth flat surface, either free or fastened via a bottom 6-32 tapped hole. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
Product
Force Sensors
-
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
Product
Three-Phase Transformer Winding Resistance Meters
TWA Advanced Series
-
TWA Advanced series is the latest DV Power solution for three-phase transformer winding resistance measurement and tap changer analysis. They are capable of testing six transformer windings with a single cable connection, as well as three-phase automatic transformer demagnetization. It has the option of the automated test mode, where the instrument operates the tap changer without operator input (minimizing the risk of human error) and records winding resistance results based on pre-selected stabilization criteria.The unique DVtest method of tap changer analysis enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, together with the measurement of tap changer motor current which detects motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or simultaneously on three phases. It can also be performed together with the winding resistance test in all tap positions.A unique advantage of TWA Advanced instruments is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer connected in a YN configuration. This can significantly speed up the testing– for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.TWA500 is equipped with a large 10.1” graphical touch-screen display, while TWA400 has a 7” graphical touch-screen display. Besides making the interface much more user-friendly compared to older winding ohmmeters, it also enables certain test options that were previously available only with DV-Win software. The most important among them are DVtest, tap changer motor current measurement, “Heat Run” test, test templates, and automatic test mode.
-
Product
Mixed Signal JTAG Tester
JT 5705
-
The JT 5705 series offer a unique combination of JTAG TAP controller (tester) interfaces plus digital and analog I/O in compact desktop package.Use the ‘mixed-signal’ features to measure power supplies, clock frequencies or test DACs and ADCs. Add your own capability through use of CoreCommander FPGA our generic bridge/translator system.
-
Product
Pipeline & Cable Locator
STC-PCL 1101
-
Shanghai Stone Communication tech Co., Ltd
STC-PCL1101 Pipeline & Cable Locator consists of a Transmitter and a Receiver, used in the underground utilities route locating, the depth measuring and long distance tracing. We adopted multicoil electromagnetism technology on this Pipeline & Cable Locator, enhanced the pipeline localization to decide the depth precision and the goal pipeline recognition capability, also could accurately carry on tracing and the localization in the pipeline crowded complex region to the goal pipeline. Thus it is widely used in the telecommunication, electric, tap water, natural gas, physical prospecting, town planning and so on.. STC-PCL1101 has many optional accessories, thus increased their use, and expanded their application scope.
-
Product
Phoenix Camera Link Frame Grabber (D48-PE4H)
AS-PHX-D48CL-PE4H
-
Phoenix-D48CL x4is a PCI Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
Product
CL PX4 SE Frame Grabber
Xcelera-CL PX4 SE
Frame Grabber
The X64 Xcelera-CL PX4 SE is a highly versatile PCIe frame grabber capable for one Camera Link™ Base, Medium, or Full camera and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 SE an ideal solution to a wide variety of cost-sensitive applications.
-
Product
Temperature Sensors
TT420
-
Features • 2-wire, loop-powered 4-20mA analog output • Attachment probe, sensor, and 2-wire 4-20 mA signal conditioner • Compatible with PLCs, meters, and data acquisition systems • No user calibration • TT420Z 1/4" stainless steel probe • TT420S 1/4-28 threaded stud – screws into any 1/4-28 tap • TT420F mounts onto any flat surface • UL listed, Intrinsically Safe (IS) • Class I, (C, D) and Class II, (E, F, G)
-
Product
Averaging Pilot Tubes
-
Meriam manufactures the widest range of Averaging Pitot Tubes for gases, liquids and steam with bi-directional flow capability. Under the Accutube brand name, there are four standard models; Inline, Insertion, Flanged and Wet Tap which can provide a flow solution for your toughest applications. To provide the complete flow solution that meets your specific needs, we can provide DP or Multivariable transmitters from the brand of your choice, or we will recommend the best fit for your application. These transmitters can be installed on the Accutube and configured to your specific flow requirements here at Meriam by qualified technicians, reducing your expense and time .
-
Product
Turns Ratio Testers
TRT Standard Series
-
When it comes to choosing a transformer turns ratio tester, TRT Standard series offers some of the most advanced instruments with LCD display out in the market. Each model measures transformer excitation current and phase shift performs automatic vector group detection and magnetic balance on three-phase transformers and three-phase autotransformers. Furthermore, they have a built-in true three-phase power source. Because of that, TRT Standard instruments can test transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.The instruments can output test voltages from 1 V AC to 250 V AC, depending on the chosen model. High test voltage of 250 V AC provides more accurate turns ratio testing compared to other turns ratio testers on the market and extremely low test voltage of 1 V AC enables turns ratio verification of current transformers.TRT Standard series consists of:TRT03 Models (TRT03A, TRT03B, TRT03C) – single-phase voltage up to 100 VTRT3x Models (TRT30A, TRT30B, TRT30C, TRT33A, TRT33B, TRT33C) – single and true three-phase voltage up to 100 VTRT63 Models (TRT63A, TRT63B, TRT63C) – single and true three-phase voltage up to 250 VMore about models differences can be found under the downloads tab, in brochures and comparison sheets.A user can create test templates using the DV Win software and store them in the PC’s memory for later use when in the field.TRT Standard series models have a built-in tap changer control unit. Consequently, it enables remote control of an on-load tap changer (OLTC) directly from the tester. In order to make the most out of this feature, the DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions and saving results. This option, especially in combination with test templates, significantly facilitates and shortens the turns ratio testing time.
-
Product
ITA, 9075, 75 Module, Triple Tier
410104258
ITA
The 75 Module, triple tier ITA is rugged and perfect for high I/O test and measurement applications. This ITA is made of steel to prevent any deflection caused by the high insertion forces from the available I/O. The added tapped holes on the back of the frame allow you to attach an enclosure or custom fixture.
-
Product
Versatile Test Stand
VTS-2100
-
Applied Scientific Instrumentation
*Base is a Breadboard on 25 mm centers tapped for M6 screws with threaded holes for risers for TE/TI-2000, TE-300, IX-71/81, DMI, and MS-2000 stages.*Base feet provide vibration isolation.*Z riser is adjustable on pillar blocks.*Z motion from LS-50, LS-100, or LS-150 linear stage.*Z illumination can use LED, LED and a Condenser (from below), or fiber illumination (from above).*Observation is with a Modular Infinity Microscope.
-
Product
Ultrasonic Flowmeters
-
Clamp-on type sensor easily mountable on existing pipe Suited for a wide range of liquids, for example, deionized water, cooling water, chemical solution, drinking water, sea water, oil, tap water, hot water, industrial water, corrosive liquids. Ultrasonic flowmeter for air is also available
-
Product
Fiber TAPs
-
Profitap fiber TAPs provide secure in-line network access for the monitoring of 1–400 Gbps fiber networks. By splitting the light flowing on the network link, fiber TAPs deliver an exact copy of the data for real-time monitoring and analysis, without disrupting the network. Passive fiber optic TAPs require no power, and therefore introduce no point of failure when deployed in a network.
-
Product
Control Transformers
-
ENTES control transformers ensure the safe operation of measuring devices with 24 VAC supply voltage for electical control panels. Input voltages of Control transformers are either fixed (230 or 400V) or selectable with taps (400;230+15-15).
-
Product
Air Core Electric Arc Furnace Reactors
-
Arc Furnace Reactors are serially connected reactors that are installed in the supply systems of arc furnace transformers to stabilize arc and limit the unstable arc furnace current and voltage drop which optimize their melting process. These buffer reactors are connected in series to the primary side of the furnace transformer. Typically these reactors are tapped coils and manufactured as per customer'stap requirements.
-
Product
Phoenix Camera Link Frame Grabber (D24-PE1)
AS-PHX-D24CL-PE1
-
Phoenix-D24CL is a PCI Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of Base configuration, i.e. single 8- to 16-bit data, through 8-bit RGB, to dual tap 12-bit sources.
-
Product
ABex Terminal Module for Göpel 1149Cx BSCAN Cards
ABex TM-1149Cx
-
The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
Product
Free Data Monitoring Software For EZ-Tap™, EZ-Pro™, And Versa-Tap™ Passive Tap Modules
-
Stratus Engineering's EZ-View™ data monitoring program controls communication and data collection parameters and displays time-tagged communication data and handshaking events in an easy-to-use scrolling display window.
-
Product
RF Signal Detector/Wireless Camera Detector
SH-055SRV / 10127
-
This "Wireless Camera Detector / RF Signal Detector / 2G Mobile Phone Detector" can detect the popular wireless CCTV camera, wireless phone, wireless tap and Cell phone from 50 MHz ~ 6.0 GHz.
-
Product
M-TAP Fiber Test Tap
-
The Maxcom Fiber Tap (M-TAP) is a portable optical test tool designed to minimize customer downtime. Two Splitters/Taps One Portable Device 80/20 split ratio 50/50 split ratio
-
Product
Digital/Analog/Frequency Measurement Module
JT 2149/DAF
-
The JT 2149/DAF is a compact, mixed-signal (Digital/Analog/Frequency) measurement module for use in JTAG Technologies’ widely-used JT 2147 (QuadPod) signal conditioning interface. The DAF module has been designed to replace a regular TAP Pod and provides 28 measurement channels plus a clock generator. When connected to a circuit board via edge connector or test fixture/jig test pins, the module enhances standard digital boundary-scan tests by enabling a series of analog and frequency measurements to be made.
-
Product
48" Stacking Banana Plug Test Leads
146-P
-
These test leads feature stacking banana plug jacks, with extended 48" length. These are great for establishing connections to diagnostic test points, while allowing the connection to be tapped with other instruments...2 way connections. These feature high flexibility wire and standard 4mm size banana jacks. You will receive one red test lead and one black test lead. These test leads are compatible with Electronic Specialties 146 and 147 test lead kits.
