Product

Heavy Load Ball Screw with Caged Ball Structur

HBN

-

THK America, Inc.

HBN - THK America, Inc.

Heavy Load Ball Screw with Caged Ball Structure. Heavy load ball screws with the caged ball structure (HBN model) drastically improve the rated load compared to the conventional products by utilizing the optimum internal structure for use in heavy load condition. In this model, the caged ball structure is adopted between balls to eliminate collisions and mutual frictions of the balls and improve the lubricant maintenance. This modification brings about a longer lifetime under heavy load conditions.

Product

DC Electronic Load

Model - KM-mPD-501

-

Kusam Electrical Industries Limited

Model - KM-mPD-501 - Kusam Electrical Industries Limited

KM-mPD-501 DC electronic load mainly focuses on the testing of power circuit on PCB. KM-mPD-501 offers a solution for function test of Switch step up, Stepdown, Regulators and Driver IC . Engineer puts components, such as CPU, DSP, FPGA; etc on a PCB after the power circuit has been tested. It’s not complete to use a meter to measure the voltage. KM-mPD-501 offers engineer OVP, OCP and OPP functions that help engineer know the value of overload current . On the other hand, engineer can use a programmable DC power supply (mPP series) to offer external power and connect PCB’s output to KM-mPD-501. Then engineer can easily get output watt, figure out the efficiency of power circuit and check if inductances, capacitances and resistances perfectly work with the power circuit. KM-mPD-501 not only offers loading emulation of current but also provides OVP and OPP. User can use these functions to test solar power battery, rechargeable battery and motor driver. In school laboratory, KM-mPD-501 helps students do experiment on power circuit, linear circuit and driver circuit.

Product

WaveLink ProBus2 Platform/Cable Assembly for 4-8 GHz WaveLink Amplifiers.

WL-PBUS2

-

Teledyne LeCroy

WL-PBUS2 - Teledyne LeCroy

- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead

Product

Off-Set Kelvin Test Sockets

-

UWE Electronics

UWE Electronics

This is an innovative and robust contact technology for making Kelvin contact to 0.5mm pitch QFNs. The contact uses a tip that is angled to one side, matched to an orientation that's flat on the tip. Two such contacts placed in opposition will touch the pad within 0.125mm. And because the tip is offset, the probe diameter is a robust 0.39mm and the load board pad pitch remains 0.5mm.

Product

Mid Energy Counters

-

Algodue elettronica

Algodue elettronica

UEM1P5-4D R for RS485 Modbus RTU/ASCII communicationUEM1P5-D M for M-Bus communicationUEM1P5-4D E for Ethernet (Modbus TCP) communicationFor 1 or 5A CTProgrammable CT ratioFully bi-directional four quadrants measurements for all energies and powersFor 3 / 4 wire networks with balanced or unbalanced load (UEM1P5-4D R and UEM1P5-4D E only for 4 wire networks)Class B according to EN 50470-3S0 output for energy pulse emissionAvailable with MID certification

Product

Cold Bend Testing Machine

QualiBend Series

-

Qualitest International Inc.

QualiBend Series - Qualitest International Inc.

The Cold Bend Testing Machine - QualiBend series are used for bending of metallic materials such as metal rods, planks and steel screw threads. The machines operate with a hydraulic loading system to adjust the distance of the cold-bending press roll to drive the rod in both directions making the cold bending press roll forward and back.

Product

50W to 150W - Single Output

VS-E Series

-

TDK-Lambda Corp.

VS-E Series - TDK-Lambda Corp.

*High efficiency*Low standby power*100% load at 50°C*Five year warranty

Product

Power Cord Bending Tester

SW-6

-

Lisun Electronics Inc.

SW-6 - Lisun Electronics Inc.

SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ   12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.

Product

Active Voltage Rail Probe

-

Teledyne LeCroy

Teledyne LeCroy

Voltage rail probes are designed specifically to probe a 50 Ohm DC power/voltage rail. The probe has large built-in offset, low attenuation (noise), and high DC input impedance. Built-in offset and low attenuation permit the power/voltage rail to be offset in the oscilloscope by its mean DC voltage with high oscilloscope gain (sensitivity) to achieve a noise-free view of small signal variations. The high DC input impedance eliminates loading of the DC rail.

Product

High Power DC Electronic Load

IT8800 Series

-

I-TECH Electronic Co., Ltd

IT8800 Series - I-TECH Electronic Co., Ltd

IT8800 series has wide power range 150W~10KW, voltage and current measurement speed up to 50KHZ, resolution up to 0.1mV/0.01mA, adjustable measurement current rising speed 0.001A/us~2.5A/us, built-in RS232/GPIB/USB interface. IT8800 series has wide application fields because of its high performance products, it has been applied to LED lighting, aerospace, automotive electronics and other fields.

Product

VPX 6U Load Board Conduction Cooled

1940000376-0000R

-

ELMA Electronic, Inc.

1940000376-0000R - ELMA Electronic, Inc.

6U VPX Load Board, 6U x 160mm, conduction-cooled.

Product

Inductive Load Banks

L-Series

-

Hilkar

L-Series - Hilkar

L-series inductive load banks are devices which contain inductive loads, apply the load to an electrical power source and dissipate the reactive power of the electrical source. L-series load banks are designed for portable and fixed applications. Hilkar brand L-series load banks have robust design and are specifically designed for corrosive environments. Load banks can be controlled via local, remote, wireless remote or automatic control systems.

Product

Network Analyzer

DPNA-6G AXIe

-

Holding Informtest

DPNA-6G AXIe - Holding Informtest

The AXI DPNA-6G module is the world's first network analyzer in the form factor of the AXIe-1 module, as well as the first Russian device that meets the AXIe-1 standard. In the mode of the network parameters meter, the AXI DPNA-6G module measures the vector values ​​of the network parameters on two ports: transmission coefficients (S12, S21) and reflection (S11, S22). At the same time, all necessary types of calibrations are supported: one- and two-port short-circuit, XX, matched load, transmission normalization. The software supports the import of third party calibration standard parameters. In the measuring receiver mode, the module provides:*generation of a harmonic signal (frequency synthesizer);*spectrum analyzer and power level in a given band;*measuring the frequency of a known signal;*measurement of analog modulation parameters;*phase noise measurement.

Product

Relay I/O Modules

XTA Series

-

Acromag, Inc.

XTA Series - Acromag, Inc.

These modules are intended for use with BusWorks XT Series discrete I/O or other digital output modules for the purpose of driving high energy loads.

Product

Shaft Type Load Cell

KS

-

JFE Advantech Co., Ltd.

KS - JFE Advantech Co., Ltd.

Shaft Type Load Cell

Product

NI STS

-

RF Test and Measurement Solutions, LLC

RF Test and Measurement Solutions, LLC

RFTMS is a leader in configuring systems to meet your needs, as well as designing load board, writing SW, and integrating the final solution. We do this for wafer test, packaged parts, and modules. RFTMS can address any level of integration that your parts employ, from a single functional block, i.e., Power Amplifier (PA) to System-on-a-Chip (SOIC). We test all sorts of RFICs.

Product

Clamping Voltage Tester

MIG0603CLV2

-

EMC Partner AG

MIG0603CLV2 - EMC Partner AG

The MIG0603CLV2 is a generator for clamping voltage testing of varistors. It has circuits with four different source impedances and up to 15 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 500A which is maintained over the entire load range.

Product

Test Contactor

RF Scrub

-

Cohu, Inc.

RF Scrub - Cohu, Inc.

RF Scrub™ Test Contactor’s innovative design combines an extremely short signal path (0.90mm test height) with high wear resistance pins that can operate in a wide temperature range.The RF Scrub Test Contactor’s long-life, elastomer free design and easy field maintainability makes it an optimal solution for testing of high-performance devices.The RF Scrub design minimizes load board wear and with the unique pin base material and plating, the cleaning intervals can last up to 100,000 cycles.

Product

120 A High Voltage 50 Ω Pulse Generator

TLP-12010C

-

High Power Pulse Instruments GmbH

TLP-12010C - High Power Pulse Instruments GmbH

- High pulse output current up to 120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical rise time 100 ps (0 A to 40 A) and 300 ps in high-current mode (0 A to 120 A)- Wafer, package and system level TLP, VF-TLP and HMM testing- Up to 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 USB programmable pulse rise times: 100 ps to 50 ns (custom selectable)- 8 (optional 9) programmable pulse widths: 0.5 ns (optional), 1 ns to 100 ns (0 A to 40 A), 1 built-in pulse width: 100 ns (>40 A)- The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0 A to 40 A)- Optional external pulse width extensions from 5 ns to 500 ns (>40 A to 120 A)using the external pulse width extender TLP-12012A6- Built-in pulse reflection suppression- Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses- Efficient sofware for system control and waveform data management- The sofware can control automatic probers for fast measurements of complete wafers- Combines TLP-12010A and TLP-4010C into one system- Can be operated together with TLP-12012A6 and TLP-3011C pulse width extenders- Integrated interlock safety shut-down- Industrial isolated and EMI/ESD protected USB control interface

Product

Multi-Channel, Programmable Current Source

CS-48-100

-

Hypres, Inc.

CS-48-100 - Hypres, Inc.

The Model CS-48-100 is a multi-channel, programmable current source. Developed for both semiconductor and digital superconductor electronics, it is computer-controlled and features 48 low noise current source outputs. Each source output has the capability to both set and read back currents and can be set to a zero current high Z mute state. Each of the 48 sources are optically coupled for control and are sourced from their own secondary winding for complete galvanic isolation. The device consumes a maximum of only 80 W and handles a maximum load current of 4.8 A total over all outputs. Operating over a range of 0-100 mA on each channel, the device features accuracy of +/-25 ?A. The mute state can be set thru a rear panel interlock or from the front panel button for maximum circuit protection. The unit can be mounted in a standard-sized rack.

Product

48V / 300 Amp Load

BD18-48P-24/12

-

Manatronics Pty Ltd

BD18-48P-24/12 - Manatronics Pty Ltd

For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.

Product

Automated Soxhlet Extractor

Soxtec™ 8000

-

FOSS A/S

Soxtec™ 8000 - FOSS A/S

The Soxtec 8000 extraction unit is a fully automated system for fast and safe extraction of soluble matter from a wide range of matrices. It performs the four extraction steps boiling, rinsing, solvent recovery and auto-shut down, fully unattended. Just load, start and walk away. The Soxtec 8000 is specially designed to ensure the highest possible throughput and safety.Parameters: Crude fat, Total fat and Extractable matterSample types: Fat in food and feed. Extractable matter in textile, paper pulp, plastics, rubber etc. PCB and PAH in soil and sludge (the Soxtec is a preparatory step to GC-MS).