Systems
are interconnected groups of purpose.
See Also: Equipment, Test Systems, System Integrators, System Test
-
Product
ICAP/4Rx
-
Your prescription for reducing the complexity of analog & mixed-signal design. Provides the most powerful, low-cost simulation solution on the market. Includes hierarchical and configurable schematic entry system (SpiceNet) and full simulation power, less special applications and multi-run analyses (Monte carlo, worst case, etc.).
-
Product
Automatic Software Testing
Conformiq
-
Instead of using test cases, Conformiq users have a model, which describes the System Under Test, or the product they want to test. From the model, Conformiq products use highly intelligent algorithms to automatically determine the necessary tests and test data, and automatically generate scripts for automated execution.
-
Product
Expert On Alert
-
Expert-on-Alert provides centralized monitoring of locomotive health status and performance in real time. Locomotives transmit data to the Wabtec monitoring and diagnostic center, where a team of experts analyzes control system status and performance data. This enables Wabtec to determine the root cause of failures while locomotives are in-transit, providing timely maintenance and repair recommendations.
-
Product
Logic Analyzer Probes
FS2354 & FS2355
-
The FS2354 and FS2355 are logic analyzer probes used to test DDR3 SO-DIMM memory modules. When used with the triggering and analysis capabilities of Keysight’s Logic Analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR3 SO-DIMM systems.
-
Product
Digital Ultrasonic Maintenance System
VPE-2000
-
The Superior AccuTrak VPE-2000 is the first digitally controlled ultrasonic detector. Like two instruments in one it uses two independent sensors supported by separate electronic circuits configured specifically to their own sensor. This assures optimum sound clarity and frequency response. When switching between the airborne and contact sensors all settings are retained in memory! Digital LED meters let you establish baselines, perform trending, and accurately repeat these tests better than older more expensive analog instruments.
-
Product
System Status Monitoring Software
CHM
-
The R&S®CHM system status monitoring software is an integrated, system-specific solution for continuous monitoring of key system parameters in systems from Rohde & Schwarz. It monitors devices and system components fully automatically, outputs warnings and alarms to operators if system components approach or reach critical operating states, and assists maintenance personnel in fault diagnosis..An extensive set of analysis tools, such as the visualization of measured values in time-sequence charts, helps system administrators to carry out maintenance work and identify errors.
-
Product
LTE RRM Test System
T4010S
Test System
The T4020S LTE RRM tester is the Keysight platform for LTE RRM conformance testing of LTE UEs. T4020S belongs to the Keysight LTE product family and, as the other LTE T4000S test platforms, is based on the T2010A LTE Wireless Communications Test Set.
-
Product
16-bit, 200KHz, 4SE/2DIFF Isolated Analog Input Board
APCI-3016-4
-
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
-
Product
CAMI® Broadband AM Isocouplers
-
LBA Technology’s CAMI® series of new-concept low, medium, and high power broadband isolators are the modern way to mount additional antennas on “hot” AM towers. These broadband colocation systems offer a simple, economical solution to take full advantage of existing vertical real estate. The LBA CAMI® isocoupler family supports any combination of RF carriers from DC to 2700 MHz or more, and conservative RF power levels to 40,000 watts at FM.
-
Product
PXI-7853, Virtex-5 LX85 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780341-01
Multifunction Reconfigurable I/O
Virtex-5 LX85 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7853 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7853 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
On-Site Oil Analyzer
MiniLab 23
-
With two simple tests, the MiniLab 23 delivers on-site oil analysis, providing immediate actionable results, saving time and reducing costs. Highlights of this system include:*One product, delivering lab-quality analysis outside of the lab*Simplified workflow for the non-expert user, no chemist required *Simplified operation, data reporting and report interpretation via the TruVu 360 Diagnostic Sets with recommended actions.
-
Product
Custom Embedded and Hardware Solutions
-
High performance, end to end hardware solutions and system integration capabilities that deliver sophisticated customized solutions and lifecycle management from inception to implementation across the medical imaging and telecommunications industries
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 2 Channels, High Voltage Outputs
M2P.6571-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
All-In-One Touch Computer
UTC-115K
-
15.6" All-in-One Touch Computer with Intel® Core™ i3/ N97 Processor. Slimmer and Lighter design. Low power and fanless system design. Built-in Intel® N97/i3-N305.
-
Product
Flexible Automatic Measuring System Release
FAMS-R5
-
FAMS-R5 uses the system with high-speed communication, FAMS High-Speed Link2, to share data with each unit.Sensors can be directly connected to the measurement unit in a laboratory.Simple wiring and highly accurate measurement can be achieved.By adding the MCU that can calculate the control model with MATLAB/Simulink, it also supports the simulation bench.
-
Product
CD/DVD Analyzer
Shuttleplex
-
The ShuttlePlex CDVD Analyzer can be configured to automatically test, save, report, grade, print and export your optical disc data. The unit is designed to provide an efficient, effective, low cost analysis for just about any optical disc production process. The User interface provides a feature set and graphical environment (See Below) similar to those used by Professional Engineers in a Disc Manufacturing Environment. The Unit was designed with Duplicators, Web Disc, Game Designers, Media Distributors and Archivalists in mind. The ShuttlePlex can be purchased in Several configurations; as a stand alone unit, external laptop drive or integrated into a PC based duplication system.
-
Product
9025 Rack Mount
-
VPC rack mountable receivers like the 9025 meet the standards which are essential to support advanced mass interconnect requirements. Connector modules can be intermixed to establish custom interfaces which are ideal for functional and system testing applications.
-
Product
Harmonic/Flicker Analyzer for IEC61000-3-2/3/11/12, IEC61000-4/7/15
KHA3000
-
KHA3000, in addition to the complied standards and features of the KHA1000 (dedicated for single phase), is equipped for the harmonic and flicker compliance test exceeding 16A of the single-phase and three-phase equipment. With this unit alone, you can take highly accurate simultaneous three-phase measurements up to 40A/phase*. Furthermore, the KHA series is compliant with two measurement technique standards, the existing and the latest versions, so you can simply select to take measurements for the latest standard including interharmonics and for the conventional integral multiple harmonics without using any other device. In addition to the real-time display that can be used like an oscilloscope and FFT analyzer, the unit offers the real-time judgment of compliance with standards. Using this unit alone, you can judge test results and prepare result reports without the use of a PC. On top of that, you can easily set up a test system by combining KHA3000 with an AC power supply (PCR-LA Series) and a line impedance network (LIN40MA-PCR-L).
-
Product
16 Channel WDM Mux/DeMux
S-106
-
16CH WDM Mux/DeMux module of FOTS system offers a function of multiplexing or demultiplexing up to 16 channel of WDM signals. This module offers low insertion loss, low crosstalk, and high temperature stability. An internally built-in AWG module functions as 1 X N optical Multi/Demultiplexers. The bi-directional feature of this module is ideal for wide range of applications. In combination with an optionally built-in circulator or C/L-band WDM coupler, this module can be applied to the WDM-PON test. User can easily make his or her test set-ups for FTTX-PON systems, especially for WDM-PON test, by combining this module with other FOTS modules such as SLED Driver, SOA Driver, C+L-FOTS modules such as SLED Driver, SOA Driver, C+L-band ASE source, Wavelingth meter, Transceiver Driver and so on.
-
Product
Fanless Embedded System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q170, HDMI, DVI-D, VGA, 8-CH PoE, 6 USB And 24 VDC
eBOX671-517-FL
-
The eBOX671-517-FL supports 8-port Gigabit PoE and able to work under harsh temperatures. Its eight Gigabit PoE ports allow multiple cabling to cameras and any PoE power device; and, the eBOX671-517-FL is specifically designed for security surveillance, optical inspection, and edge computing applications. This rugged NVR embedded box PC is powered by the 7th/6th generation Intel® Core™ (Kaby Lake/Skylake) or Intel® Celeron® processors with a 35W/65W TDP and comes with Intel® Q170 chipset. The eBOX671-517-FL comes in great expansion possibilities, including a flexible I/O module slot with a wide selection of PCIe Mini modules and four PCI Express Mini Card slots. It also has two front-accessible SIM slots and four SMA-type antenna connectors. For storage, this high performance fanless embedded system has two SATA HDD drive bays with a height of up to 15 mm and one optional mSATA for RAID 0 and 1. Moreover, the embedded device supports two non-ECC 260-pin DDR4 SO-DIMM slots for up to 32GB of system memory.
-
Product
Receiver, G12x, 18 Module, 20" Platform, w/ Ext Handle for Slide Mount (slide kit required)
310104457
Receiver
This G12x Receiver is slide-mounted with a 20” platform that supports up to 180lbs. or up 350 lbs. when used with optional leg kit. The G12x is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull-down for a reliable connection every time. The handle is extended 6" and can be rotated in 90 degree increments. The G12x is rated up to 20,000 cycles.
-
Product
Force Calibrating Machines
-
Morehouse Instrument Company Inc.
Morehouse Universal Calibrating Machines (UCM) are an easy to use, cost-effective, hydraulic force calibration system that lasts for generations. UCMs built in the 1950s are still operating today! The UCM can be used to calibrate both tension and compression instruments in accordance with ASTM E74, ISO 376, and other internationally recognized force standards.
-
Product
Audio Analyzer
BK2110
-
The BaKo BK2110 Audio Analyzer is a 2 channel Digital Signal Processing (DSP) based system so you can analyze a stereo signal from an acoustic device. And because it is DSP based, it can quickly and accurately test high quality digital audio devices. All test items can be measured simultaneously and you can see them in real time or, using the LAN interface, send them to a computer system to analyze.
-
Product
photonHiRES
-
The especially sensitive and high-resolution cameras belonging to the photonHiRES platform are the leading solution when it comes to achieving the highest resolution in industrial machine vision. Even when faced with challenging applications and poor light conditions, the cameras from Photonfocus achieve the best possible results. The robust housings are equipped with an outstanding temperature management system and enable fan-free operation of even large sensors. Moreover, the powerful 10 GigE Vision interface guarantees an optimum data transmission rate and compatibility with a wide range of interfaces.
-
Product
Upgrades and Parts
-
The Lorlin Test Systems Impact Testing Software Upgrade Version 7+® operates under Windows 7/8/10® 64-BIT with a USB 2.0 tester interface is available for Impact and Dataspec Testers.
-
Product
Turnkey or PCI Cards and Software
WinCAT Systems
-
# True fast transient recorder system.# 4, 8 or 16 channel models.# 1 MHZ aggregate 12 bit sampling, resolution equal to 0.024% of full scale.# 13 record lengths, user selected, 132 msec to 1,320 sec in typical 1-2-5x scope progression.# 6 programmable front end gains, user selected, equal to 0.4, 1, 2, 4, 10 and 20 volts full scale.# Software converts digitized voltages to Engineering units.# Digital Triggering, Amplitude and slope, in engineering units from digitized input signals.
-
Product
Variable Optical Attenuator
CARY-VA3301B
-
The CARY-VA3301B handhold variable optical attenuator is used for continuously variableoptical signal attenuation. Since the variable optical attenuator is used in the laser system for the on-line testing, CARY-VA3301B can be used in the digital system of communicationdevices (such as: PHD, SDH) and also can be used in the CATV system testing.
-
Product
Fire Control System
MS 1120
-
PCI Based BTA is used to test FCC System Processor (8086) & Analog Boards. This system consists of a PC-AT, Digital Input / Output (DIO) Board and Analog Input / Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
Product
RF CAPTURE & PLAYBACK SYSTEM
WEIVER 2.0
-
With Weiver 2.0, you can capture worldwide broadcasting standards of DTV (FM, AM, ATSC, DVB-T/H, DVB-T2/S2, DVB-C, DMB, CMMB, DTMB, ISDB-T/B, OpenCable, and ATSC-M/H). Also, you can capture radio broadcasting ATV (NTSC, PAL), RDS, TMC, LTE, and Wifi. Weiver is equipped with a GPS module for accurate location information to evaluate the strength of the RF signal. Basically, you can capture any live signals and then playback wherever and whenever you need to.
-
Product
H(3)TRB & HTGB Test Systems
Test System
SET offers two H(3)TRB and HTGB product lines which differ in the number of test object channels and the range of technical possibilities. The innovative systems are scalable, modular and standardized.
