Filter Results By:
Products
Applications
Manufacturers
-
product
10MHz DDS Sine & Square Wave SIGNAL GENERATOR
SG-10
Model SG-10 architecture is based on the latest advances in DDS technology. Microprocessor control delivers clean and accurate DC to 10MHz waveforms with frequency accuracy of 0.02% and 0.1 Hz frequency resolution.
-
product
UPG-07 - Ultrasonic Precision Gages - Monochrome
UPG-07 Monochrome
PG-07 Series of hand held ultrasonic precision gages are available in 4 models. Our UPG-07 series is the ideal unit to non-destructively test the wall thickness for manufactured parts requiring unprecedented accuracy and resolution. The UPG-07 series utilizes single element transducers and offers a 30 Mhz, square wave pulser, .0001" or 1 micron resolution with the ability to store and re-call 30 unique applications. So if you are measuring light bulbs, plastic bottles, golf clubs, coil steel, thin aluminum, aircraft parts and even pure gold bars, the UPG-07 series is the right choice.
-
product
Demonstration Board
SAMPULSE20x2
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
product
Light-to-Frequency
Light-to-Frequency (LTF) sensors convert measurements of light intensity to a digital form for direct interfacing to a microcontroller. The output of the device is a square wave or pulse stream the frequency of which is linearly proportional to the light intensity. LTF converters are designed for applications such as ambient light measurement, light absorption/reflection in products such as white goods, photographic equipment, colorimetry, chemical analyzers and display contrast controls. They may be used in any system that requires a wide dynamic range, and/or high resolution digital measurement of light intensity.
-
product
Digital Multimeter
7125
Peaceful Thriving Enterprise Co Ltd
This is a low power consumption, high accuracy and stable hand held multi-meter; with special designed IC to support true RMS measurement. It performs measurements of AC/DC voltage, DC current, resistance, diode and square wave output.
-
product
Square Wave Patterns (Ronchi Gratings/Rulings)
Square Wave patterns (Ronchi Gratings/Rulings) have extremely sharp edges. At APPLIED IMAGE, this sharpness is achieved through our unique manufacturing capabilities and processing technologies which produces the sharpest edges available anywhere. Our standard line of Ronchi Gratings is offered on Chrome on Glass (CG) and Photo Paper (RM).The Ronchi rulings are available on other substrate materials such as B270, quartz, BK-7, and White Opal as well as in English frequency metrics (cycles per inch).
-
product
CPCI or PXI DPFS Board
MS 1830
- Configurable Frequency Ranges from 100Hz to 1MHz- Resolution insteps of 0.03Hz- Duty Cycle 50%- Amplitude of the Digital Frequency out : Low – 0.4V max, High – 4.8V min- Rise/Fall Time (for a 15pF Load) is typically 5 ns- Amplitude of the Analog waveform out : Low – 0.4V max, High – 4.8V min- Sinusoidal or Square Wave Output (Configurable)- Differential / Single Ended Output (Configurable)- Frequency on each of the 8 Channels are individually Programmable- Hot Swap Facility for live insertion and removal of the board- Facia plate with Micro Switch Assembly, provided for proper insertion / easy removal of the Board- BNC Connector Interface for Signal Output at the front panel- Each Output Channel is driven by a Cable Driver to drive 8m of Coaxial Cable- Driver interface for Windows XP/VISTA/7 and LINUX OS
-
product
20 MHZ Arbitrary Waveform Generator
F175 AWG
he F175 AWG does not replace our current square wave generator models (F125/165/170/110). It is an arbitrary waveform generator. Its main strength is in producing non-square waves. Of course it is also able to produce square waves but if you only need generate square waves, please look at our other models: F125/165/170/110. We expect to have F175 AWG production boards available in the third quarter of 2009.
-
product
Frequency Doubling Comb Generator
COMBGEN6DIFF
*Differential output - can also provide two separate single ended complementary outputs.*Pulse height of up to +4V peak into 50 ohms, on positive output*Pulse height of up to -4V peak into 50 ohms, on negative output*Rise time < 80pS, FWHM of approximately 120pS*Produces pulse on both edges of input clock, thereby doubling frequency.*Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz.*Usable energy to >10GHz.*Can drive any load, including short, without damage.*Power Requirements: -12V @ 120mA and +24V @ 80mA
-
product
Function Generator
G5100A 50MHz Function / Arbitrary Waveform Generator can create stable, precise, clean and low distortion sine waves by using DDS (Direct Digital Synthesis) Technology. With fast rise and fall times up to 25 MHz for square waves and 200KHz for linear ramp waves , the G5100A also can reach users』 demand on waveforms。
-
product
Rubidium Standard with Optional DDS Signal Generator
1450B
The 1450B outputs can be configured as sine waves or square waves and can provide frequencies of 10MHz, 1MHz, 100kHz, 1pps or optional signal generator outputs. The signal generator outputs use direct digital synthesizer (DDS) technology and are confirurable from 100Hz to 171MHz. The 1450B also includes a 1pps input that can be used to discipline and automatically calibrate the 1450B. The 1pps input signal is typically obtained from an external device like a GPS frequency receiver/antenna. The Novatech GPS1 Smart Antenna with 1pps output is available as an accessory to provide a complete turnkey solution.
-
product
Optical Detector
LG-9200
The LG-9200 is a non-contact type optical detector which emits red visible light and detects the reflected light from the rotating shaft. The reflection mark is used for the detection by affixing it on the rotating shaft. It enables detection at an angle. (reflective mark: HT-011 by Ono Sokki)The LG-9200 has a built-in compact amplifier and outputs the square wave (voltage) after waveform shaping.With a compact and light weight body, performances are upgraded compared to the previous model LG-916.(LG-9200 detection distance: up to 40 mm, response speed: up to 40 m/s)
-
product
Mini Digital Multimeter
HH2103
Basic Accuracy 1.0%. LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 2000KΩ. Diode test. Square Wave Signal Injection
-
product
Synthesized Clock Generator
CG635
Stanford Research Systems, Inc.
The CG635 generates extremely stable square wave clocks between 1 µHz and 2.05 GHz. The instrument''s high frequency resolution, low jitter, fast transition times, and flexible output levels make it ideal for use in the development and testing of virtually any digital component, system or network. Clocks from 1 µHz to 2.05 GHz. Random jitter <1 ps rms. 16 digits of frequency resolution. 80 ps rise and fall times. CMOS, PECL, ECL, LVDS & RS-485. Phase control and time modulation. PRBS for eye-pattern testing. OCXO and rubidium timebase.
-
product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
product
Microwave Comb Generator
*Differential output - can also provide two separate single ended complementary outputs. * Pulse height of up to +4V peak into 50 ohms, on positive output * Pulse height of up to -4V peak into 50 ohms, on negative output * Rise time < 80pS, FWHM of approximately 120pS * Produces pulse on both edges of input clock, thereby doubling frequency. * Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz. * Usable energy to >10GHz. * Can drive any load, including short, without damage. * Power Requirements: -12V @ 120mA and +24V @ 80mA
-
product
VLF test system
BAUR PHG 80 portable
BAUR Prüf- und Messtechnik GmbH
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
product
Compact Multi-use Type Rotary Encoder
RP-432Z
Compact and economical design for general purpose;ideal for OEM applications5 VDC or 12 VDC operationEasy-to-use output signal connector2-phase and zero mark square wave outputsNine output pulse types to select from.
-
product
Component Test
Our innovative multi-function Electrical Component Testers have advanced functions such as voltage power control feed to activate components like radiator fan, headlights, horn, actuators, etc. and the sensor simulator can provide simulation of voltage signals, frequencies, square waves & duty signals with varying intensity to test the feasibility of good sensor signals in comparison to bad ones when troubleshooting vehicle electrical faults.
-
product
Loss Tangent M in Dielectric Oil
TAND220A
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
product
Palm Size Digital Multimeter, Calibrated, 1999 Count, Mean Value, Manual Range, 3.5 Digit
72-7770 CAL DU
The 72-7770 CAL DU from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.
-
product
HV Test bench
It is a deeply customizable test bench which is suitable to generate frequency and amplitude controlled voltage. This test bench could be used for life test or quality test on samples or devices. It can be configured both for sinusoidal test (STANDARD version) and both for square wave or pulse test (TechSQUARE). It includes safety systems for avoiding overload and incorrect use.
-
product
Palm Size Digital Multimeter, Calibrated, 1999 Count, Mean Value, Manual Range, 3.5 Digit
72-7770 CAL D
The 72-7770 CAL D from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.
-
product
Positive Displacement (PD) Meters
Positive Displacement (PD) flow meters are volumetric flow measurement instruments ideal for low flow rates, highly viscous fluids, and measurement of flows involving starts and stops or pulsing. Positive displacement flow meters are similar in design to the gear pump. The principle of operation is reversed however; instead of the gears driving the fluid, the fluid drives the gears. A non-intrusive hall-effect sensor detects the movement of the gear and as each gear tooth passes the sensor, a square wave pulse is produced and a discrete volume of liquid is measured. The resulting pulse train is proportional to the actual flow rate and provides a highly accurate representation of the fluid flow.
-
product
Pulse Acquisition Board
MS 1818
*Used to measure the amplitude of discrete pulses driving relay coils/motors*Programmable No. of samples acquisition with programmable trigger option*Converts sine wave to square wave for pulse measurement*Measures amplitude of sine wave*16 Bit ADC interface*16 Bit data bus host interface*FPGA based design with flexible configuration*1K FIFO Storage
-
product
Pulse Delay Generators
Quantum Composers provides innovation and value to our customers with our diverse family of Precision Pulse Generators. A wide range of pulse generator technology has been created to fit the needs of any budget and application. Our square wave signal generators provide a cost-effective method to create and synchronize multiple sequences, delayed triggering, or any precisely timed series of events.
-
product
Utilities
Audio signal generator that include sine waves, square waves, white noise, and pink noise. The noise signals may be octave-band limited. In landscape mode, you can set sweep start and stop frequencies, and a time in seconds.
-
product
6U PXI Multi-Channel Analog I/O PXI Card
GX3348 Series
The GX3348 is a multi-channel analog I/O 6U PXI card which provides (3) programmable sources, a ground source connection, a pulse / square wave generator (A version only) and a 4 x 48 or 4 x 64 matrix - allowing the user to route the 3 sources, or ground to any of the 48 or 64 I/O channels. In addition, each I/O channel can be connected to a 16-bit A to D converter, providing DC voltage measurement capability for each channel. The module also offers (8) static digital I/O for controlling / monitoring a UUT's digital signals.
-
product
Square Wave Frequency Generator
F125
The F125 square wave frequency generator replaces our F150/155/105 frequency generators. It is a completely new design with many new features. The main one being that it can run standalone up to 1500 program files copied from a PC or Mac. It is also possible to connect the F125 to a computer via a USB port and control it with the F100 3.0 software for MS-Windows in the same way our F150/155/105 operate from a PC. Program files written for our current F150/155/105 are compatible with the new F125.
-
product
Paddle Wheel Flow Sensor
FSP
FSP - Paddle Wheel Flow Sensor, Using SUS and corrosion-resistant materials and design oxidation resistance, good stability and high resolution built-magnet rotor, NPN pulse square wave can be connected directly to the PLC / IPC IPC, the product is easy to maintain, easy to operate.
