Qualification
fulfills an absolute condition.
See Also: Performance Testing, Validation, Characterization
-
Product
Meter Qualification Board
MQB
-
Power-up and apply load to electric watt-hour meters for functionality testing with TESCO’s multi-position MQBs. These boards assist with AMI Meter Certification process and AMI meter qualification and communication testing.
-
Product
SuperGuard C Library Safety Qualification Suite
-
The SuperGuard C Library Safety Qualification Suite is a requirements-based test suite for the C standard library with full traceability between the requirements derived from the ISO C language definition and the individual library tests. It is designed to support the qualification of implementations of the C standard library for safety-critical applications, both for third-party (COTS) and for self-developed or maintained C library implementations.
-
Product
Qualification and Quality Control Tests
Techsquare
-
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Product
Meter Qualification Boards
WECO 8020, 8030
-
WECO Meter Qualification Boards by Radian Research enable extensive functional testing of single-phase and three-phase revenue grade electricity meters. Unlike Warm-up Boards and Load Boards that are limited to just powering the meter or applying a fixed current, WECO Meter Qualification Boards can test a variety of communications, disconnect and safety features. The WECO 8020 and 8030 have varying capabilities based on your requirements. They feature an innovative open socket design exclusive to RADIAN that ensures optimum operator safety. Capability, versatility and safety combine to make WECO Meter Qualification Boards THE logical choice.
-
Product
Qualification Tester
LQ404
-
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 12 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 3 cabinets. One is for the electronic components with the primary measurement devices and the other two hold the 12 load boxes.
-
Product
Qualification Hardware & Sockets
-
Reltech Limited holds over 35 years’ experience in the design and manufacture of all types of qualification test hardware. Our advanced technology products include: HTOL Boards (Mother and Daughter cards) Burn-In Boards HAST Boards THB (humidity) Boards Burn-In Modules and frames Dynamic Driver cards (Digital, Analogue and Mixed signal) Back Planes Voltage regulator cards Custom electro-mechanical assemblies DUT Cassettes and test Fixtures
-
Product
RF Testing, Screening and Qualification
-
DPACI has extensive experience in providing RF testing, screening, as well as QCI services to a diverse range of customers, such as Lockheed Martin, General Dynamics, and Ball Aerospace. We have a fully equipped RF and microwave lab with test capabilities ranging from 40 GHz to 300 GHz for providing RF packaging.
-
Product
Qualification Tester
CableIQ
-
CableIQ qualification tester is the first cabling bandwidth tester for network technicians. This Ethernet network cable testergives even the most novice tech the vision to see what speeds existing cabling can support, quickly isolate cabling from network problems, and discover what is at the far end of any cable.
-
Product
Detective Logic Analyzer
DDR3
-
Provides logic analyzer like deep transaction Listing and Waveform captureCan store up to 1G of captured StatesContinuous, real time analysis, not post-processingEye Detector guarantees valid data acquisitionExtensive Triggering and Storage Qualification allows precise insightProtocol Violation Detector provides hundreds of simultaneous, real time tests to JEDEC specificationsRow Hammer Analysis for potential data corruptionInteractions among up to 8 ranks, over two slots are analyzed.Mode Register Listing providedSupports Auto-Clock rate detect and clock stoppage Connects to the target under test with DIMM, SO-DIMM, and BGA interposers or a midbus probeIntegrated Microsoft Charts gives quick insight into large trace capturesTrigger In & Out allows the Detective to integrate with other test tools
-
Product
Shock & Drop Testing
-
Shock testing is often performed as part of a hardware qualification or design process. Information obtained during shock testing can improve the survivability of products as well as verify that they will perform properly in service. These types of tests require special transducers and measurement systems to record and process the high level, high frequency response.
-
Product
Weld Testing
-
Supports industries such as Aerospace, Nuclear, Automotive, Commercial Fabrication etc.Welding procedure consultancy and approvalWelder qualification test and codingWelding procedure certificationWelder performance qualificationOn site welding invigilationOffers a complete range of destructive and non-destructive testing facilities.Responsible Welding Co-ordinators available for customer supportCAA Weld Specimen SignatoriesCSWIP Approved Inspectors
-
Product
Evaporative Emissions Testing
GASERA ONE SHED
-
Evaporative losses from the fuel system are tested for vehicle certification. GASERA ONE SHED allows direct monitoring of evaporative emissions as part of the qualification testing procedures for vehicles. The GASERA ONE SHED’s photoacoustic technique is approved by the Environmental Protection Agency (EPA) and the California Air Resources Board (CARB).
-
Product
Qualification Tester
LQ402
-
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 6 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 2 cabinets. One is for the electronic components with the primary measurement devices and the other one holds the 6 load boxes.
-
Product
Microelectronics Test & Engineering Services
-
EAG's Microelectronics Test and Engineering lab network provides semiconductor and electronics design firms worldwide with test, debug, and early engineering support to help you with new product introduction. We actively service a broad range of semiconductor and electronics companies worldwide. Services include ATE testing, Reliability testing and qualification, ESD testing, Failure Analysis, FIB Circuit Edit and Debug. for both ICs and systems
-
Product
PCB Connectors
CMD Series
-
Smiths Interconnect's versatile, high density CMD connector solution for board to board and wire to board with built in coding and keying as well as ESA qualification
-
Product
Vibration Shaker and Control Amplifier
-
The performance of this Vibration System supports a wide variety of Vibration and Impact Shock capabilities, at g levels and weight-handling levels not previously available at Pacific. Applications include product development, design conformance, qualification, certification, and production screening to Military, Aerospace, Automotive, and Medical specifications.
-
Product
xDSL Line Qualifier
ELQ 2+
-
2,2 MHz Test Set for the qualification of ADSL & SHDSL lineswith data rate calculation. TDR & Bridge for cable fault location.
-
Product
Bluetooth RF Test System
FRVS
Test System
FRVS is recognized by the Bluetooth SIG as a validated test system for qualification testing of products to Bluetooth BR/EDR and low energy RF test specifications.
-
Product
Passenger Service Units
-
Astronics serves commercial applications for Passenger Service Units (PSU), offering vertically-integrated solutions through in-house design, manufacturing, and finishing capabilities. For most PSU programs, Astronics assumes full responsibility for design, development, and qualification of new technologies, including manufacturing and final assembly.
-
Product
GETTER Scorption Analyzer
DELTA-P MODEL 410
-
ORS manufactures the Delta-P Model 410 for companies that want to perform on-site getter qualification and lot conformance testing.
-
Product
Laser Diode Life Test
-
Life-tests consist of the highly accelerated ageing, under controlled conditions, of a group of lasers taken as a representative sample. Optical degradation of the laser diodes is observed and recorded by precisely measuring changes in the laser's operating characteristics during the test. Life-tests are used for vendor qualification of the laser diodes during product development and can be conducted throughout the production life of the laser.
-
Product
Open Top BGA Sockets
-
Ironwood has the most comprehensive collection of open top BGA and QFN sockets that can be used for qualification application, silicon FIB testing, system development, thermal characterization, burn-in application, etc. IC socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. Typical packages include BGA, LGA, QFN, QFP, WLCSP, etc. Open top allows access to the top side of IC. Below is an example BGA socket that uses low cost elastomer contact technology.
-
Product
Software
Tool Qualification Solutions
-
Many regulatory agencies require that any software tool used to tailor the safety life-cycle must be qualified to ensure that the tool is functioning correctly for the intended purpose. Genuen’s Tool Qualification Kits (TQK) provide a solid foundation for achieving formal qualifications used as part of your development process in highly regulated industries such as automotive, aerospace and medical.
-
Product
Ordnance Release Testing Services
-
Dayton T. Brown, Inc. can help ensure that your payload is delivered accurately and reliably every time. Our team is responsible for first article, production lot, qualification, and associated testing and engineering support for mechanical and electrical armament and missile launching systems. DTB can help you develop a customized test plan that combines testing across many specifications – environmental, dynamics, EMI/EMC, structural, and non-destructive. Some of the standards that we follow include:
-
Product
Bluetooth LE Protocol Qualification Tester
conformanceHarmony
-
The conformanceHarmony LE Tester is a robust testing solution recognized by the Bluetooth SIG as a validated test platform, focused on the qualification testing of products to the Bluetooth low energy specification. It is an integrated software/hardware test platform for Bluetooth protocol qualification testing that provides:
-
Product
Semiconductor & Electronic Systems Test and Diagnostics Services
-
Reliability Test and Diagnostic services are offered to a wide range of customers that are active as Fabless Semiconductor or Integrated Device Manufacturers, automotive electronics supplier, Telecom and ICT application specialists, Industrial and Medical electronic system manufacturers or in Aerospace and Space applications. Independent high tech test and diagnostic service laboratory. IC and electronic module qualification. ESD and Latch Up testing. Design assessment by HALT/HASS. Failure and construction analysis.
-
Product
HIL/V&V Solutions
-
SPHEREA designs test systems derived from our modular platform for V&V applications, for the whole development chain, from design to qualification
-
Product
Device Modeling Products
-
Our products and premier solutions provide for characterization and modeling of cutting-edge CMOS and compound semiconductor devices. Keysight is the only vendor that provides complete end-to-end modeling solutions, from automated measurements, accurate device model extraction, comprehensive qualification to final process design kit (PDK) validation. Comprehensive modeling services are offered, supported by Keysight's expert engineers and advanced labs. Our key device modeling and characterization EDA software and hardware solutions are included below.
-
Product
3U PCIe Gen2 ATR Style Chassis
Crosswind 600
-
PCI-Systems innovative 1-2-3 system. 1: Lab unit 2: Configure unit 3: Deploy unit! All our chassis and prototype systems can be deployed without needing to change out the chassis. Add Front and rear custom covers and full sealing and you are ready to go to qualification!
-
Product
Non Destructive Testing (NDT)
-
NDT covers a wide group of testing techniques used to evaluate the properties of a material, part, product, weld or system without causing damage. NDT carried out at KLL includes:Liquid Penetrant Testing (LPT) is used for the detection of surface breaking discontinuities on magnetic and non-magnetic metallic materials.Fluorescent and colour contrast penetrants are available to be used in the following methods:-Water washableSolvent removablePost emulsifiableMagnetic Particle Inspection (MT/MPI) is used for the detection of surface breaking and slightly sub-surface (up to 2mm) discontinuities.Bench type crack detectors and portable units are employed producing various waveforms (i.e. A.C, HWDC and induced magnetic flow) to give both circular and longitudinal magnetism.On-site testing is carried out using electro magnetic yokes and permanent magnets producing induced magnetic flow.Ultrasonic Flaw Detection (UT), also known as Ultrasonic Inspection, is used for the detection of volumetric discontinuities in ferrous and non-ferrous products (forgings and castings etc.), and welds in magnetic and non-magnetic materials.UT is capable of penetrating metals, dependent on the material characteristics, up to 10m in length.Some thickness and depth checks can also be carried out using ultrasound.Radiography services are available through sub-contract booked in advance. Notice is required for on-site work.Personnel are available at short notice for in-house or on-site work in the UK and overseas.All inspectors undertaking non destructive testing (LPT, MT/MPI and UT) are qualified to, and meet a minimum of, PCN Level 2.PCN Level 3 supervision is available in-house for LPT, MT/MPI, UT offering consultancy services including procedure writing and commentary, auditing of techniques and Level 3 Supervisor cover.We can assist clients in product qualification, material testing, quality assurance and audit programmes.
