Filter Results By:
Products
Applications
Manufacturers
Gas Flow
-
product
Ultrasonic Gas Flow Sensor
GB Series
Panasonic Industrial Devices Sales Company of America
A compact, dual-function Ultrasonic Gas Flow Sensor that measures gas flow and gas concentration for flow rates from 1 to 25 Liters per minute. This Ultrasonic Gas Flow Sensor uses a unique time-of-flight design with an onboard processor to make highly accurate measurements of both gas flow and concentration. Suitable for use with many gases in an easy to implement format.
-
-
product
Gas Flow Sensors
ESRF-ESF Sensor
ESRF-ESF is one of the few gas flow sensors featuring bidirectional gas flow sensing of up to ±300 ln/min with a total error band of < 1.25% RD. ESRF-ESF gas flow sensors provide calibrated and temperature compensated output on an SPI, I2C bus or analog output making them plug & play for direct interfacing to low voltage MCUs and systems. The user is provided with a multitude of interface and output options so that the right sensor configuration can be selected based on the specific requirements for each application.
-
product
Gas Flow Meters & Controllers
Accurate Mass Flow Measurement Sierra designs and manufactures a wide range of today's most advanced analog and digital gas flow meters, mass flow meters, controllers and switches across three core technologies: Capillary Thermal, Immersible Thermal, and Mass Vortex. Each gas flowmeter or controller meets exacting standards, and we can also customize your flow rate sensor to meet application requirements (often free of charge).
-
product
Gas Flow Sensors
ESRF-HF Transmitter
The ESRF-HF is a family of mass flow transmitters which enable fast and accurate measurements of gas flow over a wide dynamic range. Each transmitter integrates a MEMS flow sensor and readout electronics inside a housing with very small form factor made from stainless steel. The duty pressure of the flow transmitter is 11bar. All measurement data are fully calibrated, and temperature compensated on board, leading to a reduced temperature coefficient and high measurement accuracy.
-
product
Gas Flow Controller
GFC Series
The GFC series enables quick interchange with standard MFCs: same mechanical outline, 4-VCR connectors on standard model, and 15-pin analog connector.
-
product
Gas Flow Meters
There are innumerable circumstances where gas flow rates need to be quickly and precisely measured. You’ll always be prepared with Netech’s versatile range of gas flow meters, which are designed to measure several types of gases including air, N2, O2, CO2, and He.
-
product
Digital "A" Flow Controller for High Flow
HFM-D-306A / HFC-D-308A
Mass flow techniques provide RELIABLE, REPEATABLE AND ACCURATE gas flow rate measurements.HFM-D-306A/HFC-D-308A mass flow instruments have flow ranges from 0-2500 slm to 0-10000 slm; provide analog and digital outputs, and are constructed of stainless steel. Easy, user friendly digital communications with windows based software interface available. Available with a variety of elastomer seals for maximum flexibility.Self diagnostics of the sensor, valve and overflow are included in the digital features. Also of interest is the auto zero feature which detects when the valve is closed and automatically resets the zero. These mass flow meters and controllers can store up to 10 calibrations of different ranges and gases. Another feature is the built in totalizer for monitoring gas usage under user set conditions.
-
product
Super high temperature hall effect measurement system
Super high temperature hall effect measurement system that is useful to flow gas into chamber with sample. - Newly developed furnace that makes it possible to increase over 800 and use for measuring hall effect. - Gas flow control system in order to flow various gas. - Sample holder for high temperature. (keep the good contact on 800) - High Temperature control system (DC power) On condition of specific temperature with gas flow , new semiconductor materials have been developed to see electrical property's change.
-
product
Long Term Test Kit
When long term electro-chemical tests (>1000 hours) are run to monitor the cell degradation at the cathode for example, it is important to avoid any contaminant in the gas flow rate.Inconel 601 flange equipped with alumina housing and alumina tube to feed the gas to the electrode during long term test (>1000 h)Typical poisoning is coming from the chromium contained in the steel tubing. The volatile chromium species (Cr6+) will flow into the cathode (with the air) and thanks to the intake of electrons at the electrode, the chromium ion will transform to chromium oxide and be deposited at the cathode triple point. In such a case, the long term test kit is used. The Inconel 601 flange is equipped with an alumina housing (>96 % Al2O3) and the air (or other gas) is led through an alumina tube. The long term test kit is fully compatible with other functionalities proposed with the Open Flanges™ test Set-Up as the integrated steamer or the small pellet test kit. The long term test kit can be implemented on the fuel, on the air or on both sides.
-
product
DELTA™ IV 4-zone Flow Ratio Controller
DELTA™ IV 4-zone Flow Ratio Controller is a digital controlled, browser-enabled, process control instrument providing the latest gas flow ratio measurement and control technology to meet the demands of multi-channel flow distribution for semiconductor, flat panel, and solar panel process uniformity and control. It is available in EtherCAT® or DeviceNet™ providing the latest gas flow ratio measurement and control technology to meet the demands of multi-channel flow distribution.
-
product
Variable Constant Differential Flow Controller
VCD 1000
The Porter Model VCD 1000 flow controller is precision-engineered to control low gas flows at constant mass flow rates regardless of changes in downstream pressure.
-
product
Miniature Pressure Controller
VSO®-EP
Parker’s VSO- Electronic pressure control unit is specifically designed for precision gas and microfluidic flow control
-
product
Vapor Concentration Monitor
IR-300 Series
Metal-Organic Chemical Vapor Deposition (MOCVD) is widely used in the manufacture of LEDs, optical devices and other components. Liquid and solid precursors are delivered to the reaction chamber by controlling the temperature, pressure and the carrier gas flow rate (bubbling method). Process results can be affected by changes especially in temperature and liquid level. The in-line IR-300 Series measures and reports the precursor concentration in real time.
-
product
Dual Pitot Tube Flow Meter
PTFM-ONE-DT
The Dual Pitot Tube Flow Meter, PTFM-ONE DT is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers, with a sampling rate of 1kHz to accurately measure highly pulsating exhaust flows. This rapid capture rate ensures that any pulsations or exotic behaviour caused by the engine is measured, and the unique design of the PTFM-ONE DT means reverse flows can be calculated, with the same guarantee of sensitivity.
-
product
Flow And Differential Pressure Sensors
ACEINNA’s flow and differential pressure sensors are designed to serve the need for mass flow and pressure sensing in multiple applications such as gas meters, process control, HVAC, medical, chemical, food and beverage, etc. We offer two newly launched and announced product lines, the MFC2000 family of gas flow modules and the MDP200 differential pressure sensor.
-
product
Mass Flow Meters
Alicat Scientific, Incorporated
Use mass flow meters to measure gas flow from 0.5 SCCM to 10,000 SLPM, with accuracies as good as ±0.5% of reading or ±0.05% of full scale and a measurement range of 0.01-100% (10,000:1 turndown).
-
product
Extractive Gas Analyzers
Reliable gas analysis — even under harsh process conditionsSICK's extractive gas analyzers can be used in a large number of applications. The extractive measurement technology extracts a partial gas flow from the gas duct, conditions the extracted gas and feeds it to an analyzer module under constant conditions. All the measurement technology that SICK offers – from gas sampling and conditioning right through to the numerous analyzer modules – is perfectly tailored to the measurement task concerned.
-
product
Digital "A" Flow Controller for High Flow
HFM-D-306A / HFC-D-308A
Mass flow techniques provide reliable, repeatable and accurate gas flow rate measurements.HFM-D-306A/HFC-D-308A mass flow instruments have flow ranges from 0-2500 slm to 0-10000 slm; provide analog and digital outputs, and are constructed of stainless steel. Easy, user friendly digital communications with windows based software interface available. Available with a variety of elastomer seals for maximum flexibility.Self diagnostics of the sensor, valve and overflow are included in the digital features. Also of interest is the auto zero feature which detects when the valve is closed and automatically resets the zero. These mass flow meters and controllers can store up to 10 calibrations of different ranges and gases. Another feature is the built in totalizer for monitoring gas usage under user set conditions.
-
product
4 Point Probe Sheet Resistance/Resistivity Measurement with Temperature Controled System
TCR-600
*Controlled Thermo-chuck (room temperature～600℃/less than 20 minutes)*600C compatible probe head with 1mm linear*Controlled with vacuum sensor, digital thermo-meter, vacuum gauge and gas flow meter*Temperature measuring accuracy：±（0.5% + 1℃）
-
product
Air Quality / Gas / Flow Sensors
Panasonic Industrial Devices Sales Company of America
Panasonic offers compact, high sensitivity Air Quality, Gas and Flow Sensors for use in equipment or automation processes. Designed for air quality / IAQ monitors and home appliances, the Laser Type PM (Particulate Matter) Sensor can detect dust particles down to the 0.3 m size.
-
product
Gas Meter Synthetical Test Bench
SY8506
Hong Kong Songyang Industrial Ltd.
The test of the error of the rate of flow:Using the gas flow standard device (in the shape of the bell prover) as our standard equipment, we can figure the standard volume of the tested gas by using the high-precision revolving encoder to measure the descending displacement of the bell prover.
-
product
Test Rig for Flashback Arrestors
The WITT test rig allows for the testing of flashback arrestors and check valves on a regular basis.With just one device all performance tests can be carried out: leak-tightness to the atmosphere, test of check valves against reverse gas flow, functionality of the pressure sensitive gas cut-off valve and measurement of the flashback arrestors’ flow capacity.The Test Rig 722 is easy to use, has a robust design and requires no maintenance.
-
product
Constant Temperature Anemometry (CTA) - Hot-Wire Anemometry - Thermal Anemometry
Constant Temperature Anemometry (CTA), also known as Thermal Anemometry, is a technique for the measurement of turbulence in 1, 2 or 3-dimensional gas and liquid flows, using hot-wire or hot-film probes inserted in the flow. CTA is particularly suitable for the measurement of flows with very fast fluctuations at a point (high turbulence) and the study of flow micro structures, where there is a need to resolve small flow eddies down to the order of tenths of a mm.
-
product
Flow Measurement
HighReach Measuring & Controlling System Co.,Ltd
Involves using flow meters that measure the flow rate of steam, liquid, or gas flowing through a pipe.
-
product
Gas Flow Standards
Fluke Calibration offers molbloc/molbox gas flow calibration systems to calibrate flow meters and controllers over a very wide range of flows. The systems are fast, precise and transportable and can be fully automated using COMPASS for Flow software. molblocs, which are the heart of the measurement system, are mechanically stable, gravimetrically calibrated laminar flow and sonic nozzle elements.
-
product
Ultrasonic Exhaust Flow Meter for Real-time Measurement of Vehicle/Engine Exhaust Flow
EXFM-ONE
EXFM-ONE employs an ultrasonic method for measuring exhaust gas flow rates directly from a vehicle or engine. The unit can be used for various applications such as real time mass measurement of raw exhaust gas combined with MEXA-ONE (Motor Exhaust Gas Analyzer), or for Particulate Matter/emission measurement combined with partial flow dilution system such as MDLT (Partial Flow Dilution Tunnel) or BMD (Bag Mini Diluter). Fuel consumption evaluation is also available when EXFM-ONE is paired with an optional air-to-fuel ratio (AFR) analyzer.
-
product
CEMS
FMD 09
IMR Environmental Equipment, Inc.
The continuous measurement of velocity and temperature of gas flows is much important at operation of a system with flowing gases (e.g. hall outlet air, exhaust etc.).
-
product
Multi Gas Analyser
OR-703
The OR-703 multi gas analyser expands the capabilities of the PF-300 series gas flow analysers. Its compact ad lightweight housing makes the OR-703 an ideal and integrated solution for the accurate measurement of anesthetic gas concentration.
-
product
DELTA™ II 2-zone Flow Ratio Controller
The DELTA™ II Flow Ratio Controller divides and controls mixed process gas flows to either multiple chambers or zones within a process chamber at ratios specified by the user maximizing process uniformity and repeatability. It is available with EtherCAT® or DeviceNet™ communications.
