Bridge Amplifiers
Increase a transducers signal to measurable levels.
-
product
Solid State Power Amplifiers
Skylink SSPAs incorporate state-of-art DPD and well-done Heat Dissipation technologies with available LDMOS, GaN & GaAs Chips. Solutions of SSPA frequency range from 9kHz to 50GHz and output power up to kilowatts and includes basic PA modules to integrated chassis with embedded software for local and remote control and monitoring.
-
product
Single Channel High Voltage Linear Amplifier
A800
The A800 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of ±400V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±4 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
High Voltage Amplifier
HA-400
*400Vp-p(±200V DC) *160mAp-p(±80mA DC) *Bandwidth: ≦600KHz(200Vp-p) *Slew Rate: 300V/us *Gain(AMPL): 0~90(10 Turn VR) *DC Offset: ≦0~±200V (10 Turn VR + SW) *Output Resistor: 50Ω
-
product
Saluki SE2041 DSP Lock-In Amplifier
SE2041 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 60 MHz. With the advantage of the latest digital signal processing technology and high-speed 250MSPS 14-bit ADC, SE2041 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noises. The performance of SE2041 is as good as other lock-in amplifiers all over the world, even better than them in some certain parameters, such as measurement accuracy, SNR, dynamic reserve, which meets the needs of scientific research and industrial application well.
-
product
Automatic Level Control Amplifier
RF Lambda’s automatic level control amplifiers allow customers to implement an AGC function into their system to tune the gain and stay linear with high input signals without the need to manually control the input level. Hermetically sealed options are available upon request.
-
product
Traveling Wave Tube Amplifier
Skylink a leading provider in design and manufacture a wide range of traveling wave tube amplifiers(TWTAs) and microwave power modules(MPMs).Skylink's new generation of MPMs are based on a modular design, and use new technology, material and computer simulation system to improve weight, size and efficiency.Our main MPM series frequency covers range from 2 to 40GHz and providing more than 100W. They combine a helix TWT, a solid state amplifier and an integrated power conditioner in a compact package.
-
product
Unipolar High Voltage Linear Amplifier
P150
The P150 is a general purpose linear amplifier having a fixed amplification of 20 times and capable of unipolar high voltage output of +150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to +10 V can be used as an input device. The amplification can be set to x15 (or other value) on request.
-
product
Composite 1×6 Video Distribution Amplifier
VDA106
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
Cable Fault Locator With Time Domain (Intelligent Bridge)
GT00ZD00ZY
GAOTek Cable Fault Locator with Time Domain has a reflectometer to locate faults in metallic cables and Intelligent bridge for tesing the broken line
-
product
LVDT Sensor Amplifiers
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
product
Modules - Modules, Bridge
Vishay’s bridge modules feature voltage ratings from 50 V to 1600 V in single-phase and three phase configurations and in a wide range of package options.
-
product
Variable Gain Amplifiers
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support a broad family of Variable Gain Amplifiers (VGAs) for RF, microwave, and millimeter wave applications. Our VGAs cover frequencies from 50 MHz to 40 GHz and are used in a variety of Network, Commercial and Aerospace and Defense applications. These products are available in industry standard plastic packaging and are designed for both 50 Ohm and 75 Ohm applications.
-
product
Power Amplifier For Real-Time Dynamic Simulation(RTDS) Application
As the first power amplifier manufacturer in China, PONOVO has been offering various power amplifier products for customers in China and other countries since 2001. PONOVO has launched both conventional power amplifier for power system use and also 4-Quadrant power amplifier for more filed application, such as microgrid, windfarm, PV, HVDC, areospace, battery simulation, etc.
-
product
RF Amplifiers up to 2500 MHz
L and S Band 1,2,4, and 8 Kilowatt rack mount solid state microwave amplifiers ideal for CW and pulse TWT amplifier replacement utilizing GaN technology and rivals the TWT amplifier in size and weight. Also available is our broad line of high power modules including 25, 50, and 100 watt pallets for integrating into your own power amplifier design.
-
product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5021
The HMMC-5021 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5021 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gain response and excellent port matches over the 2-22 GHz frequency range.
-
product
High Speed High Voltage Amplifier
WMA-320
The WMA-320 is a high voltage, wide bandwidth laboratory amplifier. Its high output voltage, current and wide bandwidth have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-320 can be used for MEMS actuation, EO-modulators, PZT (piezo) positioners, ultrasonics, and many other applications.
-
product
Directional Couplers & Bridges
A complete line of coaxial single and dual port directional couplers, and bridges for isolating, separating, and combining RF and microwave signals in such applications as power monitoring, source leveling, swept transmission and reflection measurements.
-
product
Low Noise Amplifiers
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
-
product
mm-wave Bridges for EPR/NMR Spectrometers
ELVA-1 produces mm-wave bridges and components for EPR spectrometers. Lots of scientific laboratories in the world use ELVA-1’s products in their EPR experiments. Up to 170 GHz operating frequency
-
product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
High-Speed System Sync and Distribution Amplifier - SOSA Aligned 3U VPX
Model 5503
- Supports Xilinx® Zynq® UltraScale+™ RFSoC FPGAs- Synchronizes up to 32 channels across four Quartz boards- Synchronizes sampling and data acquisition for multichannel systems- Provides single sample accurate synchronization between multiple channels and multiple boards- Synchronizes gating and triggering functions- Optional VITA 67.3D optical interface for backplane gigabit serial communication
-
product
Telecom Optical Amplifiers
Thorlabs' optical amplifiers for telecom applications are available as complete benchtop systems or as pigtailed butterfly packages. Our line of benchtop optical amplifiers includes a praseodymium-doped fluoride fiber amplifier (PDFA) and erbium-doped fiber amplifiers (EDFAs). Our optical amplifiers available in pigtailed butterfly packages include InP/InGaAsP or GaAs/InGaAs semiconductor optical amplifiers (BOAs or SOAs), and high-speed optical switches.
-
product
Driver Amplifiers
Analog Devices RF amplifiers are designed utilizing the company’s leading amplifier and RF IC expertise. Our extensive family of single-ended input/output, fixed-gain amplifiers can be used from dc to microwave and include gain blocks, low noise amplifiers, intermediate frequency amplifiers, driver amplifiers, and differential amplifiers. These devices offer high linearity, low noise figures, and various fixed-gain options, as well as low power consumption; they are all fully specified over frequency, temperature, and supply voltage for use in a variety of applications.
-
product
Low-noise High-voltage Amplifier For Tube-scanners -
HV200/5
The HV200/5 is a high-precision HV-amplifier designed for the control of tube scanners. It takes three input voltages In X, In Y and In Z (-10 V to + 10 V), amplifies them separately (input gain switches: x1, x2, x5, x10, x20) and adds an offset voltage between -10 V and +10 V. In a 2nd stage, the signal is amplified by a factor of 20. This enables its use as HV amplifier in scanning image acquisition applications, such as STM or AFM, with the capability to shift the scan range in high resolution imaging.
-
product
Rugged Amplifiers And Transmitters
Communications & Power Industries
CPI TMD began developing power supplies at the end on the 1980s, expanding its amplifier product line. By leveraging this expertise together with its proficiency in microwave tubes and the complexities of integration, CPI TMD has build a thriving amplifier and transmitter business to serve the needs of its defence and communications customers.
-
product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
Wideband GaN Amplifiers
The Teledyne RF & Microwave family of GaN-based amplifiers maximizes power density and efficiency, and establishes a new benchmark for small size in the 0.1 to 6.0 GHz range that operates over multi octave. With dimensions of 2.5"L x 2"W x 0.42"H at only 2.1 cubic inches, these modular, non-ITAR GaN amplifiers maintain the rugged design characteristics needed for harsh airborne and land based requirements.
-
product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
-
product
Fiber Transmitter With Fiber Amplifier
FTFA 822B - 824B
- Work as Transmitter & Fiber Amplifier- AGC - Automatic Gain Control- Built in RF Booster- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lesers with Isolaters- Variable SLOPE Control- Output Wavelength : 1310nmPower Options :- 40V DC- 12V DC / 2 Amp- STB Adapter along with PSP- 7.4V, 2600 mAH Battery
-
product
Sound Source And Power Amplifier
Designed for acoustic application, with strong signal transmission capability and flexible measurement.
