Bridge Amplifiers
Increase a transducers signal to measurable levels.
-
Product
Single Channel High Voltage Linear Amplifier
A800
-
The A800 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of ±400V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±4 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Amplifiers
-
The amplifier is one of the most important components in a pulse processing system for applications in counting, timing, or pulse amplitude (energy) spectroscopy, providing the pulse-shaping controls needed to optimize the performance of the analog electronics.
-
Product
Shunt Isolation Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Especially to accurately measure large DC currents via shunt resistors, ie for making isolated detection of mV voltage on shunts. Variants with calibrated range selection. Working voltage up to 3600 V AC / DC.
-
Product
Charge Amplifier
CH-1200A
-
CH-1200A is a high-performance charge amplifier to convert charge signal to voltage signal. Built-in integration function allows optimization of the signal which is input to the vibration data analyzer connected.Changing into a multi-channel amplifier is easy by connecting multiple units.
-
Product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
-
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Modules - Modules, Bridge
-
Vishay’s bridge modules feature voltage ratings from 50 V to 1600 V in single-phase and three phase configurations and in a wide range of package options.
-
Product
Bridge Monitoring
-
Structural Health Monitoring of BridgesDewesoft data acquisition systems are used in structural health and seismic bridge monitoring projects ranging from structural mechanics to continuous monitoring of large, complex structures. The systems provide distributed, high-channel-count and remote monitoring for highway overpasses, roads, buildings, and bridges.
-
Product
Portable Bridges
-
A range of affordable battery operated test equipment for the measurement of resistance.
-
Product
Four Quadrant Power Amplifier
PAV3000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Class-D Audio Amplifiers
-
Analog Devices is a leader in Class-D audio amplifiers and audio signal processing, and we deliver audiophile-level performance with our proven analog and digital technology. We offer a wide range of audio amplifiers, including industry-leading microphone preamps, microphone drivers, line drivers, and receivers. Our Class-D amplifiers, in particular, are among the lowest power and lowest distortion in the industry. Our portfolio includes Class-A, Class-B, and Class-D audio amplifier offerings, along with a breadth of power ICs. Analog Devices amplifier products have been used in many high volume consumer products where the highest audio quality is expected. The lowest power consumption also enables this performance in many battery powered applications as well.
-
Product
Premium Headphone Amplifier
A 2
-
A premium model with a discrete configuration and full analog circuit that was created to drive the T 1 thoroughly.
-
Product
CATV Amplifiers
-
Electronic devices that boost weak TV and broadband signals (audio, video, data) traveling through coaxial cables, compensating for signal loss from splitters, long cable runs, or network nodes to maintain strong, clear picture/data quality for multiple devices, operating across specific frequency bands for both forward (downstream) and reverse (upstream) paths.
-
-
Product
Countermeasures Amplifier
CMA-100
-
CMA-100 Countermeasures Amplifier is a high gain audio amplifier used to detect and identify certain types of surveillance devices attached to building wiring such as telephone wiring, LAN and server systems, AC power, and alarm wire. The CMA-100 Countermeasures Amplifier functions employ a sophisticated automatic gain control circuit that is superior to most audio amplifiers.
-
Product
Gateways And Bridges
FarLinX Connect Mini
-
A compact remotely manageable HDLC Bridge and TCP to HDLC/LAPB Converter.
-
Product
JFET Input Amplifiers
-
Analog Devices JFET input op amps or FastFET high speed (>50 MHz) input op amps provide high input impedance and ultralow input bias currents for high speed applications. The majority of our FET input op amps feature wide supply ranges from +5 V to 12 V or higher and feature rail-to-rail outputs enabling wide dynamic range.
-
Product
Communications/Data Link Amplifiers
-
Amplifiers specific to the Communications systems include a wide range of Solid State Power Amplifiers (SSPAs) and Low Noise Amplifiers (LNAs) originally from Paradise Datacom and a range of organically developed products within TMS. Satcom SSPAs are considered a core competence of Paradise Datacom's product line who have invested heavily in converting it's complete amplifier offering from GaAs to GaN from C-Band all the way to Ka-Band.
-
Product
Components - Power Amplifiers (FPA)
FPA Series
-
FPA series driver amplifiers and power amplifiers are discrete and/or MMIC pHEMT device-based amplifiers that operate over the frequency range 18 to 110 GHz for high output power applications. The amplifiers are offered in two categories, standard and custom built up to 250 GHz.The custom-built amplifiers are offered in various RF interfaces, including standard waveguide or coaxial connectors, for convenient system integration. The optional input and output integrated isolators are available to further improve the port return loss.
-
Product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781209-01
Strain/Bridge Input Module
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
Benchtop Amplifiers
-
Benchtop, broadband driver amplifiers are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a high output power and a superior gain flatness and low noise performance. The standard offering focuses on general purpose applications and covers the frequency range of 1 to 110 GHz. However, custom designs are also offered to meet any user’s specific needs.
-
Product
High-Frequency Signal Amplifier
VCH-605
-
High-frequency signal amplifier VCH-605 is designed to amplify and multiply sinusoidal signals with a frequency of 1-100 MHz.
-
Product
Crossed-Field Amplifiers
CFAs
-
Communications & Power Industries
CPI BMD’s crossed-field amplifiers (CFAs) are broadband, phase-stable microwave amplifiers used in coherent radar chains to efficiently generate very high peak output powers from relatively low input voltages which can be either applied to the cathode or an electrode similar to a TWTs cathode or grid pulsing, and in relatively small, lightweight packages. These characteristics make CFAs particularly well-suited for applications in which the transmitter must be either airborne, transportable, mobile or portable.
-
Product
Dual Channel High Voltage Linear Amplifier
F10AD
-
his unit contains two independent F10A amplifiers that share common ground reference and power supply.
-
Product
Combustible Trip Amplifier Module
TA102A
-
The TA102A is a single-channel Combustible Gas Trip Amplifier Module designed for use with one General Monitors intelligent transmitter to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through a front panel interface (mode / select switch and digital display).
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
Hybrid Amplifiers
LNA
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of hybrid amplifiers cover a frequency range of 10 kHz to 6 GHz. Each amplifier is designed to be unconditionally stable and have excellent cascadability. Our amplifiers are designed using thin film technology and are integrated components that include internal DC biasing circuitry, allowing them to maintain excellent electrical performance over the 55˚C to 100˚C range. Hermetically sealed and screened up to space level, these amplifiers are ideally suited for hi-reliability and mission critical applications.
-
Product
RF & Microwave Broadband Amplifiers
-
SHF Communication Technologies AG
SHF has been active in the design and production of broadband RF-microwave amplifier. The outstanding performance makes our amplifiers suitable for a wide variety of applications in R&D. This includes not only optical communications, but also satellite communications, high-speed pulse experiments, data transmission, quantum communication, radar and antenna measurements.
-
Product
mAEStro Digital Audio Re-Clocking Distribution Amplifier
-
The mAEStro ADA-100 receives AES/EBU (AES3) or S/PDIF digital audio and provides four re-clocked digital audio outputs. It automatically detects sample rates from 32kHz to 96kHz with low-jitter clock recovery. The outputs are completely regenerated using a jitter-free clock that is locked to the source input. The rugged self-contained metal enclosure has a number of mounting options from desktop, to rear side-rail rack mounting, to ganged front-side or rear-side rack mounting.
