Carriers
Carrier devices are practical for adapting your product to a standard interface for testing on the bench or in the chamber.
-
product
Selective RF Detector
Raksa iDet
RAKSA iDet detects: cellular phones of GSM900/1800, UMTS(3G), CDMA450 standards; cordless DECT phones; Bluetooth and Wi-Fi devices; wireless video cameras; radio transmitters with analog modulation (AM, FM, PM); radio transmitters with digital modulation and continuous carrier (FSK, PSK, etc.); radio transmitters with wideband modulation up to 10 MHz bandwidth.
-
product
cPCI to PMC Compatible Adapter/Carrier
cPCIRepeat32
cPCIRepeat32 ( cPCI to PMC ) adapter / carrier converter card provides the ability to install up one PMC card into a cPCI slot designed for bus expansion. The J2 connector can be left off for non bus expansion positions.
-
product
FMC for Data Communication Dual 1 Gigabit Ethernet FMC
FMC431
Sundance Multiprocessor Technology Ltd.
The FMC431 is a dual 1 Gigabit Ethernet FPGA Mezzanine Card with two RJ45 connectors available on the front panel. Compliant with the VITA 57.1 standard the FMC431 offers a High Pin Count connector but is compatible with FPGA carrier cards with Low Pin Count connectors. The Ethernet interface (1000BASE-T) is either implemented using RGMII (Low Pin Count compatible) or SGMII (High Pin Count compatible). The FMC431 also offers the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC431, thus offering users with the ability to build a complete data acquisition, waveform generation and communication solution while using a single FMC site on an FPGA carrier card. The FMC431 is an ideal solution to bring Ethernet connectivity to an FPGA based system and ensure reliable external communication.
-
product
PMC to PCI Express Adapter w/ TSI384
6083
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI express primary side and a PCI/PCI-X secondary side.
-
product
Mezzanine System Carrier
MMS8010 / MMS8011
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
product
Flow Meter Sensor
RF Pickups
SPECTEC Innovative Sensor Solutions
SPECTEC RF pickups are excellent for applications that require near zero speed and zero magnetic drag sensing characteristics, such as flow meter sensor applications. SPECTEC RF (modulated carrier) sensors have a long history of use in turbine flow meters and turbine engines in the aerospace, petroleum, chemical, pharmaceutical and food industries.
-
product
Large Range Resistivity Tester
HS-SFRT
HS-SFRT silicon filament resistivity tester is an advanced silicon cylinder resistivity tester, which can measure silicon filament, silicon phosphorus ingot, silicon boron ingot, seed crystal and so on. As it eliminates Peltier effect, Seebeck effect, minority carrier inject effect and so on, So it improve the accuracy greatly. The testing resistivity ranges from 0.0005Ω·cm to 50000Ω·cm. It is accurate, stable and convenient and a good friend to Siemens polysilicon material producer, SH4 polysilicon material producer, UMG polysilicon material producer and so on.
-
product
Slave Dual Industry Pack Carrier
CPCI-SIP-3
The new CPCI-SIP-3Module provides a 3U high performance flexible I/Oscheme, that supports industry standard IndustryPacks. Choose from over a 100 different IndustryPacks from Alphi Tech and others. For applicationrequiring low cost, high density I/O or unique combinations, the CPCISIP-3 is the perfectsolution.
-
product
ARINC-429 Multi-Channel Test & Simulation Module for Excalibur 8000 Family of Carrier Boards
M8K429
The M8K429 is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 8000 family of carrier boards. The module supports up to five ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word. The receivers allow for filtering and multi-storage modes of Data Words. The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention.The M8K429 comes complete with C-driver software library including the source code.
-
product
Voltage Meter
MDS32
M-module MDS32 is a mezzanine module designed to analyze the state of discrete sensors. М-module MDS32 is installed on the mezzanine carrier - module НМ-М and connected to it via a local information highway. Up to four m-modules of various types can be installed on the NM-M module. The NM-M module together with the m-modules installed on it forms a C-1 VXI module for 64 analyzing channels and is used to create information measuring VXI systems.
-
product
Electronic Resistance Store
MPS2
The MPS2 module is a mezzanine module designed to form DC resistance in two channels with a four-wire measurement circuit. MPS2 is installed on the mezzanine carrier - the NMU module and is connected to it via a local information highway. Up to four mezzanines of various types can be installed on the NMU module. The NMU module together with the mezzanines installed on it forms a VXI module of the size C-1 and is used to create information measuring VXI systems.
-
product
3U OpenVPX Switch, PCIe Gen 3 With Integrated Health Management
VPX004
The VadaTech VPX00x family, with integrated health management, are the most feature-rich VPX Switch products on the market. The management software is based on VadaTech’s robust Carrier Manager and Shelf Manager which have been deployed for years with proven results. The MCMC manages the Power Modules, Cooling Units, and up to 12 payload modules within the chassis. It also manages the PCIe Gen3 switch and the standard GbE with 10GbE uplink Base Channel switch.
-
product
ATCA I/O Rear Transition Module (RTM)
ART001
The ART001 is an I/O expansion ATCA Rear Transition Module (ARTM) that provides GbE, 10 GbE, PCIe and Management I/O for the front blade. The module is designed to mate with any ATCA Carrier. ART001 provides PCIe x8 access via an iPASS connector to the rear. The GbE rear access is provided via six SFP ports and five RJ-45 ports. The module has dual 10 GbE PHY which mates to the host via the zone 3 connector and provides dual SFP+ to the rear.
-
product
Resistance Meter
MT8-4L
М-module МТ8-4Л is a mezzanine module designed to measure the resistance of resistive sensors using a four-wire measurement circuit in eight channels (eight-channel digitizer). М-module МТ8-4Л is installed on the carrier of mezzanines - module НМ-М and is connected to it via a local information highway. Up to four m-modules of various types can be installed on the NM-M module. The NM-M module, together with the m-modules installed on it, forms a VXI module of size C-1 and is used to create information measuring VXI systems.
-
product
4-Channel Broadcast Monitor
The COMM-connect Entry Level Broadcast Power Monitor type 3025 can control two external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. Equipped with the RMS Probes the Power conversion algorithms handles multi carrier, multi mode signals. With the 3026 Diode base probe the power readout gives good repeatable results. The power readout is auto scaled and VSWR will be calculated between the two probes. The COMM-connect Entry Level Power Monitor gives a number of application to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Press Down Rods Bed of Nails Testers
Prober Press Rods Family
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
product
Carrier Acceptance Test Solutions for Network Operators
The Rohde & Schwarz carrier acceptance test systems provide access to the most important test plans of the world’s major mobile operators.Voice over NR, data throughput, protocol, positioning, RF, RRM and application testing – all relevant test scenarios are available on a common hardware platform.The entire range of 5G NR testing modes are available, covering sub-8 GHz (FR1) and mmWave (FR2) frequencies, and both non-standalone (NSA) and standalone (SA) modes.Contact your Rohde & Schwarz sales representative to learn more about the latest products and features.
-
product
Vapor Source Mass Flow Controller With Viscous Laminar Flow
The 1152C Vapor Source Mass Flow Controller is a pressure-based measurement and control system designed to meter and control vapor from low vapor pressure liquid and solid sources directly, without the need of a carrier gas. The 1152C consists of a fixed flow element and two capacitance manometers for flow measurement, with a proportioning solenoid control valve for flow control.
-
product
Universal Checkback Standalone System
UCBS
The Universal Checkback Standalone System (UCBS) provides periodic testing of "ON-OFF" carrier sets other than the TC-10B and the UPLC/UPLC-II (which incorporate this same checkback tester internally). The UCBS determines the functionality of the complete channel including the transmitters, receivers and associated coupling equipment. Periodic testing is required for the normally "off" channel, to provide warning of signal deterioration prior to needing it for relaying, The UCBS facilitates automatic testing of the channel at preset intervals. The UCBS is totally field programmable. All programming is done with a computer using the RS232 serial port or limited factory settings with switches on the Checkback module. Front panel LEDs indicate the factory or custom setting applied and the status of alarms.
-
product
In-Process Wafer Inspection System
7945
Chroma 7945 wafer chip inspection system is an automated inspection system for pre and post diced patterned wafers. Change kits enable switching between various applications by allowing different carriers including metal frame or grip ring.
-
product
MIL-STD-1553 & ARINC PMC Interface Card. Supports cPCI/PXI Backplanes
CPCIC3/6-MA4
Alta Data Technologies’ CPCIC3/6-MA4 (PXI Compatible) interface module is a multi-channel, multi-protocol 1553 and ARINC PMC on 3U (PXI Compatible) or 6U carrier card supported by the latest software technologies. This hardware and software package provides increased system performance and reduces integration time.
-
product
Fine Pitch Probes
Fine pitch probes are spring contact probes with pitches between 0.10 / 4mil and 1.00mm / 40mil.In this pitch, direct soldering and the use of mounting receptacles is usually no longer possible. Therefore, almost all fine pitch probes are designed as double-sided spring-loaded contact probes. Fine pitch probes are installed in corresponding test sockets, which enable exact contacting of the test points. Feinmetall fine pitch probes are suitable for common components such as BGA, LGA, QFP, QFN or WLCSP. Precision and 100% quality control characterize these probes.In smaller pitches of 60 – 300µm, carrier needles (beams) are also used.
-
product
PCI/104-Express Quad PCIe MiniCard Carrier
E104-MPE
The PCIe MiniCard carrier provides four PCIe MiniCard sockets on a PCI/104-Express form factor board. All four sockets have PCIe x 1 and USB interfaces and support full size and half size PCIe MiniCard modules.
-
product
Cellular Communications
To make it easy for you, Campbell Scientific offers complete cellular connectivity solutions. Data loggers are available with integrated modems and stand-alone cellular gateways that are all certified by carriers across the globe, including Verizon, AT&T, and T-Mobile.
-
product
Industry Pack I/O Products
Acromag IndustryPack mezzanine IP modules deliver maximum I/O density when used with industry-standard IP carrier cards for VME, PCI, CompactPCI or PCI Express. These plug-in Industry Pack modules give you mix-and-match flexibility and high channel density to save your valuable card slots. Combining different IP types on one carrier simplifies the design of a low-cost, custom I/O board.
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for One M.2 PCIe SSD Module
SKU-086-31
The Squid PCI Express Carrier board for M.2 SSD module is the smallest carrier board on the market. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows vertical installation in any 1U servers or appliances.
-
product
PMC Carrier for PCI Card Interface
TPCI270
The TPCI270 is a standard 33 MHz, 32 bit PCI carrier for a single PMC Card. Itprovides PMC front I/O and PMC P14 rear I/O. This PMC to PCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in standard PCI systems.
-
product
Single Processor COMe Carrier Board
NS11001
LinkedHope Intelligent Technologies Co.,Ltd.
NS11001 is a single processor COMe carrier board based on the Intel® AtomTM N270 platform.The board size is: 200mm x 184mm.NS11001 supports both PCI bus and ISA bus in order to be compatible with customers’ legacy peripheral interface cards like MVB. In addition, it consists of a 10.4-inch external TTL LCD panel and a matrix keyboard interface.Bined with COMe module, NS11001 embedded platform using Intel mobile processor N270, 945GSE + ICH7M chipset, and the maximum power consumption at full load is 10W.The system displays interface provides up to 1600 * 1200 resolution display output, and has a variety of interfaces such as Gigabit Ethernet, UART, USB, PATA, etc.NS11001 supports extended working temperature and can be used in harsh environment.
-
product
ATCA Rear Transition Module
ART104
The ART104 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC104 carrier board. The ART104 is a passive RTM that allows for Management 10/100Mbit Ethernet, Management RS-232 serial interface and PCIe x4 lanes for expansion.
-
product
200 kHz dual domain audio analyzer
SR1
Stanford Research Systems, Inc.
SR1 Dual-Domain Audio Analyzer is a stand-alone instrument that delivers cutting edge performance in a wide variety of audio measurements. With a versatile high-performance generator, an array of analyzers that operate symmetrically in both the analog and digital domains, and digital audio carrier measurements at sampling rates up to 192 kHz, SR1 is the right choice for the most demanding analog and digital audio applications.
