Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
LXI Microwave Multiplexer, SP6T, 4-Bank, 18GHz, 50Ω, SMA
60-800-104
Microwave Multiplexer
Our 60-800-104 is a 4 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-051-HI
Programmable Resistor Module
The 40-230-051-HI (PXI) and 42-230-051-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 2.95MΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Legendary Calibration Oscillator
LCO Series 3.5” x 2.5” x 0.6”
-
*Connectorized Package *Low Output Power Variation (±0.05 dB)*Output Power to +10 dBm Available *Optional Internal Reference
-
Product
9050 - 50 Module, 2-Tier Solution
-
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
-
Product
Integrated Potentiostat and Multiplexer
EmStatMUX8
-
Based upon the EmStat range, there are two types of multiplexers to suit most types of sensor array work. The MUX8 is the most flexible offering the ability to connect arrays made of up to eight working electrodes in two or three electrode cell types and chips sharing a reference electrode and/or counter electrode. The MUX16 is suitable for sensor arrays or chips with sixteen working electrodes all sharing a RE and/or a CE. Both instruments are suitable for laminated layer corrosion analysis.The potentiostat is controlled and powered by USB and is used with PSTrace allowing for simultaneous sampling of each channel at a rate of 25 ms/channel. Standard packaging includes a shielded cable with connections for a working, a counter and a reference electrode by means of 2 mm banana connectors and mini-crocodile clips, a stripped end, Dsub-37 terminated flat cable and a USB cable. To make connections to chips simpler the Connection Terminal is an optional extra providing clearly marked screw terminals to the electrodes and can be directly joined to the ESMUX via their D-Sub connectors.
-
Product
Point Universal Cable/Harness Tester
CableJoG 1024
-
The CableJoG 512 and CabeJoG 512 Plus provide a flexible testing system to suit individual customer requirements. The CableJoG 512 and CableJoG Plus 512 can test up to 1024 individual connections of all manufacturers of connectors.
-
Product
PXI/PXIe Power Relay Module,5 Amp, 50-pin SGMC Connectors
40-153-002-HI
Relay
The 40/42-153-002-HI is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
Product
8 Connector-Hole Back Extension
9401-BE
-
Semi-enclosed version of the cabling "doghouse" for the Hawk/PC chassis with rear panel punched to accommodate 8 50/37 pin d-sub connectors. Space is provided to mount the standard DG-style 100 pin edge connector paddles.
-
Product
MMW Field Sensors
ITS-9050
-
The Innovative Technical Systems ITS-9050 Detector is a sensitive, harmonic mixing detector designed to measure millimeter-wave free-space radiation. It is ideal for measuring radiation patterns of antennas inboth the near and far-field. The ITS-9050 employs a free-running dielectric resonator oscillator (DRO) and an integrated harmonic mixer with a waveguide RF input that either connects directly to a circuit under test or to an antenna for radiation detection. The resulting IF is amplified and detected by an IF log-detector that drives a front panel LCD voltmeter to provide an indication of signal strength. A DC output voltage from the log detector is available on a BNC connector to drive external data acquisition instrumentation. Also, a sample of the IF output is provided for measurement on a spectrum analyzer.
-
Product
Drive-Thru Feature, GTE 10.00p
K8218B
-
The DriveThru feature enables the test development software to test integrated circuits or connectors when there are no test points assigned between the resistor and the device.
-
Product
Dual Nav/Comm Test Panel
TA-155
-
The Best Dual Nav/Comm Test Panel on the market today. This panel is designed to test the KX155/155A and KX165/165A radios specifically as well as others and will allow by the book testing of these units. The panel includes specific switching for testing the intercom features, providing unit configuration and audio isolation as required. This panel also incudes basic provisions to run a second Nav/Comm using the long time standard 8 pin octal connector. Monitoring of either current or voltage to either radio is also provided. Integrated or stand alone testing of your OBS or converter indicators is provided as well as the required test jacks. Click on picture for larger view.
-
Product
Azure Data Factory
-
A fully managed, serverless data integration solution for ingesting, preparing, and transforming all your data at scale. Integrate all your data with Azure Data Factory—a fully managed, serverless data integration service. Visually integrate data sources with more than 90 built-in, maintenance-free connectors at no added cost. Easily construct ETL and ELT processes code-free in an intuitive environment or write your own code. Then deliver integrated data to Azure Synapse Analytics to unlock business insights.
-
Product
Force Sensors
-
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 1m, 250 Port
A500RMR-05F050D4B100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Tinned Ends, 2m, HV
A009DF4-T-HA200
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
68-Pin VHDCI Cable Assembly, Male to Unterminated With Cut Ends, 1m
A068VMR-C-6C100
Cable Assembly
The male cable assembly is suited for direct connection to various products using the 68 Way VHDCI connector.
-
Product
8-Channel Relay Output Board With Housing for Mounting on a DIN Rail
PX8500-G
-
The PX8500 is an external 8-channel relay board for the connection of digital output boards. It can be cascaded in 16, 24 and 32 relays and is intended for mounting on DIN supporting rails. The board provides a convenient interface between an industrialprocess and the SUB-D connectors on ADDI-DATA boards. The change-over contacts of the relay are controlled through 24 V signals. The 24 V voltage supply is protected through varistors and transil diodes. The board is intended for the use with 220 V supply. The creeping distance (acc. to DIN VDE0110) and the connector cross sections allows high-power switching (up to 2,500 VA).
-
Product
LXI Microwave Multiplexer, SP6T, 7-Bank, 67GHz, 50Ω, SMA-1.85
60-800-807
Microwave Multiplexer
Our 60-800-807 is a 7 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 7-Bank 18GHz SMA
60-802-207
Multiplexer Module
The 60-802-206 is a 4-channel, 6-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
3-Pin Power D-Type Cable, Male to Unterminated, Cut Ends, 2m
40-972-403-2m-MU
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Coaxial Termination, DC to 50 GHz
85138A
-
The Keysight 85138A is a precision, low-reflection dc to 50 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard. The Keysight 85138A has a 2.4 mm male connector.
-
Product
PXI Single 24:1 High Voltage Power MUX
40-331-001
Multiplexer Module
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
Net Series 1 Gigabit Ethernet
-
The standard NET Series design uses rugged stainless steel connector bodies with a naval bronze engaging nut. The use of metal key and Acme threads on the mating interface allows for easy mating and un-mating of the connectors, no matter where they are located. In addition to the contact spacing, which is optimized for this application, one of the keys to achieving the 1 Gbit/s transmission rates is in the unique terminations for both the cable and bulkhead connectors. These cable terminations can be performed at a number of the Teledyne Oil & Gas worldwide manufacturing and support locations.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-022
Multiplexer Module
The 40/42-860A-022 is a PXI/PXIe dual insert/bypass switch with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Testing, Inspecting & Cleaning Kit
KI-TK033
-
850/1300 nm source & power meter, inspection microscope, cleaning materials. Interchangeable MPO, SC, LC connectors
-
Product
M-Module Carrier for PCIbus
i2001
-
The i2001 M-module Carrier for PCI bus implements a PCI bus gateway to the M-module interface. One M-module mounting socket is provided by this carrier. The M-module I/O connector is accessible through the PCI card bracket. The M-module interface of the i2001 complies to the M-module Specification ANSI/VITA 12-1996. The interface features A8, A24, D16 and D32 access types.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 50 GHz, 50 Ω, SMA-2.4, Failsafe
42-780B-552
Relay
The 40-780B-552 (PXI) and 42-780B-552 (PXIe) are dual failsafe SPDT 50 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
LXI Microwave Multiplexer, SP6T, 2-Bank, 67GHz, 50Ω, SMA-1.85
60-800-802
Microwave Multiplexer
Our 60-800-802 is a 2 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 1 Amp, 2m, 500 Port
A500RMR-C-1B200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
