Conductivity
-
Product
Dopant
-
In semiconductor manufacturing, electrical performance starts with atomic-level control. Dopant technologies make that possible by introducing carefully measured doping constituents that help devices conduct, switch and perform reliably. For precise control of fluxes for Molecular Beam Epitaxy (MBE) dopant constituents, or for gases that do not require thermal cracking, Veeco’s Dopant products are ideal.
-
Product
Circulators
-
To protect a power amplifier in case of bad antenna matching the use of a circulator is recommended. This item conducts the reflected power into an external terminating resistor where it is absorbed. Therefore the power amplifier is protected well because the output stage is always matched correctly.
-
Product
300W to 500W - Single Output
CUS500M1 Series
-
*300W (500W Peak) Convection Cooled*500W with Forced Air*Medical Certifications (2xMOPP)*Class B Conducted and Radiated EMI*Suitable for Class I and Class II installations*Compact 3 x 5 x 1.46" size
-
Product
TIM (Thermal Interface Material) Measurement System
-
Thermal Engineering Associates, Inc.
A system for the measurement of thermal conductivity of a wide range of thermal interface materials - grease, pads, foils, etc. - with a measurement range of of roughly 0.1 to 500W/m-K. (>500W/m-K available on custom basis.)
-
Product
PXI High Density MUX BRIC, 4-Chan, 40-Pole
40-570-211
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Meter With pH Electrode, Conductivity Probe
PC 2700
-
Your all-in-one solution for multi-parameter research work in the lab! The new PC 2700 is accurate, reliable and intuitive with user-friendly functions. Meter comes with a multi-data screen that includes Temperature, electrode status, calibration points, date and time along with your desired measurement parameter
-
Product
VPX Development Systems
-
development system with Backplane Profile BKP6-CEN06-11.2.5-n. Specifically supports OpenVPX and VPX REDI 6U convection or conduction cooled boards and modules.
-
Product
Universal Tensile Testing Machines
-
Dongguan Amade Instruments Technology Co., Ltd
Universal tensile testing machines are testing equipment that are used to conduct mechanical testings of static load, tensile, compression, bending, shearing, tearing, stripping, applied to plastic sheets, pipes, tapes, rubbers, electric wires, springs, sponges, fibers etc. Tensile test is performed to measure and analyze the physical performances of different types of materials and finial products, playing an important role in developing new materials and controlling products quality. From the perspective of function, universal tensile testing(UTM) machine is an omnipotent instrument Just as the name implies. Clamps or fixtures are interchangeable on the basis of different test pieces, enabling various testings to be carried out on one tensile testing instrument. Options of single-column stand or twin-column stand can be available based on the specimen’s tensile/compressive force and dimension. Computerized tensile tester is preferred rather than microprocessor version If users want testing results including curve graphics between time, force and displacement.
-
Product
Silver Ball Matrix Sockets
-
SM Contact is a unique contact that has precise silver balls held together by a proprietary conductive formulation. These conductive columns (diameter optimized for 50 ohm impedance) are suspended in a non-conductive flexible elastomer substrate with a patented solid core for enhanced durability and reliable performance over time, temperature and cycles. This flexible substrate is very compliant and resilient and enables the conductive columns to revert back to original shape when the force is removed. Solutions are available for 0.25mm to 1.27mm LGA, BGA, QFN, CSP, POP, WLP and other packages. The silver ball matrix contact technology is also available with a protective plunger matrix (a gold plated copper cylinder) that sits on top of the conductive columns. This plunger matrix protects the conductive column from contamination from various solder ball interfaces. A quickly replaceable plunger matrix enables minimal downtime during final production test. The product family code for this line of sockets is SMP.
-
Product
PMC & ccPMC Card
EXC-1553PMC/Px(S)
-
MIL-STD-1553, conduction cooled, interface board. Supports up to 4 multi function channels.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are multi-channel (up to four) MIL-STD-1553 interface boards for PCI Mezzanine Card compatible computers.
-
Product
Tabletop Light Fastness Tester
TF419
-
TESTEX Testing Equipment Systems Ltd.
Tabletop Light Fastness Tester is a powerful xenon instrument with affordable price for conducting accelerated tests of light fastness and photo stability test.
-
Product
Light/Laser Flash Analyzers
-
Light or laser flash is a measurement technique used to determine the thermal diffusivity, thermal conductivity, and specific heat capacity of materials. Light flash measurements are essential for characterizing the heat transfer and storage properties of a variety of materials, whether the sample of interest is expected to insulate, conduct, or simply withstand temperature changes.
-
Product
Pressure Mapping
TIRESCAN
-
Complete pressure imaging system for conducting tire tread analysis.
-
Product
Conductivity / TDS / Salinity
-
The amount of mineral and salt impurities in the water is called total dissolved solids (TDS). TDS shows how many units of impurities there are for one million units of water. One way to measure impurities in water is to measure the electric conductivity of water. Absolutely pure water is a poor conductor of electricity. Water shows significant conductivity when dissolved salts are present. Over most ranges, the amount of conductivity is directly proportional to the amount of salts dissolved in the water or Salinity.
-
Product
Conductivity and Temperature Water Pocket Meter
LAQUAtwin EC-22
-
The only pocket meter that directly measures conductivity in 0.12ml sample. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the sensor. This procedure saves you time and prevents wasting your precious sample.
-
Product
TDS Meter For The Pool & Spa Industry
PoolMeter™
-
The “dual” range PoolMeter™ is the perfect instrument for the measurement and control of pools and spas. It is a simple and compact pool water analysis instrument operating on the principal of electrical conductivity.
-
Product
Type 12R1 Family of 19" Rackmount Chassis Platforms, Reduced Weight, Rugged
12R1
-
The Type 12R1 family is a 19" rackmount chassis platform that is rugged yet lighter weight than the sturdier Type 12R2 platform. The chemical conversion coating provides corrosion protection and electrical conductivity. The rear evacuation cooling system uses high CFM blowers to remove the heat generated by the board payloads.
-
Product
Voltage Detector
LV-1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Using conductive rubber tip, free from short circuit. With slip stopper for the safety use.
-
Product
ESD Ground Point
EGP-020
-
The EGP-020 ESD Ground Point is a convenient mechanical socket that can be mounted on to any equipment frame for equal-potential bonding to the equipment. The 4 mm socket is not insulated, made of lathed brass, nickel-plated, for use as grounding socket.The EGP-020 is designed to be mounted on an unpainted conductive surface.
-
Product
Visible Spectrophotometer
Go Direct®
-
Vernier Software & Technology, LLC
The Go Direct® Visible Spectrophotometer is a robust and accurate portable visible light spectrophotometer that connects easily to your device via Bluetooth® wireless technology or USB to conduct Beer’s law experiments, kinetic or equilibrium studies of absorbance, or emission spectrum analysis.
-
Product
Application Specific LC Systems
Co-Sense for LC-MS
-
In LC-MS, there are various factors which may preclude the applicability of HPLC with MS analysis, including the interference associated with non-volatile buffers often used in HPLC. Therefore, tedious procedures are adopted, in which separation and collection is conducted by HPLC, and after desalting and other processing, MS measurement is performed.
-
Product
EMC Testing Services
-
Our sophisticated technology can meet the diversified needs of customers. Component Tests: Immunity, Radiated Immunity, ALSE, TEM cell, Bulk Current Injection, Stripline, Conducted Immunity, Transient Immunity, Power Supply Variations, Electrostatic Discharge Emissions, Radiated Emissions, Conducted Emissions, Transient Emissions. Vehicle Tests - Radiated Immunity, Radiated Emissions.
-
Product
Digital Thickness Gauges Ultrasonic Coating Thickness Meter
HC-220
-
Shenzhen Chuangxin Instruments Co., Ltd.
HC series of coating thickness gauge is a portable thickness gauge with eddy current thickness method and electromagnetic thickness method. It can be used to quickly and accurately measure the thickness of coating or cladding material withoutdamaging it. As an essential instrument for professional material protection, this coating thickness gauge is widely used in manufacturing industry, metal processing industry, chemical industry and commodities inspection etc. ,both in the laboratory and in the engineering field. It can measure the thickness ofnonmagnetic layer on magnetic metal substrate condition (such as steel, iron, alloy and hard magnetic steel, etc.) and the thickness of conductive layer on nonmagnetic metal substrate condition (such as rubber, paint, plastic, anodic oxidation film, etc.).
-
Product
EMC Subracks
101.1/10/11
-
VECTOR Electronics and Technology, Inc.
VectorPak™ EMC Rugged subracks for heavy duty applications where a high resistance to shock and vibration is required. Its features include heavy two-screw fixing extrusions, 2.5mm thick side panels / rack flanges and conductive finish throughout.
-
Product
PXI 3A Power MUX BRIC, 16-Channel, 12-Pole
40-571-304
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Conductivity Meters
-
Conductivity meter measures the amount of electric current or conductivity in solution.A conductivity meter measures the health status of the natural water body.It is very useful in the field of water.
-
Product
Precision Pots Multiturn
-
Precision potentiometers are designed for control applications where accuracy and high-reliability is important. These devices are available in conductive plastic, wirewound or Hybritron® element types, and in various sizes. Both single-turn and multiturn models are available. Typical applications include measuring linear distance, angles or rotations in production equipment, industrial test and measurement equipment, and medical equipment.
-
Product
Synthesisers
Immunity
-
The Laplace Synthesisers cover both conducted and radiated RF immunity test requirements. The frequency coverage extends from 100KHz to 500MHz for conducted tests (RFIC-4-6) and 30MHz – 6GHz for radiated tests (RF3000/RF6000). They are all controlled from the users PC via a USB link, and powerful Windows software is included to enable the user to control all the parameters of the test, to monitor the test in progress, and to view the results.
-
Product
Oxygen / Nitrogen Analyzer
ELEMENTRAC ON‑p 2
-
The new ELEMENTRAC ON-p 2 is a powerful and robust elemental analyzer for measurement of oxygen and nitrogen concentrations in inorganic materials like steel, iron, copper or ceramics. The highly sensitive NDIR and thermal conductivity detectors reliably detect element concentrations from low ppm content to high percentages.
-
Product
Gem Testers
-
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
A diamond tester is a portable device used to check the authenticity of diamonds and test materials for their thermal and electrical conductivity. It can accurately indicate if the stone is a real diamond based on the gem's physical properties.





























