Conductivity
-
Product
Battery Condition Analyzer
BT-301
-
Kongter Test & Measurement Co., Limited
The BT-301 Battery Condition Anlayzer is updated battery handheld tester which is very effective and economical battery management device for testing battery internal resistance (or conductance) and voltage. It helps you eliminate weak batteries to ensure performance of your battery systems.
-
Product
Detailed Hydrocarbon Analysis
-
The purpose of detailed hydrocarbon analysis (DHA) is to determine the bulk hydrocarbon group type composition (PONA: Paraffins, Olefins, Naphthenes and Aromatics) of gasoline and other spark-ignition engine fuels that contain oxygenate blends (Methanol, ethanol, MTBE, ETBE, and TAME) according to ASTM-D6730. PONA analyte identification is conducted by matching retention indices with normal hydrocarbon paraffins. However, chromatograms obtained in PONA analyses have an extremely large number of peaks and their analytes may be mislabeled. Without accurate and reproducible retention indices, this may result in erroneous PONA ratios. The GC-2030 incorporates an Advanced Flow Controller that enables highly precise flow control, and makes it easy to analyze and identify detailed hydrocarbons. Shimadzu offers DHA analysis conforming to the following methods: ASTM-D5134, ASTM-D6729, ASTM-D6730, and ASTM-D6733.
-
Product
EMI/EMC Testing
-
This type of testing is required for devices, systems, and applications within the military and aerospace industries. Weapons, aircraft, ground and support equipment, electrical, and electronic systems must meet the established requirements.During electromagnetic interference the component's electrical circuit is affected due to either electromagnetic conduction or electromagnetic radiation from an external source.
-
Product
Physical Testing Test
-
Physical Testing by Aero Nav: mechanical, weathering, environmental, immersion, electrical, luminance, thermal analysis, thermal conductivity, water exposure, saltwater exposure, etc.
-
Product
Personal Grounding Tester
PGT120
-
Electronic test apparatus for checking personnel grounding systems such as electrostatic wrist straps and conductive footwear. The unit is equipped with two separate measuring circuits and is therefore capable of checking wrist straps and footwear separately or in parallel. The test result is signaled visually, acoustically (only if error is detected) and via contacts.
-
Product
Liquid Thermal Conductivity Instruments
THW-L1
-
The Transient Hot Wire (THW-L1) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity, thermal diffusivity, and specific heat instrument for measurement of liquids and pastes in accordance with ASTM D7896-19. The THW-L1 was designed with speed and operational simplicity in mind. With a single measurement of 1 second in duration, small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity, thermal diffusivity, and specific heat. The THW-L1 utilizes a non-stationary measurement approach and rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a thin heating wire 40 mm in length and is completely inserted into the sample to be tested.
-
Product
ARINC825 Cards
-
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
Product
PXI 3A Power MUX BRIC, 2-Channel, 24-Pole
40-571-101
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI 3A Power MUX BRIC, 10-Channel, 24-Pole
40-571-105
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Electrical Conductivity Measuring Instrument
SIGMASCOPE® SMP350
-
Handheld instrument for electrical conductivity measurement of non-ferromagnetic metals. The electrical conductivity can be used for determining material properties, like hardness, strength, heat damage and material fatigue of metals. Rapid and simple on-the-spot conductivity measurement of non-ferromagnetic metals acc. to DIN EN 2004-1 and ASTM E 1004.
-
Product
Flocculation Jar Tester
LD-LFC-A11
-
Flocculation Jar TesterLD-LFC-A11is designed to stimulate the process of adding reagents, precipitation, coagulation reaction which occurs in water testing procedures. Features portable, 4 round shaped beakers, each with 0.6 L capacity. With 10 to 1000 rpm speed, this flocculation jar tester conducts synchronous as well as independent running operations. It is used to carry out the jar test during water treatment procedure.
-
Product
Universal Converter
C8000
-
Multi channel converter for all optek photometric and conductivity sensors and electrochemical pH electrodes. Flexible configuration of sensors, measuring ranges, units and product specific setups make the C8000 converter series a powerful device in process monitoring in both conventional and single-use systems.
-
Product
ExactFlat Software
-
ExactFlat enables manufacturers to design, flatten, conduct pattern engineering, nest, cost and create manufacturing and business documentation all on one platform.
-
Product
Capacitors - Polymer
-
Polymer capacitors feature a hight volumetric efficiency that allows smaller devices to have higher capacitance values. Vishay offers polymer capacitors in a variety of surface-mount case sizes for applications such as military, portable consumer, computer/ server, network infrastracture equipment, and many others.Polymer capacitors are constructed with a highly conductive polymer as the cathode system. For the anode, tantanum is used together with tantalum oxide dielectric. This construction gives polymer capacitors all the advantages of traditional tantalum capacitors while reducing equivalent series resistance (ESR) and eliminating manganese dioxide, which is a source of catastrophic failure in tranditional tantalum capacitors.
-
Product
For Conduction Cooled ΜTCA Chassis
UTC003
-
The VadaTech UTC003 is the most feature-rich MCH (MicroTCA Carrier Hub) for the Conduction Cooled μTCA chassis in the market. It’s management software is based on VadaTech’s proven Carrier Manager and Shelf Manager. The MCMC manages the power modules, the two CU (Cooling Units) and up to 12 AMCs within the μTCA chassis. It also interfaces to and manages the on-board fabric interfaces. The module is available with PCIe, SRIO, 10GbE Layer 3 managed, and GbE Layer 2 managed. The UTC003 runs Linux 2.6 on it’s MCMC CPU and is hot-swappable and fully redundant when used in conjunction with a second instance of the module. The firmware is HPM.1 compliant which allows for ease of upgrade. The UTC003 provides Fabric (100 Mhz HCSL) clock to each AMC.
-
Product
Security Testing
-
Security/negative testing is typically conducted during development to highlight how a DUT handles abnormal conditions like very high traffic load, different frame sizes (incl. undersized and oversized frames), framed with different IFG settings, various types of errors and deviation of the signal frequency, as well as various DDoS attacks.
-
Product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
-
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
Product
Open Frame 3U 34HP Chassis
-
An open-frame solution for the open-minded engineer. With moveable rear profiles (up to 2.5mm,) 3U and 6U backplane compatibility options, air or conduction cooling options and the ease of fast and simple backplane interchangeability for fluid transition between VITA and PICMG bus architectures, the Hartmann Open Frame Chassis solution is the tool for customers who need versatility, accessibility and longevity.
-
Product
Thermal needle system thermal resistivity / conductivity measurement
MTN01
-
Hukseflux Thermal Sensors B.V.
The MTN01 Multi-purpose Thermal Needle System allows performing fast measurements of the thermal resistivity or conductivity of soils. It is specifically designed to be reasonably robust, as well as accurate. It is therefore suitable for laboratory as well as field- measurements of soil thermal properties. The sensor is a Non-Steady-State Probe (NSSP), TP07, which is mounted on the Insertion Tool, IT02. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
Non-steady-state probe for thermal conductivity measurement
TP02
-
Hukseflux Thermal Sensors B.V.
TP02 is a probe that offers the possibility to perform a practical and fast measurement of the thermal conductivity (or thermal resistivity) of the medium in which it is inserted at the highest accuracy level. It works in compliance with the ASTM D 5334-00, D 5930-97 and IEEE 442-1981 standards. The standard TP02 probe has proven suitability in soils, thermal backfill materials, sediments, foodstuff, powders, sludges, paints, glues and various other materials. The Non-Steady-State Probe (NSSP) measurement method (also known as transient line source, thermal needle, hot needle, heat pulse- and hot wire technique) has the fundamental advantages that it is fast and absolute while the sample size is not critical. Hukseflux is specialised in NSSP design. Special models have been developed for in-situ field experiments. For permanent installation in soils, a dedicated model, TP01, is available. TP02 has been designed and tested in collaboration with the Applied Physics Group of Wageningen University.
-
Product
Three-Parameter Water Quality Analyzer (three-parameter water level gauge)
HR8833
-
HighReach Measuring & Controlling System Co.,Ltd
The HR8833 integrated pressure water level gauge is a three-parameter (water level, water temperature, conductivity) measurement product. It can be used with digital atmospheric pressure meter. It can be externally powered and self-powered by internal battery. It can be The product includes a water level sensor, a temperature sensor and a conductivity sensor, a built-in large-capacity non-volatile memory and a high-capacity long-life lithium battery, For three-parameter hydrological parameter measurement of surface water, groundwater and marine environment.
-
Product
SpaceWire Conformance Tester
313
-
The SpaceWire Conformance Tester connects to a SpaceWire device and, through the host software, executes a variety of tests to check the unit under test’s (UUT) compliance to the SpaceWire Standard. Over 55 tests are conducted across the following levels:
-
Product
Seismic Acquistion QC Serivices
-
Overall data quality / cost monitoring / safety / daily reporting to client. Verif-i provides technical and operational programme assurances for seismic surveys conducted for the company. The lead acquisition QC on-board/on-crew the seismic vessel/block accepts or rejects data on behalf of the company. Our representative will assist the contractor in fulfilling the technical and operational requirements of the seismic programme and report on crew activities.
-
Product
Storage Modules
-
Elma offers the most complete line of storage modules in the embedded computing industry. Board sizes include 3 U, 6 U, mezzanine and small form factors in VPX, VME, CompactPCI, PMC and XMC standards. Environmental capabilities address commercial and rugged applications with SSDs (solid state drives) and rotating drives (HDD) and surface mount NAND flash. Choose from features including RAID, front panel removability, high capacity conduction cooled mezzanine storage, secure erasure or write protection.
-
Product
150 kHz-230 MHz Broadband Power Amplifiers
-
Output power up to 80W for standard conducted immunity testing. Our 150 kHz-230 MHz amplifier range covers output power ranging from 20 W to 80 W.
-
Product
Guardian Hipot Analyzer
19055
-
Chroma Systems Solutions, Inc.
Hipot or dielectric withstand testing instruments manufactured by Chroma are used for conducting electrical safety tests on electrical components and products to make certain they are in compliance with IEC, UL, TUV, CSA, EN and other electrical safety requirements. In addition, these instruments are designed for general product or component testing as well as complex medical safety testing (60601-1) ensuring human safety and product reliability.
-
Product
USB 2.0 Interface Module
-
USB 2.0 modules for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the USB 2.0 link untouched.
-
Product
Electrical Conductivity Measuring Instrument
SIGMASCOPE® SMP350
-
Compact handheld device for measuring the electrical conductivity of non-ferrous metals.
-
Product
Battery Chargers
-
DC Battery ChargersStep-Up & Step-Down DC Source Chargers and Equalizers These units provide up to 600 watts to charge a 12V or 24 V battery systems (1 or 2 banks) from a 12, 24, 32 or 36 volt source. The single-board design incorporates state-of-the-art switch mode technology for unmatched efficiency and ultra-quiet operation. Multiple stages of filtering reduce radiated or conducted noise to very low levels. All Series are capable of charging up to two independent banks of batteries.
-
Product
EMC Testing
-
Does your product send or receive electromagnetic data? This can be analyzed using various tests. We investigate the interference immunity and emitted interference of simple electrical devices and complex machinery. Our EMC measurements and tests conducted in accordance with standards recognize all activity in the electromagnetic field and ascertain how immune to interference a piece of equipment is. We will also offer guidance on optimizing the product in terms of its EMC properties during the development phase.




























