Fuel Injection
-
product
COMMON RAIL Electronic Diesel Injection Analyzer
EDIA-PRO
The EDIA-PRO is an enhanced version of the proven EDIA-5 analyzer. To meet expectations of our customers we created a system for automatic evaluation of injection system parameters based on measured waveforms. This makes the diagnosis easier and faster. Additional possibility of fast evaluation of cylinder compression and ability to check starting performance along with control valve measurement mode are perfect complement to diagnostic capabilities of EDIA device.
-
product
Plastic Injection Molding
Astronics supports world-class OEMs with tight tolerance moldings using highly-engineered aerospace-grade and structural resins.
-
product
Primary Injection Test System
HAOMAI Electric Test Equipment Co., Ltd.
Primary injection testing is suitable for testing over-current trip relays attached to a circuit breaker.
-
product
20Hz Injection Kit Monitoring System
Signals & Systems India Private Limited
The Display used to monitor the 20Hz and 50Hz current passing through NGT transformer. This could help to monitor the stator earth fault and could record the current every minute. The current shall be displayed in milliamps for both 20Hz and 50Hz. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. The current can be measured using clamp-on CT which would be clamped between load resistor and NGT. It gives an indication of the current values are lower or higher than the set threshold.
-
product
Fuel Flow Measurement Systems
FQ Series
Measuring a vehicle’s fuel flow requires a precise system which can run stationary and transient tests. It must also be able to offer high reproducibility and run cycle measurements under real operational conditions, including WLTP. Our FQ Series of fuel flow measurement systems offers a highly precise method of measuring various fuel types, and covers the full range from small engines (incl. single-cylinder research engines) up to heavy-duty engines with up to 5000 kW.
-
product
Secondary Current Injection Test Trolley
SCR ELEKTRONIKS have developed SECONDARY CURRENT INJECTION TEST TROLLEY for Switchgear items, CT manufacturer and where three phase current application is called for. It is low Voltage, 3 phase Current source with control circuitry, digital read out for test current and trip time measurement. We can select different CT ranges for each phase independently and adjust the current as per the required test Current.
-
product
Measuring And Inspection Systems For Extrusion, Injection Molding & Calendering Of Plastics And Films
Measuring and inspection systems from Micro-Epsilon are used in the plastics processing industry in order to ensure efficient production.
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
PEM Fuel Cell
48 Volt 5kW
It is the aim of CellCare Technologies to continually introduce new technology that can provide significant benefits over existing solutions in specific applications. Fuel cellThe latest introduction to the product portfolio is a 5kW PEM (Proton Exchange Membrane) based hydrogen fuel cell, designed to replace 48V standby batteries within remote telecoms sites, satellite base stations, ISP base stations, uplink facilities and weather data collection sites. This technology provides instant power with no hazardous waste, zero emissions, extended autonomy and a guaranteed lifetime with minimal maintenance.
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
Primary Current Injection Test Sets
Our primary current injection test sets cover from 750A through to 6000A. Available in single phase, testing applications include testing and timing of under and over current relays, circuit breakers and CT ratio testing.
-
product
TriRaptor Three-phase High Current Injection
The TriRaptor is the only really portable three-phase injector in the market providing stabilized current in the range of 3000 A and beyond. It has been designed with the same ergonomics and performance characteristics found in the popular Raptor system, so it is really easy to use and can be transported by a single person in a regular vehicle.
-
product
Injection Pump Test Bench
Nanyang NanTai Experimental Equipment Co.,ltd
It adopts advanced frequency conversion technology and digital technology with automatic and manualdouble control for the rotation speed, temperature and count.Equipped with displacement sensor, it can test different kinds of mechanical fuel
-
product
Track (Oval)type ZCT Sensor／Through Hole type ZCT/CT Sensor／Injection CT Sensor
Track Type ZCT Sensor
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High accurate track(Oval) type ZCT sensor*Through hole type
-
product
Hydrogen Fuel Cell
Honeywell Aerospace Technologies
Honeywell has a decades-long history of innovation in power generation for all kinds of aerospace and defense applications, which was further strengthened by the 2020 acquisition of Ballard Unmanned Systems, a global leader in fuel cell technologies for unmanned aerial vehicles (UAVs).
-
product
High-Precision Fuel Flow Measurement System
It enables to keep the temperature fluctuation of the circulation flow path in the system within ±0.2 °C (for 1 minute), which achieves stable fuel flow rate measurement.
-
product
Primary Current Injection
PCI-600
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers.
-
product
Current Injection
K&S Engineering and Scientific Ltd
The outputs are continuously variable from zero and are all isolated. The current outputs can be used at twice their continuous rated current on a 25% duty cycle with a maximum ON time of 5 minutes.
-
product
Fuel Pressure Tester Kit
FIT500
Performs running, residual, rail and flow rate pressure tests.Professional dual scale gauge reads 0-100psi and 0-700 kPa with relief valve and fuel discharge hose and protective rubber boot.
-
product
Single Phase Secondary Injection Test Set
T200A
T200A Single Phase Relay Testing Kit is the best universal secondary injection test set for engineers who need to do all single phase relay test and other basic primary testing which may require single phase long-term high current injection.
-
product
Track (Oval)type ZCT Sensor／Through Hole type ZCT/CT Sensor／Injection CT Sensor
INJ-34
MULTI MEASURING INSTRUMENTS Co., Ltd.
Track (Oval)type ZCT Sensor／Through Hole type ZCT/CT Sensor／Injection CT Sensor
-
product
Secondary Current Injection Test Sets
Our range of units covers applications up to 200A and includes single phase and three phase units with applications for testing and timing of IDMT relays, thermal overloads, MCB’s and auto-reclosers.
-
product
Secondary Injection Test Set
PTE-100-C Plus
In the Pro version this voltage source incorporates a dedicated LCD display and its own BUS-PTE connection that make the operation easier and enable it to be used also with other sets in the PTE range.
-
product
Air-to-Fuel Ratio Analyzer
MEXA-730λ
Previously MEXA-700λII used know-how and ingenuity gathered from HORIBA air-to-fuel ratio measurement technologies used worldwide, to provide the highest level of performance.The MEXA-730λ adopts this performance and adds original design for enhanced visibility and operation.A new sensor coefficient data memory function makes it possible to restore back-up data, providing faster start-up times and saving valuable operation time.This enhanced device will meet your multiple testing requirements covering applications from, lab analysis of air-to-fuel ratio, excess air ratio and oxygen concentration, to on-board real time measurement.
-
product
Fuel Density Meter
FD-5110
By connecting with the FM-3100 Digital Flow Meter, the FD-5110 Fuel Density Meter can measure temperature and density data in real time. In addition, the FP series Volumetric Flow Detectors with wide range ability and the FD-5110 are the best choice for achieving the accurate mass flow measurement.
-
product
Large Current 1000A Primary Current Injection Test Set
TEST-901
Beijing GFUVE Electronics Co.,Ltd.
TEST-901 primary current injection test set adopts ARM Chip to control its output process and large capacity of toroidal transformers. It is equipped with LCD display and current meter; it can show primary current value, second current value, turn ratio and the action time. Packing is used as aluminum alloy body with PC panel. TEST-901 is mainly applied to CT turn ratio testing in the power system and contact resistance test which need large current.
-
product
Vacuum and Fuel Pump Tester
DVG1
Suitable for testing and fault finding the following in petrol engines including: Spark misfires; poor engine compression; weak/rich mixture; ignition over advanced/retarded; inlet manifold and carburettor air leaks; incorrect valve timing; poor fuel economy; balancing carburettors; turbo boost gauge; fuel pump testingDisplay packed.
-
product
Epoxy Injecting Machine - EIM-280
Shanghai Fibretool Technology Co.,Ltd.
1, Injecting Epoxy Adhesive into ceramic ferrules for fiber optic connectors.2, High Accuracy to control epoxy dosage.3, Easy to adjust output pressure and injecting time.4, With hand touch switch and foot switch.5, Compact for production line.
-
product
Track (Oval)type ZCT Sensor／Through Hole type ZCT/CT Sensor／Injection CT Sensor
Round Type CT Sensor
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Round type CT sensor*Through hole type
-
product
SpectrOil M/F-W Fuel Analyzer
SpectrOil M
The SpectrOil M/F-W is a compact, rugged and easy to use fuel analysis spectrometer. It is designed specifically for the analysis of ash-forming contaminants in fuel such as sodium, potassium and vanadium that cause corrosion or deposits at turbine operating temperatures. It measures trace quantities of dissolved or suspended contaminant particles in a fuel sample using the time-tested and reliable rotating disc electrode (RDE) technique.
