Memory Test Systems
-
Product
Flexible Cable, 2.4 Mm To 3.5 Mm
85134H
-
The Keysight 85134H is a 62.9 cm (24.75 in) long1 flexible cable with a 2.4 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.31 * sqrt (f) + 0.2 (where f is frequency is GHz) for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 2.5 inch radius. Stability1 of the Keysight 85134H is less than 0.12 dB and phase is less than 0.13o * f + 0.5o, (where f is frequency in GHz).
-
Product
Laser Diode Reliability Burn-In / Life-Test System
58602
-
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
Product
16GB ECC SO-DDR5-5600 2GX8 1.1V SAM
AQD-SD5V16GE56-SB
-
SAM Original Chip, Anti-sulfuration, PCB: 30μ gold finger. Independent Power Management IC build-in, ECC function support.
-
Product
Mezzanine System
5081
-
The 5081 provides four channels of 12 bit digital to analog voltage output, with multiple single ended output ranges. Each channel is software selectable for 0 to +5V, 0 to +10V, +/-2.5V, +/-5V, +/-10V or -2.5 to 7.5V ranges. The outputs reset to 0.0 volts on power up.
-
Product
16GB DDR5-5600 2GX8 1.1V SAM
AQD-D5V16GN56-SB
-
SAM Original Chip, PCB: 30μ gold finger, Anti-sulfuration, On-die ECC for Enhanced RAS, Operating Temperature: 0°C ~ 85°C.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131G
-
The Keysight 85131G is a 53 cm (21 in) long1 semi-rigid cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 4 inch radius. Stability1 of the Keysight 85131G is 0.06 dB and phase is 0.16o * f + 0.5o (where f is frequency in GHz).
-
Product
Laser Diode Characterization System
58620
-
The Chroma 58620 Laser Diode Characterization Station is a state-of-the-art full turnkey system specially designed for laser diode testing. Features range from macro inspection of the facet or aperture active area to a full suite of electro-optical parametic tests.
-
Product
Functional Test Trainer System
QT65
-
Qmax Test Technologies Pvt. Ltd.
Functional Test Trainer system, is a test system which can perform various Power- On functional tests of digital devices(ssl/MSI/LSIs and analog devices in the out- circuit and in-E conditions. Unified Library of vast number of devices to effectively test devices in in-circuit as well as out of circuit conditions.
-
Product
EV-DO Analysis Using NI PXI RF Test Instruments
NI-RFmx EV-DO
-
Highly optimized RF measurement experiencePerform physical layer analysis on EV-DO cellular signals including MODACC, ACPR, CHP, OBW, and SEMSimple access to advanced measurement parallelism
-
Product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
-
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
Dielectric Material Test Fixture
16453A
-
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
Hybrid Single Site Test Handler
3110
-
Chroma Hybrid Single Site Test Handler 3110 is a full range ATC (Active Thermal Control) test handler capable of handling device bodies up to 120x120mm with 450kg force load.
-
Product
EBIRST 78-pin D-type To 68-pin Female SCSI Adapter
93-006-222
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
-
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Test Port Adapter Set, 2.4 Mm To 2.4 Mm
85130G
-
The Keysight 85130G test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a NMD-2.4 mm (f) to NMD-2.4 mm (m) adapter and a NMD-2.4 mm (f) to PSC-2.4 mm (f) adapter. The frequency range for these adapters is dc to 50 GHz with a return loss of 23 dB or better.
-
Product
Functional Test System
TS-5040
-
The Keysight TS-5040 Functional Test System is a cost effective, robust and reliable test system that gives you the lowest cost of ownership. In addition, the open architecture Test Exec SL gives you the flexibility to do just about anything you want.
-
Product
Test System for High Volume Production Testing of Integrated Circuits
ETS-364
-
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
Product
FADEC/EEC Test Platform
-
The FADEC/EEC Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of full-authority digital engine control (FADEC) and electronic engine control (EEC) units of both rotary- and fixed-wing airframes. The system simulates one or more turbofan engines, including its sensors and actuators for use with the most sophisticated FADECs and EECs on the market. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
2-Quadrant Source/Measure Unit for Functional Test, 20 V, 1 A or 6 V, 3 A, 20 W
N6782A
-
The Keysight N6782A is a source/measure unit (SMU) designed specifically for advanced functional testing of a device. The ability to modulate the output up to 100 kHz along with capability to source and sink current (2-quadrant operation) makes the N6782A a perfect fit for advanced functional test of a variety of devices such as DC/DC converters, power management units, power amplifiers, and power management ICs. The input stage of the DUT can be stimulated by the fast sourcing and waveform capabilities. While the output stage can be loaded down and measured with the electronic load capabilities, providing a total test solution.
-
Product
Mezzanine System
3564
-
The 3564 is a four channel comparator board with a common mode range of -150V to 150V on the two differential inputs and a DAC per channel to set trigger levels. The high common mode range and DC coupling provides a robust solution to level detection and triggering.
-
Product
PCIe 5.0 Test Platform
PXP-500A
-
The Teledyne LeCroy PXP-500A Test Platform provides a convenient means for testing PCIe 5.0 cards with a self-contained portable and powered passive backplane. The PXP-500A provides power required for both cards under test.
-
Product
Prototyping & Test Consulting Services Solutions
-
Don’t cut corners on the path to quality. We are experts in Design for Test (DFT), Design for Manufacturing (DFM), agile development, prototyping and standards/best practices in many industries. Speak to our prototyping and consulting services experts to ensure you make the right decisions and investments at the start of your project.
-
Product
Wide Temperature Server DIMM
SQR-RD4M
-
Original Hynix IC chip adopted, Wide operating temperature support -25~85oC, Data transfer rate up to 3200 MT/s.
-
Product
Functional Test Fixtures
-
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
Product
Modular Breakout System 37-Pin D-type Plugin Module for 40-293
95-293-001
-
The 95-293-001 Plugin Breakout Module is designed to be fitted to a PXI 40-293 Programmable Resistor Module as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
2m BNC Test Cable
16048D
-
The 16048D test leads extend the measurement port with a 4-terminal pair configuration. It provides a BNC female connector board to allow attachment of user-fabricated test fixtures.
-
Product
Compact Functional Test System
E2230C / TS-5040
-
The Keysight TS-5040 functional test system is a robust, and reliable test system that ensures an economical ownership experience. When coupled with Keysight software such as KS8400A PathWave Test Automation with KS8328A PathWave Test Executive for Manufacturing (PTEM) or TestExec SL with TS-5000 libraries, it provides a streamlined development process and accelerated deployment. The TS-5040 seamlessly integrates into heavily automated production areas. It is a minimalistic one-box solution for automotive and industrial applications that saves valuable rack and floor space.
-
Product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
At-Speed Non-Intrusive Functional Testing
ScanExpress JET
-
Functional circuit board testing presents many challenges that are often costly and time consuming. Most functional tests need to be customized for each design, limiting reusability. This results in software engineers vying for time between development code and test code. Even when functional tests become available, the diagnostic details are often inadequate to give clear visibility on a given problem.ScanExpress JET is a tool designed to overcome these challenges by automating the functional test generation process on CPU–based IEEE-1149.1 compliant circuit boards. Coined JTAG Embedded Test, JET is the preferred method for at-speed, non-intrusive functional testing.
-
Product
Scienlab Charging Discovery System (CDS) – High-Power Series
SL1047A
-
The Scienlab Charging Discovery System – High-Power Series from Keysight enables you to test charging interfaces of electric vehicles (EVs) and EV supply equipment (EVSE) during high-power charging up to 1,500 V DC and ±600 A DC. With the CDS can perform all necessary conformance and interoperability tests according to worldwide charging standards. Our new solution, which features the separate Scienlab Cooling Unit with interchangeable liquid-cooled charging adapters, also enables a high-power upgrade of the SL1040A Scienlab Charging Discovery System - Portable Series.
