Servo
feedback seving to control.
-
-
Product
Servo Vertical Shock Tester
-
HIACC Engineering & Services Pvt. Ltd.
The shock tester is commonly used for the reliability damage test of the electrical & electronic components by simulating an impact environment.
-
Product
3U OpenVPX SOSA™-aligned PWM Servo Motor Drive
68PW1
Servo Motor Drive
The 68PW1 is a 3U OpenVPX SOSA™-aligned (basis, Snapshot 2) single-axis PWM servo motor drive that can be configured with closed loop feedback measurement options including Hall, Resolver/Synchro or Encoder. The PWM drive provides programmable PWM output drive (up to 65 V @ 10 A continuous) from a single +28 VDC input source. Ideally suited for rugged Mil-Aero applications, the 68PW1 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Servo Tester
105
-
Simulates a receiver so you can test your motors and servos without having to use a transmitter and receiver. It can send RC-PWM signal of 1ms to 2 ms in 20ms period. It connects to an ESC via three wires. The servo tester is powered by the BEC in your speed control or by a std 4 cell 5 volt receiver battery
-
Product
Electric Servo Motor Type 4 Face 3 Axis Vibration Tester
-
The electric servomotor type 4-sided 3-axis vibration tester can control 4 vibration tables synchronously or independently by combining 4 independent 3-axis vibration testers.
-
Product
Servo type Accelerometer
-
A motion is sensed by a displacement detector, a current is fed to the coil to get back the pendulum mass to the original position. This current will be proportional to the acceleration, that is converted to an output voltage. The Servo type accelerometer is for the Earthquake Monitoring or measurements of micro tremor on the Civil Engineering Structures because of its higher sensitivity and stability or more accurate phase responses in the lower frequency range than those of other vibration transducers.
-
Product
Servo
-
The Hardware: Drives, Motors, Cables (standard and robotics) – all seamlessly supported by Unitronics’ PLCs, HMIs, & VFDsThe Software:One integrated software for your complete motion application: PLC, HMI, Servo, VFD, and I/O
-
Product
Motion Control Terminal Board for Yaskawa Sigma II Servo Amplifiers
DIN-814PA
Amplifier
This well-designed motion control terminal board is for the users who use Panasonic MINAS A super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
Product
Dual Channel Servo Amp
Servo Amp
-
This is our Dual Channel Servo Amp board that the instrument shop can use for testing HSI's like the 331A-( ) series and others or RMI's. This board is standard in our model TA-1000 HSI tester.
-
Product
Portable Servo Conditioners
PTS-V
-
Bemco PTS-V Portable Servo Conditioners provide a closed loop flow of controlled temperature air or gas to an insulated enclosure or structure. Bemco high pressure gas servo conditioners provide air or gas at up to two atmospheres of pressure to heat exchangers and thermal shrouds. Bemco HPG High Pressure Gas Conditioners are described on a separate page.
-
Product
PWM Servo Motor Drives
Servo Motor Drive
NAI's PWM Servo Motor Drives provide programmable, PWM output drive (up to 65 V @ 10 A continuous) from a single +28 VDC input source and Drives Brushed or Brushless (BLDC) motors. Available in 3U OpenVPX and VME board constructions and specifically designed for rugged defense, industrial, and commercial applications with a -40°C to +85°C operating temperature range, these PWM Servo Motor Drives deliver a COTS solution for embedded motor control applications.
-
Product
High Strength Electro-hydraulic Servo Universal Testing Machine
WAW-H Series
-
Jinan Testing Equipment IE Corporation
WAW-H series Servo-Hydraulic Testing Machine Computerized is suitable for testing tension, compression, bending and shearing strength of various metallic & non-metallic materials. Equipped with the electronics, computer &software packages, it is capable of controlling the test procedures by the predetermined programs. The Servo-Hydraulic Testing Machine Computerized can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The Servo-Hydraulic Testing Machine Computerized is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar, aircraft industry, research institutes, laboratories, calibration institutes etc.WAW-H series Servo-Hydraulic Testing Machine Computerized is suitable for testing tension, compression, bending and shearing strength of various metallic & non-metallic materials. Equipped with the electronics, computer &software packages, it is capable of controlling the test procedures by the predetermined programs. The Servo-Hydraulic Testing Machine Computerized can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The Servo-Hydraulic Testing Machine Computerized is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar, aircraft industry, research institutes, laboratories, calibration institutes etc.
-
Product
Stator Tester
DZ800d/e Series
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical properties test of stators of Y-type three-phase motors, single-phase primary and secondary motors, single0phase multi-speed motors, automobile generators, brushless motors, series excitation motors servo motors, and synchronous motors.
-
Product
Servo Motor ,Precision Linear Stages
PSAXXX-11AS-X
-
Model:PSAXXX-11AS-X Servo Motor ,Precision Linear Stages PSAXXX-11AS-X adopt panasonic 100W or 200W AC servo motor and high level coupler,achieve high resolution,high speed,low vibrate;material is alluminum alloy by special craft; Characteristic ◆ground ball screw ,achieve high postion accuracy ◆import guide ensure straightness and parallel inconjunction with our special craft ◆strict assemble craft and test method, ensure high performance ◆servo-motor and limited swithes design, convenient for choosing controller ◆limited switches ensure safety ◆different size and travels,make products abount ◆hand-wheel achieve hand adjustment
-
Product
Multi-Axis Stage Controller
MS-2000-WK
-
Applied Scientific Instrumentation
*100 MHz Microcontroller for faster command processing and servo control.*Closed-loop DC servo control of up to four motorized axes.*Firmware upgradeable via serial connection.*0-10V DAC for single piezo axis control.*Remembers last position on power down/up.*LCD display shows axes coordinates and status.*"Zero" and "Home" buttons for simple stand-alone operations.*USB or RS232 serial control with baud rates to 115200 Baud.*Compact ergonomic tabletop control unit 6"D x 9"W x 3"H (16 x 23 x 9 cm).
-
Product
Amplifiers
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
Linear Amplifiers
LA Series
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
Solid State Active Synchro Control Differential Transmitter
-
Computer Conversions Corporation
The input is transformer isolated and accuracy applies over the operating temperature range and with +/-10% input amplitude and frequency variations. The operational amplifier outputs are not transformer isolated, and can be driven into external power amplifiers and Scott "T" transformers for 3 wire synchro outputs. A typical application of this series is in a conventional positioning servo system as a complex error processor. The use of the solid state CDX makes possible the design of servo systems that can be digitally programmed by direct computer input to the digital input of the SCDX.
-
Product
Dual Servo Electrical Test Fixture
TA-334001
-
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
Product
Digital Brushless Servo Drives
DA Series
-
The DA series high performance digital servo drives integrates digital position and velocity control with built-in power supplies and the latest in PWM servo amplifier technology. Power range up to 50KVA.
-
Product
Motion Control Board, PCI
APCI-8001-1
-
*Axis control for 1 servo or stepper motor*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders *or SSI absolute encoders
-
Product
Dual Space Electro-hydraulic Servo Universal Testing Machine
WAW-E Series
-
Jinan Testing Equipment IE Corporation
WAW-E series computer control servo-hydraulic testing machine is suitable for testing tension, compression, bending and shearing strength of various metallic & non-metallic materials. Equipped with the electronics, computer &software packages, the servo-hydraulic tester of dual space is capable of controlling the test procedures by the predetermined programs. The computer control servo-hydraulic testing machine can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The servo-hydraulictesting machine is easy to operate and is versatile in the applications of metallurgy industries such as steel mills & alloy, reinforced bar, aircraft manufacturer, research institutes, laboratories, calibration institutes etc.
-
Product
Motor Stator Tester
DZ901
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to precision electrical properties test of stators of y-type three-ohase motors, single-phase motors, hub generators, brushless motors and servo motors.
-
Product
Terminal Board With 100-Pin SCSI-II Connector For General Purpose Servo & Stepper
DIN-825-4P0
Terminal Board
- Supports specific servos & steppers by cable selecting- On-board connector type: 100-pin SCSI-II- Dimensions: 300 mm x 107 mm x 44 mm (W x L x H)
-
Product
Advanced 4-Axis Servo & Stepper Motion Controller with High-Speed Triggering
PCI-8164
Motion Controller
ADLINK PCI-8164/PXI-8164 is an advanced 4-axis motion controller. Compared with the PCI-8132/34 series, PCI-8164/PXI-8164 offers better linear and circular interpolated move and continuous contouring performance-ideal for advanced pulse train motion control solutions and complicated motion and pick-and-place applications.
-
Product
Centralized Motion Controller
Motion Controller
ADLINK‘s pulse train controllers provide comprehensive and application-oriented motion functions for servo and stepper motors through digital signal processing (DSP)-based and Application Specific Integrated Circuit (ASIC)-based two pulse train mode controllers to achieve excellent synchronous motion control and precise positioning suitable for laser engraving, marking and cutting applications in semiconductor, AOI, and conventional manufacturing industries.
-
Product
Controllers
-
Applied Scientific Instrumentation
100 MHz Microcontroller for faster command processing and servo controlClosed-loop DC servo control of up to four motorized axesFirmware upgradeable via serial connection0-10V DAC for single piezo axis controlRemembers last position on power down/upLCD display shows axes coordinates and status“Zero” and “Home” buttons for simple stand-alone operationsUSB or RS232 serial control with baud rates to 115200 BaudCompact ergonomic tabletop control unit 6”D x 9”W x 3”H (16½ x 23 x 9 cm)
-
Product
Erichsen Metal Sheet Testing Machine for FLC, FLD
GBW-600
-
Jinan Testing Equipment IE Corporation
GBW series Erichsen Metal Sheet Testing Machine is designed on the basis of screw universal material testing machine, using the servo motor for highly accurate loading for punching, meanwhile, it is equipped with hydraulic servo control system for pre-tightening/clamping of metal sheet. It is ideal to evaluate the plastic deformation performance and ductility of metal sheet & strip materials. The cupping test for metal sheet thickness range is 0.1mm-5mm, Max. Punching capacity is 600KN, and the pre-tightening/clamping device is with hydraulic servo loading pump for 600kN capacity;
-
Product
Rapid Temperature Change Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is the company capable of offering a series of Rapid ESS Test Chamber,Rapid Temperature Change Test Chamber,Environmental stress screening (ESS) test chamber,Environmental stress screening test chamber,Temperature Change Test ChamberEnergy-saving design: Adopting PID + PWM principle of VRF (refrigerant flow control) technology to achieve low-temperature energy-saving operation (electronic expansion valve according to thermal energy conditions refrigerant flow servo control technology) low temperature working state, the heater does not participate in the work, through PID + The PWM regulates the flow rate and flow direction of the refrigerant, and regulates the three-way flow of the refrigerant pipe, the cold bypass pipe, and the hot bypass pipe to achieve automatic constant temperature to the working chamber. This method can reduce energy consumption by 30% under low temperature conditions.
-
Product
Econo Motion Controllers
DMC-41x3
-
The DMC-41x3 motion controller is one of Galil's latest generation, stand-alone motion controller. Compared with the DMC-21x3 controller, the DMC-41x3 offers the following enhancements: 100BASE-T Ethernet, aux RS232 port, USB port, uncommitted analog inputs, up to 15 MHz encoder frequencies, more program memory, and faster sample frequencies. The DMC-41x3 also accommodates the same stepper and servo motor drives used in the DMC-40x0 series and allows two 4-axis 750 W drives to be installed in the 8-axis controller package. The DMC-41x3 is available as a box-level or card-level motion controller. The unit operates stand-alone or interfaces to a PC with Ethernet 10/100BASE-T, or USB. It includes optically isolated I/O in addition to analog inputs and outputs. The DMC-41x3 controller and drive unit accepts power from a single 20-80 VDC source.
