Diode
See Also: Laser Diode, Zener Diode, Diode Test, Photodiode
-
product
Metra Power Clamp
400A
Metra Power Clamp 1000A/400A measures, calculate and displays important electrical pa-rameters of single phase or three phase power system. It also features Resistance, continuity, diode and non contact voltage detection.
-
product
PXIe-4081, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter
783130-01
PXIe, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter—The PXIe‑4081 is the industry’s most accurate 7½‑digit DMM and provides the measurement capabilities found in two common test instruments: a high-resolution 1,000 V DMM and a digitizer. As a DMM, the PXIe‑4081 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXIe‑4081 can acquire waveforms at sample rates up to 1.8 MS/s.
-
product
DC Power Supplies
SFA Series
AMETEK Programmable Power, Inc.
The SFA family builds on the industry leading Sorensen SGA series to provide a high power current source for laser diode applications. State of the art high power laser diodes require well-regulated current control to avoid catastrophic damage. Under anomalous operating conditions, excessive stored energy in the output circuit of the power supply can result in peak stresses that can permanently damage the device. Providing a constant current regulation mode only, the SFA’s low stored energy output minimizes damage potential for sensitive devices as well as enabling a current slew rate of up to 400 A/msec.
-
product
Tunable Diode Laser Absorption Spectroscopy
5100P TDLAS Transportable
Using tunable diode laser absorption spectroscopy, the 5100P is a transportable, easy-to-use analyzer optimized to measure either water vapor (H2O) or carbon dioxide (CO2) in select gas streams.
-
product
Laser Diode Driver
S-101
LD Driver slot module of FOTS system is an efficient module that is user centered, which can drive various kinds of laser diode for the use of optical signal transmission or light source. The module has a built in LD socket, in which LD of 14 pin butterfly type is installed, which makes it possible for the user to change the LD he or she wants to drive when needed. It is leaded to get rid of the inefficiency of expense, at which various types of expensive united source module needed are purchased. By operating monitoring PD and high-performance processor that are installed inside the module, the output power and temperature of LD can be driven accurately and stably. The laser diodes can be modulated internally in square, sinusoidal, and triangular waves and its output power and temperature can also be maintained the level set by the user. In order to realize the various functions, the efficient and multi-functioned control programs with high speed processor, LCD monitor or GUI for remote control are available.
-
product
Battery Monitor
BAF-M2
Schumacher Electric Corporation
BATTERY MONITOR• Plugs into a 12 volt automotive cigarette lighter receptacle• Allows instant monitoring of battery & charging system voltage• Constant automotive battery and charging system check with a digital readout• LED warning lights alert you when your battery or charging system is not functioning properly• Detects charging input voltage within 0.1 volts variance• Detects problems with the alternator, diode and any variance of more than 0.8 volts• Alerts you once battery drops to 12.0 volts giving you approximately one more hour of run time, depending on the system’s wattage• Digital display indicates electrical voltage of your battery• Mounted display on your car’s dashboard for constant monitoring of your electrical system Contents: (1) Battery Monitor with 12V DC plug
-
product
SP5T RF Pin Diode Switches To 12 GHz
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
product
MATCO TECH MULTIMETER
MD257
*Provides readings for volts, amps and ohms required for automotive electrical system tests as well as diode and continuity tests*Lo-Z ghost voltage buster drains ghost voltages leaving only hard signals on meter readings*Beep-Jack audible warning beeps against improper a-terminal plug in and decreases the risk of damage
-
product
Digitally Controlled Programmable Attenuators
Broadband frequencies ranging from 30 MHz to 40 GHz. High attenuation levels up to 60 dB. PIN diode designs exhibit extremely fast attenuation step switching performance. Attenuation step size ranges from 0.03 dB to 1 dB. Programmable attenuator control bit sizes range from 5 to 10 bits. Models powered and command controlled via 15 pin female Micro-D socket or USB interface.
-
product
Frequency Doublers To 12 GHz
Pulsar Microwave Frequency Doublers utilize Schottky diodes in a bridge configuration to accomplish the frequency doubling. The input frequency operates from 0.2 to 6000 MHz. Frequency Quadruplers are also available using using this topology. Designs are matched to 50 Ohms and are available in a wide variety of package styles, such as plug-in, flatpack, and connectorized housings. Miniature surface mount packages are the most popular style, and are readily available on tape and reel for use in automated assembly applications.
-
product
Double Balanced Mixers From 0.01 To 6000 MHz
A double balanced mixer (DBM) employs the use of a well matched quad-diode ring with two balanced transformers. Because of this, a DBM enjoys the inherent advantage of high port to port isolation. The IF port in Pulsar's DBM design is DC coupled to the diodes.
-
product
Regeneration Station
This equipment is a stand-alone device that enables to coherently regenerate an optical signal allowing long-haul dissemination of an ultra-stable optical frequency reference. Its architecture is based on the heterodyne phase-locking of a narrow spectral width laser diode on the reference signal. The station is equipped with low phase noise optical interferometer that perform a thorough characterization of the phase noise accumulated by the incoming signal, and a compensation system of this phase noise.
-
product
LIMITER P-I-N DIODES FROM 0.7 TO 9.55 GHz
They prevent failure of of input amplifying stage of low-noise receivers with radio pulse power up to 5000 Watt. They can also be applied as seperate units without power supply and acting as controlled switches. This component is very valuable for radar applications because the high power transmitter and extremely sensitive receiver work with a single antenna.
-
product
Autoranging Digital Multimeter
HH2205F
High Accuracy (Basic Accuracy 0.5%). 3-3/4 Jumbo LCD display 4000 count with symbolic signs. Auto Ranging High Voltage test up to 1000V DC and 750V TRMS AC. Higher Current test up to 20A AC/DC. Diode and Continuity check. Measure Resistance up to 40MΩ. Measure Temperature up to 760oC or 1400oF
-
product
Switches-SPST
Macom Technology Solutions Holdings Inc.
At MACOM we offer an extensive collection of switches covering multiple commercial and aerospace and defense markets. Our product portfolio has a broad frequency spectrum from DC to 70 GHz. Our silicon Heterolithic Microwave Integrated Circuit (HMIC) PIN diode process is ideal for high power and broadband switches operating from 50 MHz to 26 GHz. Our AlGaAs PIN diode process can extend the upper frequency range of our switch die beyond 70 GHz and is ideal for instrumentation and radar applications. Our GaAs pHEMT and MESFET technology is ideal for fast switching and low control voltage switches optimized for both narrow band and broadband applications. Our 75 Ohm absorptive switches are designed specifically for demanding CATV, FTTx and DBS Infrastructure and CPE applications.
-
product
Cryocoolers
MT
The MT cooler has been in production since 2003 and is based on the CT cooler design. It was developed for the customer who did not need the lift of the CT cryocooler and wanted size and weight reduction for their application. The MT has been used successfully in applications such as High Temperature Superconductivity (HTS) filters, high altitude balloons, refrigeration, germanium detectors, IR detectors, radio telescopes, laser diode cooling, and research among others. We believe the customer will agree that the CryoTel® MT is the smallest 5W @77K cooler available at an attractive price point with a Mean Time to Failure of over 200,000 hours.
