Response
-
Product
Gross Gamma Screening System
-
The Gross Gamma Screening system is intended for the rapid screening of urine samples for the presence of elevated radioactivity in a post-radiological event scenario. This system allows up to eight urine samples to be counted simultaneously in discretely shielded 3” x 3” NaI Well radiation detectors to quickly identify elevated radioactivity from personnel in the exposed population. This screening process provides critical information to Emergency Response Agencies and is accomplished with minimal operator training.
-
Product
FPGA Impulse Response (FIR) Filter Fo Gage Digitizers
eXpert / Finite Impuls Response (FIR)
-
The onboard FIR Filtering eXpert FPGA DSP feature is a powerful method for removing unwanted signal features (like noise) and emphasizing signal features of interest.
-
Product
Radiometer Spectral sensitivities precisely adapted to the measurement task
UVS-B-T
-
Compared to the spectral response of the UVS-E, the UVS-B-T has a sharper cut-off at the transition from UV-B to UV-A. This feature reduces the UV-A contribution to the radiometer output and permits the highest possible correlation to atmospheric UV-B irradiance.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 2.04k Ohm
50-294-022
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Resistor Module 4-Channel 1R to 127R with SPDT
40-293-112
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Test Contactor
cDragon
-
cDragon™ Test Contactor pin’s thermal design supports fast temperature control response and stabilization for repeatable at temperature testing of devices in a handler environment.The homogenous MEMS elastomer-free multi-beam pin delivers long life and high wear resistance. By design the cDragon’s pin decouples insertion motion from the test-interface-board side of the pin. This eliminates test-interface-board pad wear.
-
Product
McMurdo FastFind - Wrist Lanyard
10-91-060-001A Fast Find 210
-
10-91-060-001A Fast Find 210 - standard model with GPS for extra fast position location Announcing the amazing new McMurdo FastFind Satellite Personal Locator Beacon (PLB): the most compact, waterproof and versatile 406 MHz emergency location beacon available on the market today.The Fast Find is a 406 MHz Personal Location Beacon (PLB) that should be carried by individuals, who are embarking on trips into areas around the world where there is little or no other forms of communication or where other forms of communication are unlikely to work. The Fast Find acts as your personal Emergency Location Beacon, it is your last resort communication to the national and international search and rescue bodies and it should not be misused. The Fast Find is designed as a direct communication, to the 406 MHz Search and Rescue satellite system, its signal indicates that you are in need of urgent response and assistance. The location of a McMurdo Fast Find 210 GPS PLB can be determine to a typical positional accuracy of about +/- 62 metres (0.03 miles) within a few minutes of PLB activation. McMurdo FastFind PLB Manual (.pdf)Its small size belies its rugged construction and powerful output. There is no compromise. Once activated, the distress beacon will send out a signal for help, and continues to transmit for at least 24 hours, at a powerful 5 watt output, ensuring that your call for help gets through whatever the conditions. The pocket sized beacon transmits at the press of a button, to alert search and rescue services to your plight.McMurdo FastFind PLB is an essential piece of life-saving equipment, weighing in at just 5.3 oz (150g) and having the size of an average mobile telephone (actual dimensions being 1.34”/34mm x 1.85”/47mm x L 4.17”/106mm) it will slip into the smallest pocket or backpack compartment. The user can activate it in the most remote locations around the world: on land, at sea or in the air, and can be confident of being able to contact the world’s professional search and rescue services directly if they are to encounter a possibly life-threatening situation.McMurdo FastFind PLB comes equipped with an integral 50-channel GPS system and complies with rigid federal and international standards. It operates on the global COSPAS SARSAT 406MHz search and rescue satellite communication system, so a call for help will be acted upon…and fast. The McMurdo FastFind PLB is subscription FREE and does not rely on any commercial call centers. THE McMurdo FastFind PLB model transmits two signals simultaneously: a global 406 MHz signal and a 121.5MHz local signal. Once activated, McMurdo FastFind PLB’s signals will continue to transmit for at least 24 hours, at a powerful 5 watt output, the 406 MHz transmission ensures that a call for help gets through, no matter what the conditions. McMurdo FastFind PLB also includes a unique flashing SOS LED light to further assist in speeding up the user’s recovery time during night rescues.McMurdo FastFind PLB will operate in temperatures as low as -20°c and its integral battery has a user storage life of 5 years, so there’s no need for frequent battery changes or re-charging.Put a McMurdo FastFind PLB in your pocket, and get found fast.
-
Product
PCI High Density Resistor Card 10-Channel, 8-Bit, 0 To 255 Ohm
50-295A-021-10/8
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Galvanostat and Zero Resistance Ammeter
-
This instrument offers a Potentiostat, Galvanostat and Zero Resistance Ammeter with integrated Frequency Response Analyser and Sweep Generator in one. It is based around a two Amp Potentiostat teamed with a two Amp Zero Resistance Ammeter and can be supplied as - 6 channel, with six sequential channels, 8 channel (eight sequential channels) or 12 channel (twelve sequential channels). Connection to the controlling Windows PC is via a standard RS232 port, optically isolated for full floating operation. The instrument is supplied with a full set of cables and software, user manual and application notes on CD.
-
Product
Wideband True RMS AC Voltmeter
323
-
The Ballantine 323 True RMS analog ac voltmeter uses advanced true rms circuitry to achieve square law response from rugged, fast responding silicon diode detectors with no thermal lag and overload vulnerability inherent in thermocouple devices.
-
Product
Temperature Logger for Thermistor Probe
TGP-4020
-
Loggers with probes can be used to record temperature in awkward to reach areas or applications where a fast time response is required. A versatile range of probes are available for this unit and can measure between -40 to +125C. Like the logger, probes are waterproof to IP68.
-
Product
Special Purpose Instruments
-
The Mechanical Impedance Sensor simultaneously measures an applied, driving-point force and response acceleration of a test structure for determining parameters such as mechanical mobility and mechanical impedance. The unit consists of a precision, shear mode accelerometer and a quartz force sensor in a common housing. Installation is primarily facilitated at the structural excitation points, in series with a stinger and vibration shaker.
-
Product
Radiation Detection & Measurement Products
-
Detect, localize, identify, and measure radioactivity in any scenario. From routine monitoring and surveillance to emergency response situations, our advanced, integrated radiation detection instruments mitigate the threat and keep you safe. Our product portfolio of radiation detection solutions provides comprehensive, real-time monitoring, early warning, and complete information in the palm of your hand, in the work place, and in your neighborhood.
-
Product
Phantom Powered Measurement Microphone System
7052PH
-
The 7052PH Type 1.5TM phantom powered measurement microphone system offers a cost effective solution to acoustic measurements from phantom powered sources. Type 1.5TM - a superior Type 2. Frequency Response: <3 Hz to > 20kHz typ.(capsule). Sensitivity: 22 mV/Pa (-33 dBV/Pa)typ. Dynamic Range (capsule) 1% THD: <20dBA-150dBSPL (Capsule).
-
Product
Temperature Measurement IR Sensors & Detectors
ST60 TO-18
-
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 0.61mm x 0.61mm in a small TO-18 package. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
Fast Response Gas Detector
Leaksurveyor
-
Teledyne Gas & Flame Detection
The GMI Leaksurveyor combines quality, ruggedness and advanced Technology in a user friendly, portable gas detector. The integral fast response and high sensitivity semiconductor sensor enables leakage surveys to be performed and distribution leaks to be quickly found.
-
Product
Wireless Belt-Pack Instrument System
IS400
-
The IS400 Digital Hybrid Wireless system sets new standards for wireless guitar and bass. Flat frequency response, low distortion and compandor-free operation provides the closest thing to using a high-quality instrument cable. The system faithfully reproduces the lowest fundamental from a 5-string bass (low B) at 32Hz up to the very highest overtones and harmonics.
-
Product
Embedded Graphics Solutions
-
Designed to support the heavy technological demand of industrial applications, ADLINK’s embedded GPU solutions incorporate the latest NVIDIA GPU technology to take graphics processing to the next level. ADLINK’s GPUs allow for accelerated rendering, AI inferencing, graphics, and computing performance, all while reducing I/O latency and improving system responsiveness. ADLINK also takes common industrial concerns into consideration, with its embedded MXM GPUs that address size, weight, and power constraints and professional PCI express graphics cards that enhance graphics quality and support high-performance computing applications. Importantly, ADLINK’s embedded GPU solutions are durable and long-lived, able to respond to the demanding needs of the healthcare, manufacturing, logistics, transportation, aerospace, telecommunications, and defense industries over a long period.
-
Product
20 GHz Differential Probe with ProLink Interface
DH20-PL
Interface
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
SMT Surface Mount MEMS High-G Shock Accelerometers
-
Piezoresistive MEMS high-amplitude shock accelerometers represent state-of-the-art industry technology for miniature, high amplitude, DC response acceleration sensors. This series is capable of measuring long duration transient motion as well as responding to and surviving extremely fast rise times, typical of a high-g shock event as found in explosive, gun and impact testing. Both packaged and OEM configurations are offered, to fulfill a variety of installation requirements.
-
Product
Image Sensor/Fingerprint-on-Display Testing
-
Enli Tech provides the most advanced optical and non-destructive inspection technology, which can de-convolute the digital images back to the analog properties, such as quantum efficiency, spectral response, system gain K, Dynamic Range (DR), PRNU, DRNU, Linearity Error LE, and Chief-Ray-Angle (CRA). The testing solution can be applied to CCD and CMOS image sensors in aerospace, defense, and scientific camera field. Image sensor packages that can be tested by Enli Tech’s systems include bare wafers, dies, chips, or camera modules. Our image sensor testers can help users reduce the sensor-modules or camera-modules development time and RD budget.
-
Product
PCI High Density Potentiometer Card 2-Channel, 12-Bit, 0 To 4k Ohm
50-296A-021-2/12
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Pocket Network Tester
LinkSprinter®
-
The LinkSprinter Pocket Network Tester verifies the functionality of copper Ethernet links and identifies errors in less than 10 seconds. The tester reveals network connectivity status and port information while ensuring documentation for every link. The comprehensive AutoTester measures PoE voltage, performs a switch test, and confirms the DHCP server is running and responsive. The tester also verifies gateway/router, internal IP service, and cloud reachability. When paired with the secure Link-Live Cloud Service, the Network Tester automatically uploads results and allows annotation of results enabling job supervisors to easily manage the progress of deployment and troubleshooting tasks assigned to their team.
-
Product
3671 Series Vector Network Analyzer (100kHz - max.43.5GHz)
3671
-
3671 series network analyzer provides frequency response, single-port, response isolation, enhanced response, full-dual port, electronic calibration etc. Offer various display formats, such as logarithmic amplitude, linear amplitude, phase, group delay, Smith chart and polar coordinates. 3671 series can accurately measure the amplitude frequency characteristics and phase frequency characteristics and group delay characteristics of microwave network.
-
Product
Absorber Lined Shielding Enclosure Measurements
ALSE
-
Due to on-going work in the standardization committee CISPR D (responsible for CISPR 25) the latest issue CISPR 25 Ed. 4.0 has not been cited to-date. In the meantime we are able to offer two different validation procedures:
-
Product
Dual 10th Order Lowpass Filter
64-VBF
-
The 64-VBF 10th order Lowpass Filter is a dual channel filter with independent switch settable Cutoff Frequency (Fc). The filter has a linear phase DC accurate root raised cosine response. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues. The output can drive a high speed DAQ multiplexer with its fast settle and capacitive drive capability.
-
Product
Power Transmitter
ITL-101
-
Power Transmitters measure precise power of any waveform generated by electronic circuits. The ITL-101 cannot only be used for stationary power measurements, but also for power control on machines using fast response option and bi-polar output option. For frequency inverter applications minimal use of energy is and issue and here the ITL-101 finds its place.
-
Product
Memory Analyzers
-
Market drivers in the memory sector have changed. Gone are the days of simply pushing Moore’s Law to ever faster data rates. The memory designs of today and tomorrow must also be smarter than ever before. Today, handheld and wearable computers must draw from a limited battery reserve while serving up fast, responsive, and compelling mobile experiences. Meanwhile the cloud of data centers and server farms that feed us these compelling experiences must continuously grow while simultaneously reducing overhead and environmental impact. These two different markets have the same goals: smarter memory, smarter control systems, and lower power usage.
-
Product
Mobile Communications DC Source, 15V, 3A
66311B
Battery Simulator
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66311B mobile communications DC source provides fast transient, exceptional sourcing, and precision measurement.
-
Product
Therm Penetration Probe
-
For applications where the center of the temperature sensing point will be approximately 0C(32°F). The temperature sensor is housed inside a stainless steel probe for fast response time.
