Circuit
-
Product
Four And Two-Port Multi-Protocol RS-232/422/485 M.2 Cards
M.2-COM-4SM Family
-
The M.2-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).
-
Product
Handheld Digital Multimeter, 4.5-digit, with Organic LED Display (OLED)
U1253B
Digital Multimeter
The Keysight U1253B 4.5-digit handheld digital multimeter (DMM) is feature-packed to simplify the troubleshooting of electronics and electrical circuits indoors, on the bench or in the field. Key capabilities include its organic LED (OLED) display that provides razor-sharp readings even in dark, off-angle situations. The U1253B is the world's first OLED handheld DMM of its kind. For those long, continuous measurements, the DMM equips you with the easy-to-use GUI data-logging software to automate virtually unlimited data recordings to PC. The U1253B comes with an integrated 20 MHz frequency counter for high frequency measurements, and a built-in programmable square-wave generator with selectable frequency and duty cycle. With the versatile U1253B, you are well equipped to perform thorough troubleshooting of any faulty circuit.A multi-award winner
-
Product
PXI BRIC8 FIBO Matrix Dual 80x4 3pin brkout
40-592A-104
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Circbord
8019-1
-
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges. 3U X 160mm Eurocard size will fit into 3U DIN Metric subrack.
-
Product
Hall Effect Sensor
-
The hall effect sensor products are manufactured according to international standards. Being an ISO 9001:2008, ISO 14001 and OHSAS 18001 certified company, DER EE is capable of designing and producing superior products to the highest standards of customers' requirements. Hall effect sensors we provided are a device containing both the sensor which produces a very low signal level and contains the vacuum tube amplifier and a high gain integrated circuit (IC) amplifier in a single package. hall effect sensor offer many applications to sense position and motion, to control electric motor control, to sense wheel rotation and so on.
-
Product
Full test development environment
XJDeveloper
-
XJDeveloper is a graphical application that allows you to quickly and easily set up and run tests on your circuit. With XJDeveloper you can reduce your time to market by reusing your test scripts all the way through the product design process and then in manufacturing.
-
Product
Elite™ 13.56 MHz RF Plasma Generators
-
The elite™ Series of RF plasma generators provides state-of-the art technology in a compact air-cooled package. The elite is designed with high speed closed loop control, a class E RF deck and a switching modulator for superior output performance. The elite design utilizes a single printed circuit board assembly for the full rack product virtually eliminating all internal wires and connectors and thereby providing the highest reliability available.
-
Product
EHV Circuit Breaker Analyzer
DigiTMR S2
-
The Vanguard DIGITMR S2 is an inexpensive, easy to use digital circuit breaker analyzer. The DIGITMR S2 can be operated stand-alone or can be computer-controlled. It can fully analyze a circuit-breaker’s performance by testing the contact time, stroke, velocity, over-travel, and contact wipe. Contact and motion analysis can be performed for all breaker contact operations (Open, Close, Open – Close, Close – Open, and Open – Close – Open). Timing results are recorded and displayed on the 240 x 128 pixels back-lit LCD screen and can also be printed on the built-in 4.5″ wide thermal printer.
-
Product
- RS-422 and RS-485 Lightning/Surge Protector
Model 22NX
-
FEATURES: Triple Stage Protection; Fast Response Time For RS-422 / RS-485; Prevents Damage to Modems, Converters, and Terminals; Accommodates Data Rates to 10 MBPS; Supports 4 Circuits. The Model 22NX Lightning Sponge is designed to accommodate high-voltage transients, slow them down and redirect them to a low impedance path to earth ground.
-
Product
AC-DC POWER SUPPLIES
-
Universal Input 85-264 VACContinuous Short Circuit ProtectionPCB MountableEfficiency to 82%Industry Standard Pin OutMeets, UL, CSA, TUV CE
-
Product
Rotating Cam Limit Switch
-
AMETEK Sensors, Test & Calibration
Today we have the most complete line of components and accessories for precise circuit control; no one else comes close. We design, engineer and provide technical support with on-site staff. With in-plant stamping, machining, welding, painting and assembly, we have control over our parts and processes.
-
Product
Clamshell Type Mechanical Fixtures
Series 10
-
Semco MT Series 10: An affordable solution for testing of printed circuit boards.
-
Product
6 Round Pin Trailer Circuit Tester
PT7897
-
Tests trailer circuits on most light/medium duty trucks and campers.Traces each lighting function to the terminal in question.
-
Product
Resistance Measurement
PROMET
-
High-precision micro-ohm measuring systems with adjustable DC test current for determining resistances on circuit breakers or inductive loads such as transformers, for example. The high-precision ohm meters of the PROMET series are used to determine very low electrical resistances in the µΩ range. The adjustable test current of up to 600 A in combination with a four-wire measuring method delivers measurement results which meet stringent accuracy requirements. State-of-the-art power electronics coupled with a robust design guarantee excellent reliability for use as a portable device in switching stations and industrial environments. Typical applications include determining the contact resistance of switchgear devices and determining the resistance on inductive loads such as transformers.
-
Product
BGA Sockets
-
Ironwood has the most comprehensive collection of BGA (Ball Grid Array) sockets that can be used for prototype application, silicon validation, system development, thermal characterization, burn-in application, functional production test, etc. BGA socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. BGA sockets for prototype applications, silicon validations, system development applications uses low cost elastomer contact technology.
-
Product
Charge System Safety
-
Renesas' charging system safety circuits are optimized to provide a redundant safety protection to an Li-ion battery charging system by monitoring input voltage, battery voltage and charge current.
-
Product
PXI RTD Simulator Module, 4 Channel, PT500
40-263-502
Simulator
The 40-263-502 is a 4-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
High Impedance Active Probes
7
-
Designed as a companion probe to Models 12C and 18C for driving integrated circuit lines so the Model 12C and 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes and can also be bent to any shape in order to accommodate a variety of probing geometries.
-
Product
EV Battery Pack Test Equipments
-
Guangdong Bell Experiment Equipment Co.,Ltd
All industrial battery tester from BELL lithium battery test chamber supplier meet the standards of GB31467.3, ECE-R100 and UL2580. The tests mainly simulating all the condition that driving an EV meet, including battery crush test, battery drop test, flammable test, temperature cycle test, short circuit test, thermal test, explosion test, and environmental test, etc.
-
Product
High AC Current Capacitor
LC1/LC2/LC3-RNM
-
Induction Heating Processing Equipment, Electric Current Welding, High Power Resonant Circuits, Motor Controls; Oscillating, Bypass, Coupling circuits, High AC Current applications, High-Frequency AC Filter and Medium Frequency Power applications.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
-
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Power Monitor, AC- or DC-Powered
109
Power Monitor
NAI’s 109 is an AC- or DC-Powered Power Monitor used to monitor voltage, frequency, and phase characteristics of single- or three- phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.The 109 monitor provides three separate control circuits and output relays indicating the condition of each line characteristic. It is ideally suited for rugged defense and industrial applications.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-03
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Transient Over-voltages Tester
SUG335
-
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
Product
Sensor Circuit Probe
-
The probe can be used in 12/24 volt system with ECM/ECU either independently or used together with a diagnostic scanner to distinguish faults that lie in the sensor itself or the connection wires. The simulated voltage is used to emulate signals generated by different types of sensors.
-
Product
Switch Mainframe
SW1001
-
Switch between voltmeter and battery tester while testing. 66 channels max. (2-wire) to 18 channels max. (4-terminal pair). Circuit design friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*). For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz. For OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Measure battery modules up to 60 V DC.
-
Product
Limit Controllers
-
Limit Controllers shut down power to heating and cooling circuits in the event of an out-of-range hot or cold condition. Disables a redundant coolant valve to protect against primary coolant valve failure. Easily read and set by the user. The large LED display indicates temperature and system status.
-
Product
Digital Tachometer - Non Contact / Contact / Non Contact & Contact
MODEL - KM- 2234BL / KM 2235 B / KM 2241
-
Kusam Electrical Industries Limited
Digital Tachometer uses latest technology for accurate measurements. It has Exclusive one chip of Microcomputer LSI Circuit, It is housed in tough ABS case & has ergonomic design for easy holding in the hand.
-
Product
IGBT For IH
-
IGBT devices for induction heating (IH) (soft switching), recommended for 10 to 100 kHz frequencies, and not guaranteed against short circuit.
-
Product
Silicon Detectors
-
Through the photovoltaic effect, detectors provide a means of transforming light energy to an electrical current. The root of the theory behind this phenomenon is a small energy gap between the valence and conduction bands of the detector. When light, with enough energy to excite an electron from the valence to the conduction band, is incident upon the detector, the resulting accumulation of charge leads to a flow of current in an external circuit. Since light is not the only source of energy that can excite an electron, detectors will have some amount of current that is not representative of incident light. For example, fluctuations in thermal energy can easily be mistaken for light intensity changes. A variety of these "non-light" contributions are present and, when summed up, make up the total noise within the detector.
