Circuit
-
Product
Thermal camera
-
An efficient way to prevent faults in circuits or facilities by locating hot spots, as well as in veterinary medicine or location of living beings.
-
Product
LXI Low Thermal EMF Matrix 1-pole 56x33
60-510-001
Matrix Switch Module
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
Product
Precision Condenser Microphone
2575
-
Performance:Nominal Microphone Diameter1"1" Frequency Response: Characteristic (at 0 incidence) Random IncidenceRandom Incidence Open Circuit Sensitivity: 45 mV/Pa Resonant Frequency (90 Phase Shift)8000 Hz8000 Hz[1] Inherent Noise<10 dB(A) re 20 Pa<10 dBTemperature Range (Operating)TBD FTBD C Humidity Coefficient of Sensitivity (0 to 95%, non-condensing)0.001 dB/%RH
-
Product
SMD Test Probes
-
The Parrot Clip, model PCM W1 or PCS-MB W1 invention can be connected to resistance’s, diodes, integrated circuits (SOIC, SO) etcThe advantage of the Parrot Clip is given by the double metal connection made between the new metal tip and the steel hooked rod, spring loaded. This connection, being made by metal parts is electrical and mechanical reliable, even if the contact point are small. Connections are resistant even at high temperatures.
-
Product
I²C/SPI Interface Device
Interface
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
-
Product
Control Board For Testing PCBs
TCC 1800
-
The TCC1800 Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via a galvanically separated USB interface. The TCC1800 is designed to work with positive voltages up to 24V. All inputs and outputs are protected against higher voltages however. The card provides basic IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, Serial (UART) and I2C interfacing.
-
Product
AC and DC Electronic load
63800 series
-
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing thereby giving reliable and unbiased test results. The 63800's state of the art design uses DSP technology to simulate non-linear rectified loads with its unique RLC operation mode. This mode improves stability by detecting the impedance of the UUT and dynamically adjusting the load's control bandwidth to ensure system stability. Comprehensive measurements allow users to monitor the output performance of the UUT. Additionally, voltage & current signals can be routed to an oscilloscope through analog outputs. The instrument's GPIB/RS232 interface options provide remote control & monitor for system integration. Built-in digital outputs may also be used to control external relays for short circuit (crowbar) testing.
-
Product
Power Bus
MS 1606
-
The PowerBus is used to service printed circuit boards, instruments and systems, which has Micro controller / Microprocessor. The PowerBus has RS232 Communication for PC interface. The PowerBus connects to the UUT through the microprocessor / micro controller socket. The UUTs microprocessor / micro controller is removed from the UUT and it is replaced by the PowerBus. The Power Bus adapts microprocessor specific function as pin layouts, status / control function, interrupt handling, timing and memory and I / O addressability.
-
Product
Surface-Mount Noise Sources
-
Mercury’s family of surface-mount noise sources provides exceptional performance in a compact and easy to integrate package. These products are ideal for applications such built-in test and dithering circuits where the system requirements drive a need for compact, surface mount technology.
-
Product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TV
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used for measurement of DCcurrent etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Pt RTD Temperature Monitor
SIM923
-
Stanford Research Systems, Inc.
The four channels in the SIM923 have independent, stable 1 mA current sources to provide sensor excitation. Sensor resistance is determined ratiometrically with a half-bridge circuit consisting of the sensor and an internal reference resistor.
-
Product
AC Current Digital Clamp Meters
-
Precision Mastech Enterprises Co.
Handheld, safe, and non-contact electrical tools designed to measure alternating current (AC) without disrupting the circuit
-
-
Product
Wave Soldering Machines
-
Shenzhen Leadsmt Technology Co.,Ltd
A bulk soldering process used for the manufacturing of printed circuit boards.
-
Product
VME Test Extender 3U/220mm J2
111EXT3122-12XX
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783124-01
Signal Module
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
Octocouplers
-
Panasonic Industrial Devices Sales Company of America
Panasonic's PhotoIC Coupler is a high performance optocoupler which consists of LED in input circuit, and custom IC in output circuits. PhotoIC Couplers are commonly used for high speed communication requiring physical isolation in various equipment and devices.
-
Product
PXI Breadboard Module, 1-Slot, 96-Pin Micro-D
40-220A-001
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
Fuse Buddy Current Loop
307M/308B
-
*Just clamp your current probe over the loop to access the amperage draw through a fused circuit. *Easy testing access, plugs right into fuse socket, no more hand made adapters. *Testing range 0-30 Amps - Do Not Exceed 30 Amps
-
Product
Auguscope Portable Diagnostics
-
The Auguscope incorporates over 3 years of Electronics and Analog circuit development, resulting in best in class analog signal sampling at never before seen sampling rates. The Auguscope can record both Vibration and Ultrasonic (AE) sensors and can be used for mechanical diagnostics, as well as leak detection, pump cavitation and steam traps. The result is a small, portable device, that replaces over $40,000 worth of monitoring equipment.
-
Product
Standalone Test System
1000 Series ATE
-
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
Product
Test Equipment
Flexible Coil Current Sensor
-
*Analysis of harmonics, power measurements*Very high-current monitoring*Measuring starting transients of electric motors*Sudden short circuit testing*Arc furnace currents*High-current monitoring of switch-gear and fuses*Data logging*Can be measured by popular multi-meter
-
Product
10 MHz AGC Distribution Amplifier
FS710
-
Stanford Research Systems, Inc.
For installations which require many 10 MHz outputs at a remote location from the source, the FS710 AGC Distribution Amplifier offers seven independent outputs from one input. With an AGC circuit capable of adding up to 30 dB of gain, this amplifier can be used to provide a 10 MHz reference at locations as far as a mile from the source.
-
Product
SIMRC - SMB RF Adapter PCB
1092-001
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Active Probe, 5 Hz to 500 MHz
41800A
General Purpose Probe
The Keysight 41800A Active Probe provides high input impedance from 5 Hz to 500 MHz. The Keysight 41800A is a valuable tool when used with a network and spectrum analyzer for circuit signal analysis.
-
Product
Complete Graphical Power Quality Analysis System
PK5064-PRO
-
The PK5064-PRO is a recommended choice for comprehensive power quality studies, energy audits, load studies, harmonic analysis, and more. Wide-range flexible current probes allow you to get into tight and confined spaces, wrap around large conductors, and measure almost any AC circuit that comes your way.
-
Product
Miniature Circuit Breakers
-
Miniature circuit breakers are applied to protect electric applications against an over current. When an electrical circuit is not protected the application can be damaged and unsafe situations may happen like fire. Mors Smitt delivers a wide range of miniature circuit breakers specially designed and tested according to railway regulations.
-
Product
OverHead Lines Contact Voltage & Low Voltage Indicator
LVD-415
-
Standard Electric Works Co., Ltd
● No batteries required.● Every circuit is doubled.● Buzzer indicates voltage detected.● Led indicates voltage detected.● Neon scale indicates voltage.● Dual HBC fuses.● High grade fiber glass probes.● Super polished fiber glass.● High strength connecting cord.● Heavy duty rated.● Replaceable tips.● Choice of tips available.● Lightweight.● Small storage space.● Strong strength reliefs.● Double poles non-polarized.● Suitable for 45 to 70 Hz networks.● Contact detector type.● Passive circuitry.● Fiber glass 1.6mm - CU 35um PCB.● Super bright neon lights and LEDs.● Ergonomically-designed.● EN 61010-031 CAT IV 500V.
-
Product
Electric Vehicle Battery Cell Tester
MCV
-
The MCV is a low-current life cycle test system for development of primary and rechargeable batteries in various chemistries. Operating from a common microprocessor, multiple circuits in the MCV module can run individual test programs. Additionally, the MCV is designed and built for ease of maintenance and service. The modular construction means that most subassemblies, large or small, remove easily for service outside the cabinet and fast replacement.
