Asynchronous Transfer Mode
Testing Asynchronous Transfer Mode (ATM) communications and network equipment includes three primary testing phases: conformance verification; interoperability testing; performance benchmarking
-
Product
4 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTF
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
-
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
Product
Polarisation Mode Dispersion
PMD500
-
PMD500 is our polarisation mode dispersion (PMD) measurement system available in two PMD measurement methods, designed to produce accurate measurements quickly and with confidence.
-
Product
Cable Tester, HDMI Cable, Digital, LAN Tracer, Talk Mode, Tone Generator
TCT-320
-
Designed to check and troubleshoot pin connections of HDMI cables. Tests the continuity of each pin of HDMI cable prior to installation to save time on install.
-
Product
IEEE488 (GPIC, HPIB) PCI Interface Card - Fits 3.3V or 5.0V Slots, 1KByte Transfer FIFO
GPIB-PCI-XL
-
The GPIB-PCI-XL is a PCI GPIB controller card that converts any PC with a PCI bus slot into a GPIB controller.
-
Product
Matrix Fiber Optical Switch at Single Mode Type A 1550nm with LC/PC Connector
GLSUN-MEMS-8x8
-
Guilin GLsun Science and Tech Group Co., LTD
Fiber Configurations 8x8 ports Fiber Type SM, 9/125 umTest Wavelength 1530/1570 nm Operating Voltage 4.8~5.5VSwitch Type Non-latching Fiber Length 0.5m±5cmConnector LC/PC Tube Type 900 umOperating Temperature -10°C~ +70°C Storge Temperature -40°C ~ +85°C
-
Product
Compact Tunable Laser Source with Continuous Sweep Mode, 1520nm to 1630nm
81940A
Laser Source
Keysight's 81940A high power compact tunable lasers enables optical device characterization at high power levels and measurement of nonlinear effects. It's improves the testing of all types of optical amplifiers and other active components as well as broadband passive optical components. As single slot plug-in modules for Keysight's 8163A/B, 8164A/B and 8166A/B mainframes, they are a flexible and cost effective stimulus for single channel and DWDM test applications. Each module covers a total wavelength range of 110 nm in the C+L-band.
-
Product
PXI/PXIe Microwave Transfer Switch, Single, 50GHz, 50Ω, SMA-2.4
40-782B-551
Switch Module
The 40-782B-551 (PXI) and 42-782B-551 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 50GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
-
Product
PXI/PXIe Microwave Transfer Switch, Single, 18 GHz, 50 Ω, SMA, Failsafe, Remote Mount
40-782B-521-E
Switch Module
The 40-782B-521-E (PXI) and 42-782B-521-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 18 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
PXI Dual Transfer Switch 18GHz 50Ω SMA
40-782-522
Switch Module
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
Product
LXI 16:1 Optical MUX FC/APC Single Mode
60-850-013
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI/PXIe Microwave Transfer Switch, Dual, 50 GHz, 50 Ω, SMA-2.4, Failsafe, Remote Mount
42-782B-552-E
Switch Module
The 40-782B-552-E (PXI) and 42-782B-552-E (PXIe) dual failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 50 GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
-
Product
Coaxial Transfer Switch, DC to 26.5 GHz
87222C
-
Flexibility is essential in signal routing applications, and the Keysight 87222C 4-port coaxial transfer switch offers just that. It provides exceptional repeatability, low insertion loss, and high isolation. These switches provide simplification of design in signal routing and conditioning applications. The Keysight 87222C can be used in a variety of applications such as, a drop-out switch, switching two inputs and two outputs, or signal reversal switching.
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) SC M50
40-860-222-M50
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode) SC M50
40-860-212-M50
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Logic Analyzer Module With State Mode Up To 4Gb/s
U4164A
-
The U4164A logic analyzer provides industry’s highest data rate state mode (up to 4 Gb/s), highest deep trace timing mode (up to 10 GHz), and deepest memory (up to 400 Mb), enabling validation and debug of DDR4 or LPDDR4 at data rates over 3.5 Gb/s.
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode)SCM62.5
40-860-212-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber.
-
Product
LXI 16:1 Optical MUX SC Multi Mode
60-851-213
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI Microwave Transfer Switch, Single, 26.5 GHz, 50 Ω, SMA, Failsafe, Remote Mount
40-782B-531-E
Switch Module
The 40-782B-531-E (PXI) and 42-782B-531-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 26.5 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) SC M62.5
40-860-222-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
LXI Dual 8:1 Optical MUX LC Single Mode
60-850-412
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI Dual Transfer Switch 40GHz 50Ω SMA-2.9
40-782-542
Switch Module
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
Product
Satellite Based File Transfer
SatDrive™
-
Copy files from one computer to another via satellite. Rugged and easy to use. The SatDrive is a great solution for sending files from remote locations.
-
Product
Single Wafer Transfer Tools
-
Dou Yee Enterprises (S) Pte Ltd
Dou Yee Enterprises Single Wafer Transfer Tools
-
Product
Solid State PIN Diode Transfer Switch, 100 MHz to 18 GHz
P9400C
-
The Keysight P9400C solid state PIN diode transfer switch offers outstanding performance in terms of port-to-port isolation, switching speed and low insertion loss over a broad operating frequency range of 100 MHz to 18 GHz. The P9400C is particularly well suited for ultra-fast RF and microwave switching applications in instrumentation, communications, radar, switch matrices and various other test systems where high isolation, speed and lifetime of a switch is critical.
-
Product
PXIe Microwave Transfer Switch, Single, 26.5 GHz, 50 Ω, SMA, Failsafe
42-782B-531
Switch Module
The 40-782B-531 (PXI) and 42-782B-531 (PXIe) single failsafe transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 26.5 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
Mode Locked Synthesizer
IT9200
-
The ITS-9200 is a synthesized RF source with a flexible locking capability that allows it to be phase-locked to non-standard external references. It is specifically designed for synchronization to mode-locked lasers with pulse output frequencies in the 72-80 MHz region, although it can be easily modified to adapt to other reference frequencies.
-
-
Product
Asynchronous Fast SRAM
-
For industrial and communication applications, 4 MB Asynchronous Fast SRAM is available.
-
Product
PXI/PXIe Microwave Transfer Switch, Single, 50 GHz, 50 Ω, SMA-2.4, Failsafe, Remote Mount
42-782B-551-E
Switch Module
The 40-782B-551-E (PXI) and 42-782B-551-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 50 GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
