Product

Intelligent and Unidirectional Scrape Tester

ZDG-25

-

Shanghai Dean Electrical Co., Ltd

ZDG-25 - Shanghai Dean Electrical Co., Ltd

Executive standard: GB/T4074.3-2008/IEC60851-3Inspection standard: JB/T4279.9-2008Meet GB/T6109-2008 standard requirementsUsed to test the film scrap resistance of enamelled round wires with nominal conductor diameter above0.250mm;Application of SCM control，enter the weight value, operation will be completed automatically: put down the scraping rod, stop while film scratch, calculate and show the scraping force, raise the scraping rod, return to zero, sample rotates 120°and repeat the same operation, calculate and show the scraping force of three times and average scraping force.When film is scratched, film scraper would automatically stop scraping, with exposed conductor of sample＜3mmWith the advantages of high sensitivity, good repeatability, stable and reliable characteristics.

Product

Closed-Loop Servohydraulic Test Bench Control System

-

ZETLAB Company

ZETLAB Company

Closed-loop servohydraulic test bench control system is based on digital devices of ZETSENSOR series with CAN interface. This system has fast response characteristics, high precision, and compact dimensions. The system enables comprehensive control of the servo drive in automated mode in compliance with the set test parameters such as pressure (force), displacement, along with the parallel control of other system parameters such as temperature, pressure, filter plugging, oil pressure, etc.

Product

"Stiff Grid" and Parallel Operation AC Generator Excitation Regulator

SVRFP

-

Kinetics Industries

SVRFP - Kinetics Industries

The Kinetics model SVRFP Exciter/Regulator rectifier is designed and rated in capacity and operating parameters for the application of exciting the fields on an AC generator in parallel with other AC generators and the power system is a "stiff system" in relation to loading. A "stiff system" is a generating system that is of sufficient capacity or the generator is "small" in relation to the system grid, that the AC system voltage under impulse/step loading condition does not require forcing of the generator field to maintain the power grid voltage. Systems are designed with a standard unit service factor to operate within the +10% to -20% nominal voltage rating at 100% current rating.

Product

Test Contactor/WLCSP Probe Head

ACE

-

Cohu, Inc.

ACE - Cohu, Inc.

ACE™ test sockets offer optimal RF performance for fine pitch FBGA, QFN and wafer-level packages for Power Amplifiers, RF switches and mobile communications. Supporting pitches down to 0.4 mm, ACE features an innovative design that provides superior performance, improved yields and power efficiency.ACE probe heads deliver exceptional electrical performance, both DC and RF. Manufactured from HyperCore™ base material, a proprietary material of Cohu’s Everett Charles Technologies, ACE probes have the electrical properties of BeCu with the non-oxidizing properties of a precious metal. The short signal path, sharp tips, and large contact area between plungers provide high current conductance and reliable contact with less force.

Product

Computer Controlled Electro-hydraulic Servo Bending Testing Machine

SBT Series

-

Jinan Testing Equipment IE Corporation

SBT Series - Jinan Testing Equipment IE Corporation

SBT series computerized bending testing machines are mainly used for bending and pressing tests for metallic sheet & round bars as per standards of GB/T232-2010 & ISO 7438-2005 Metallic Materials-Bend Test. An axial oil cylinder for bending test is installed on the top cross-head. Two pressing oil cylinders are installed at both sides of the frame, which adopts the synchronous control, to realize the pushing and pressing force on the bending support to adjust the distance between pivots. The pressure meter indicates the pressure in bending or pressing. Various load display can be selected, such as display through the pressure meter, digital display, and computer screen display etc. The computer control type SBT bending testing machine can do the bending test automatically or manually. TThe applies bending force can be adjusted or controlling the oil feed valve.

Product

Automated Switch Test Equipment

-

TRICOR Systems Inc.

TRICOR Systems Inc.

TRICOR Systems Inc. offers test equipment for switches, keypads, rubber, etc. Virtually any component where accurate force-displacement and measurements are required. From our Model 933A, a low cost life test system to our Model 925 test station used to obtain precise force measurements relative to displacement; we have the system you require.

Product

Testing Tensile Strength of Overlays, and Overlayments

James Bond Test ™ MK III

-

James Instruments Inc.

James Bond Test ™ MK III - James Instruments Inc.

The James Pull Off Adhesion/Bond Tester measures the pull force used to pull a 2? or 3? disc away from the material being tested. This pressure is displayed on a precision gauge and can be related directly to the strength of the adhesion to the surface being tested.

Product

Digital Strain Gauge Sensor

ZET 7111

-

ZETLAB Company

ZET 7111 - ZETLAB Company

The ZET 7111 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or separate external tension gauges connected using half-bridge or bridge scheme.

Product

Force Sensors In S-form For Pull/push Direction

-

INELTA Sensorsysteme GmbH & Co. KG

INELTA Sensorsysteme GmbH & Co. KG

With very small space requirement and high breaking force made from tempered stainless steel, suitable for measuring medium to high forces. Easy integration and mounting by threaded bores.

Product

Dual Loop Master Controller

-

Xcite Systems Corporation

Xcite Systems Corporation

The Xcite System Master Controller provides all dual loop functions needed for accurate closed loop control and display of the static and dynamic test variables, while producing the highest electro-hydraulic frequency response. At the heart of each Xcite System is the Master Controller, a compact electronic control package which provides all of the controls and displays necessary to operate a controlled force or torque exciter system. The Xcite Master Controller is unique in that it provides electro-hydraulic excitation over a broad frequency range, unprecedented by any previous electro-hydraulic excitation system. It achieves its great frequency range through the use of sophisticated circuitry, high voltage inputs to the servovalve and compression control of the dynamic feedback variable in addition to the conventional servo control of the static loop. Static parameters such as force or displacement may be matched with dynamic control variables such as force, displacement, velocity, acceleration or strain for maximum test flexibility.

Product

Load Cells

-

PENKO Engineering B.V.

PENKO Engineering B.V.

A load cell is a sensor which transforms the load or force applied to it into an electrical signal. Load cell sensors are based on the strain-gauge principle i.e. a sensor whose resistance varies with applied force. They are the most widely used as load transducers in all areas of weight measurement from retail scales, the process industry and medical applications.

Product

Force and Material Testing

-

The L. S. Starrett Company

The L. S. Starrett Company

Starrett Force and Material test solutions range from simple hand-held measurements to highly advanced applications with extreme accuracy.

Product

Sensors

2D Fiber Probe

-

Werth Inc.

2D Fiber Probe - Werth Inc.

Smallest and most accurate probe for 2D evaluations world-wideMechanical fiber sensor with optical evaluation from image processorTransmitted light and self illumination modeLowest contact force of 1 µNSphere diameters down to 25 µmControl and evaluation software for fully automatic measurements

Product

Piezoelectric Sensor Group

-

Fuji Ceramics Corporation

Fuji Ceramics Corporation

This section introduces piezoelectric sensor products best suited for measuring, testing, and diagnostic equipment, such as accelerometer, acoustic emission (AE), and force sensors.

Product

Surface Analysis

Innova-IRIS

-

Bruker Optics

Innova-IRIS - Bruker Optics

This provides researchers a perfect combination of chemical or crystallographic information at high spatial and spectral resolution with the most advanced atomic force microscopy characterization. The Innova-IRIS can be integrated with your choice of a leading Raman system to provide the best opaque sample TERS investigations available today. However you tailor your system, your application will benefit from Bruker exclusive, high-contrast IRIS TERS probes and the best tip preservation and lowest drift, guaranteeing that alignment is preserved even over the optical integration times necessary to interrogate weak Raman scatterers.

Product

Naval Navigation

-

exail

exail

In today’s high-risk operational environments, having a clear, accurate view of the maritime domain is critical. With proprietary technologies for GNSS-independent navigation, secure data management, and real-time insights, Exail offers a unique, integrated navigation solution for comprehensive situational awareness, both on the surface and underwater. This approach gives naval forces the resilience, safety, and operational edge needed to navigate dynamic conditions and enhance mission effectiveness.

Product

Piezo-Electric Measurement Trainer Module

-

Unitech Scales And Measurements Pvt. Ltd

Unitech Scales And Measurements Pvt. Ltd

PiezoElectric Trainer comprises of piezoelectric crystal mounted inside housing and fitted on a base plate. Digital indicator is supplied to indicate the vibrational force.

Product

VisualIMPACT Software

-

Instron

Instron

CEAST VisualIMPACT software is designed to control CEAST Pendulums and Drop Tower Series, manage tests and offer a user-friendly interface when using the Data Acquisition System. It records force and absorbed energy data related to impacts, visualizes and helps analyze the results and calculates resilience. The operator is guided through parameters setup by means of tables describing strikers and specimens that are filtered according to the test type and international standard selected. In the case of instrumented tests, many possibilities for data analysis and visualization are made available. The results are shown through comprehensive and customizable graphs and can be filtered by break type (only specimens with a selected break type are shown). Working with groups of test, the software performs a statistical analysis, and the operator can pick and discard single test results. Different measurement units can be selected. It is possible to print reports and to export data totally or partially. Recent improvements include the possibility to set a number of user profiles, including graphic settings, default printing options, advanced parameters for data analysis and so on, switching quickly from one another when looking at results. The introduction of a new Data Acquisition System (CEAST DAS 64K) in the Impact product line has also triggered a number of new capabilities for the SW, which is now able to process a more comprehensive calibration file for instrumented tups and hammers and manage DAS configurations with a wider range of data acquisition channels.

Product

TSO'd Airspeed

-

UMA, Inc.

UMA, Inc.

Airspeed Indicator is intended for use on an aircraft to indicate the speed relative to the air at sea level and at any other altitude, to indicate the equivalent speed corresponding to the actual force of the air.

Product

Acceleration Testing

-

Aero Nav Laboratories, Inc.

Aero Nav Laboratories, Inc.

The acceleration test is performed on a centrifuge to assure that material can structurally withstand the steady state inertia loads that are induced by platform acceleration, deceleration, and maneuver in the service environment, and can function without degradation during and following exposure to these forces. Acceleration tests are also used to assure that material does not become hazardous after exposure to crash loads. The acceleration test method is applicable to material that is installed in mobile platforms such as aircraft, helicopters, aerospace vehicles, air-carried stores, ground-launched missiles, trains, ships, automotive vehicles, etc.