Light Fixture
-
Product
Light Meters
-
TES Electrical Electronic Corp.
Dual Display, 4 digit LCD reading.Spectral Sensitivity close to CIE phototropic curve.Measuring levels ranging 0.001 to 1999kAccurate and instant response. Luminance ratio A/B
-
-
Product
Lighting Systems for Aviation
-
Flying on every major platform, Astronics offers decades of proven experience in delivering standard and custom lighting solutions that illuminate the world’s aircraft. From commercial to business to military, chances are we offer experience with your type of fixed-wing or rotorcraft program.
-
Product
Light 0.75 (21.00) - 2.00 (57.00) Bead Probe
BTP-25C-2
-
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Test Fixture
OCP NIC 3.0
-
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
Product
Light 0.48 (14.00) - 2.00 (57.00) High Performance Bias Ball Probe
POGO-62T1-2
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Test Fixtures
-
At A.T.E Solutions we have a dealt with a wide range of test subjects in the past 30 years and have extensive experience in providing reliable test fixture solutions.
-
Product
Mode-Conditioned Light Sources
-
Thorlabs' Mode-Conditioned Light Sources are fiber-coupled LED sources that have an output with a flat-top profile in the far field. Common applications include the testing of multimode fused fiber components as well as verification of modal behavior in fiber-based setups. Standard fiber-coupled LED sources can have a range of output profiles that are usually not uniform and vary from source to source. This can be dependent on emitter orientation, alignment with fiber tip, and connector assembly. These mode-conditioned sources have been engineered to distribute light evenly into all transverse modes, resulting in an equilibrium modal distribution at the output. The front panel includes an adjustment knob to control the power and an output port that accepts 2.2 mm wide-key FC/PC connectors. A DS15 15 V power supply with a location-specific plug is included with each device.
-
Product
Light 0.75 (21.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-25Z1-2
-
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Light Sensors
-
ams provides the industry’s broadest portfolio of high-performance and high-sensitivity digital discrete and integrated module optical sensors.
-
Product
Light Curtains
-
Leuze electronic GmbH + Co. KG
Switching light curtains are perfect for monitoring large measurement fields. They react as soon as anything or anyone penetrates this field. Their fast configuration and simple handling save time and money compared to imaging processes. Thanks to different beam spacings and measurement field lengths, switching light curtains can be used to solve a range of application problems.
-
Product
Light 0.83 (24.00) - 2.00 (57.00) Bead Probe
BTP-1HF-2
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
GPS/FMS Universal Test Fixture
TA-3000
-
This panel was designed to give the avionics shop the capability to test and troubleshoot many of the GPS, GPS/COMM and FMS units on the market today. Breakout jacks are provided for both analog and digital signals that need to be monitored or simulated. A data port update jack is provided as well as Arinc 429 and RS232 loopback switches. Switches for Gillham altitude are provided as well as fuel flow adjustments. An array of annunciators and configuration switches are also provided to verify those outputs and inputs. Optional UUT configuration overlays also availabl
-
Product
Ambient Light Sensors
-
Renesas' ambient light sensors can adjust a display’s backlight, which improves user experience and power savings by optimizing the display’s viewability. Their ultra-low light sensitivity, low power consumption, ideal spectral response, and easy to use simple output algorithm make them best-in-class. We offer a full suite of light-to-analog and light-to-digital solutions to suit your applications requirements and budget.
-
Product
Towing Dynos for Full-Sized Cars & Light Trucks
-
Designed to maintain 2,248 to 5,620 lb (10,000 to 25,000 N) of constant drawbar pull, our towing dynamometers for full-sized cars to light trucks are powered by an industrial generator to provide unlimited testing at low speeds. Each model features aluminum frame, independent suspension, aero dynamic body and wireless touchscreen controller.
-
Product
Dynamic Light Scattering (DLS)
NANOTRAC
-
Dynamic Light Scattering (DLS) is an established and precise measurement technique for the characterization of particle sizes in suspensions and emulsions. Microtrac is a pioneer of particle analysis technology and has been developing optical systems based on Dynamic Light Scattering for over 30 years.
-
Product
Light Sources
-
There are many low cost artificial light sources used for illumination or for industrial applications: tungsten or halogen bulbs, fluorescent lamps, LED lamps etc. Some of these sources have regulated intensity of emitted light. However, there very few calibrated light sources of precisely known parameters. A light source can be considered as calibrated when its user can precisely regulate its photometric/radiometric parameters like luminance (or illuminance), radiance (or irradiance) at defined spectrum of interest. Such light sources are needed in many applications among them, in systems for testing night vision devices, VIS-NIR cameras and SWIR imagers. Inframet offers a series of calibrated light sources that can be divides into three groups:
-
Product
Light 0.60 (17.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-72T38-2
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,700Overall Length (mm): 43.18
-
Product
Light 0.60 (17.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-72U-2
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,700Overall Length (mm): 43.18
-
Product
Functional Test Fixtures
-
Businesses rely on Circuit Check’s functional test fixture expertise. Functional test typically applies full operational power to a loaded printed circuit board in order to determine if the PCBA performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies.
-
Product
28 cm2 Test Fixture Operations Kit
-
The 28 cm2 Cell Test Manifold Kit offers a highly effective solution for testing of individual planar solid oxide fuel cells. The kit contains all items necessary to easily mount cells with ~100 cm2 substrates. Designed for both long and short term experiments to measure properties such as fuel utilization, thermal gradients, red-ox cycling and longevity/degradation, these kits will accelerate your research and development activities.
-
-
Product
USB A TX Test Fixture
AUT20135
-
This newly designed AUT20135 brings enhanced user-experience with the following features:
-
Product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-1Z-2
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
-
Product
Evaporative Light Scattering Detector
ELSD-LTII
-
The ELSD-LTII utilizes a high-efficiency LED and enhanced digital signal treatment to minimize noise and deliver optimum sensitivity for trace analysis. An innovative cell design also reduces band broadening and allows sensitivity levels below 200 picograms. The high-performance optical detection system can also be used for combinatorial chemistry and high-throughput screening applications. The new Low Temperature Evaporative Light Scattering Detector (ELSD-LTII) is an easy-to-operate, universal detector that identifies analytes with uniform sensitivity regardless of their spectroscopic properties. It is not a spectroscopic detector. Instead, it removes the mobile phase through evaporation and then makes a light scattering measurement of the dried analyte particles.
-
Product
Underwater LED Lights, 120Vac, 4,200 or 7,300 Lumen Output
LED-R-Series
-
The Teledyne Bowtech LED-R-Series underwater LED lights are 120Vac and available with 4,200 or 7,300 lumen output. These lights feature our latest LED technology and are now a real alternative to AC incandescent lamps.Due to Teledyne Bowtech's continued history of innovation, these lights feature the latest and best underwater LED lighting technology available.
-
Product
Pre-configured Power Device Analyzer / Curve Tracer (B1505A with modules and fixture)
B1505AP
-
B1505AP provides eight different pre-configured packages that satisfy a wide variety of power device measurement requirements. The package can be selected according to voltage / current range and the requirement for capacitance measurement.
-
Product
Fiber Optic Light Source
-
Fiber optic light source is a fiber optic test equipment to measure the fiber optic loss for both single mode fiber cable and multimode fiber cables; usually the fiber optic light source is used with the fiber optic power meters. This fiber optical light source can provide wavelength output according to the specific requirements including the 650nm red source, 1310nm/1550nm wavelength for the single mode fiber and 850nm/1300nm wavelength for the multimode fiber. Used together with our fiber optic power meter, they act as an economic and efficient solution for the fiber optic network works.
-
Product
3.4 MP Custom Lens Low Light Camera Module
e-CAM30_CUMI0330_MOD
-
e-CAM30_CUMI0330_MOD is a high performance, small form factor, 3.4 MP pluggable Low Light Camera Module with S-Mount lens holder. It is based on AR0330 - a 3.4MP CMOS Image sensor from ON Semiconductor®. It has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs the entire Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images, videos and the optional MJPEG compressions.
