Tunable Laser Sources
See Also: Tunable Lasers, Laser Sources
-
product
SNS Series Noise Source 10 MHz to 18 GHz (ENR 15 dB)
N4001A
The SNS series N4001A noise source is ideal for general purpose use with a low reflection coefficent and a nominal ENR of 15 dB from 10 MHz to 18 GHz.
-
product
Dynamite Source Controller
BOOM BOX III
*Easy to Use, just hold the Arm and Charge toggles, Unit charges and is ready to fire*Web based interface allows easy setup and storage of data on PC, Tablet, or Cell phone*Shooter updated with easy to read graphical display and status LEDs*Same unit used for Encoder and Decoder modes
-
product
Noise Source, 10 MHz to 18 GHz, nominal ENR 6 dB
346A
The Keysight 346A noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The very small change in reflection coefficient (<0.01) from ON to OFF is designed especially for accurate characterization of input-impedance-sensitive devices (like GaAsFETs and many UHF amplifiers).
-
product
Incandescent Light Sources
Collimated, uniform, 1 inch diameter output beamSupports 75W-300W QTH LampsSupports xenon, mercury, & mercury-xenon arc lampsForced Air CooledRefractive condensing optics attachments availableVariable power supply (purchased separately) with optical feedback (option)Vertically mounted arc lampSide exit port with back spherical reflector
-
product
Large Area UV Light Source
Model 30L
The OAI UV Light Source Grande is a large area collimated light source. The device is available with output power up to 10KW. Utilizing collimating mirrors, the UV Light Source Grande is a highly efficient UV light source intended for a variety of larger-scale applications.
-
product
In-Situ Cross- Stack Laser Analyzer
LS25 is an in-situ analyzer for non-contact measurement of the concentration of gases. The measuring principle of the LS25 is based on the principle of single line spectroscopy (Tunable diode laser absorption spectroscopy, TDLAS). A single cross-sensitivity-free absorption line of the gas to be measured is selected in the near infrared range. A single-mode diode laser operating at room temperature scans the respective absorption line. By using an opposite receiver, the absorption caused by the sample gas is measured and from this the concentration is calculated. An automatic correction for pressure and temperature changes is possible. In addition, the transmission is displayed respectively output as a signal for preventive maintenance.
-
product
Fullband Coaxial Noise Sources
Our line of full-band noise sources are specially designed for easy integration into microwave systems. They feature rugged construction with excellent long-term stability. In addition to the RF output choices, there are also different packages available to meet a wide range of mechanical constraints. Typical applications include jamming, radar alignment, SNR testing and general lab use.
-
product
FAYb Laser Markers
LP-RF Series
Panasonic Industrial Devices Sales Company of America
The LP-RF200P Series FAYb Laser Marker features:- Compact IP64 Rated Head- Controller Offers High Resistance To Electrical Noise- Smart Functions To Adapt To Many Conditions- Direct Link To Image Processing Device- 17-Watt Fiber Laser- Removable Fiber Cable For Easy Installation
-
product
Integrated Laser Controller
ILC
AOSense has developed a compact Integrated Laser Controller (ILC) that can be paired with our External Cavity Diode Lasers (ECDLs) to control laser current, piezo transducer (PZT), and temperature. The ultra-low noise electronics are fully digitally controlled. The ILC dimensions are only 5″x2.9″x0.95″. We provide software with an easy-to-use graphical user interface (GUI) that can control multiple lasers from a single window. If preferred, commands may be sent over a USB virtual COM port. The software screenshot below (click the image to enlarge) shows the interface including a plot of the temperature (green line) as it settles to a commanded value.
-
product
Thermopile Laser Power Measuring Heads
HP Series
The HP25S head is specially designed for portable applications through the use of a smaller heat sink. This gives the head smaller dimensions but means that high powers are only possible for a short time.?
-
product
Monochromatic High Power LED Light Sources
LS-HP1 Series
The LS-HP1 is a series of high-power, high brightness light sources for liquid light guides (LLG). It is characterized by its outstanding luminance and thus delivers very high light output from liquid light guides. The LS-HP1 works with the latest generation of high-power LEDs with up to 100W power from an area of less than 15mm². With the LS-HP1 series, we achieve the highest luminance levels through optimized optical coupling into the liquid light guide without heating it up too much. The LS-HP1 is available for liquid light guides with core diameters of 3 or 5mm.
-
product
Precision Voltage and Current Sources
VI-700
The VI-700 Voltage and Current Source is a versatile precision dialable or remotely programmable voltage and current source. Its three ranges provide up to 20 V full scale (200 V with the HV option), and down to 100 mV resolution; and 20 mA full scale down to 0.1mA resolution. Both voltage and current outputs are available simultaneously. The output is set by a range selector and thumbwheel switches in the LOCAL mode, or by a digital input at the rear panel. The REMOTE mode control can be a RS232 or IEEE-488 interface.
-
product
Laser Head Cable, 20 m
10881F
Provide reliable power with this spade lug connector that connects the laser head to multiple laser boards.
-
product
Fiber Optic Light Source
Fiber optic light source is a fiber optic test equipment to measure the fiber optic loss for both single mode fiber cable and multimode fiber cables; usually the fiber optic light source is used with the fiber optic power meters. This fiber optical light source can provide wavelength output according to the specific requirements including the 650nm red source, 1310nm/1550nm wavelength for the single mode fiber and 850nm/1300nm wavelength for the multimode fiber. Used together with our fiber optic power meter, they act as an economic and efficient solution for the fiber optic network works.
-
product
Osram Direct Emission Green Laser Diodes (510 - 530nm)
The Optoelectronics Company Ltd
The PLT3 520D laser diode can deliver 140mW pulses at 520nm with 8% efficiency, driven at 300mA at 50% duty cycle – OSRAM's previous limit was 80mW with the PL 520B. This new diode has been developed to work in MEMS-based scanners.
-
product
Programmable AC Power Source
6400
Chroma Systems Solutions, Inc.
The Chroma 6400 series Programmable AC Power Source uses state of the art PWM technology to deliver pure, instrument grade AC power at a very low cost never achieved before. The 6400 AC power source offers maximum rated power for any output voltage from 0 to 300VAC, at any frequency from 45 to 1K Hz. It is not only suitable for commercial applications (47-63Hz), but also for avionics, marine, military applications at 400Hz.
-
product
Laser Rotators
Suitable for a wide range of applications, GeoMax rotating lasers are true multi-purpose tools.
-
product
Enhanced UV Light Source
Model 30E
The Model 30E Enhanced UV Lightsource is highly efficient and may be utilized in a variety of applications. Light is collected by an ellipsoidal reflector and focused on an integrating/condensing lens array to produce uniform illumination at the exposure plane. This UV light source is available in various beam sizes up to 24 inches square with output spectra ranging from 220 nm to 450 nm, using the appropriate lamp (included). Output power ranges from 200 watts to 5 kilowatts. All OAI UV Lightsources are easily equipped with quick-change filter assemblies, enabling the user to customize the output spectrum with little effort. Optional remote exhaust fans are available.
-
product
Laser Photometer
8587A
The photometer owners asked TSI to develop a modern version of the Laser Photometer 8587 that retains data continuity with the original version. Without data continuity, vast amounts of legacy research would not be directly comparable to new research. The result was the Laser Photometer 8587A.
-
product
Blackbodies & Extended Area Sources
The Infinity Series of blackbody radiation sources and extended area sources combine leading edge technology with features that support the expanding test requirements of the latest high performance sensors. SBIR designs the most stable, uniform, accurate and highly emissive blackbodies available. SBIR now offers VANTABLACK®S-IR as an optional coating, providing the E-O test community an unprecedented flat plate source emisisivty. SBIR continues to offer blackbody systems that provide the test community with unequaled performance, reliability and ease of integration into test systems. Our blackbody family includes six different varieties to choose from. The Infinity line offers four types of precision blackbody systems and our extended area sources offer two additional types of precision blackbodies to support all levels of IR testing.
-
product
Laser Type Edge Detection Sensor
LD
Panasonic Industrial Devices Sales Company of America
The Panasonic LD Series Laser Type Edge Detection Sensor can easily measure the outer diameter of objects. It can also sense inclines, detect the notch of a wafer and judge the height of small objects.
-
product
NI-9375 , 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-01
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
product
Tunable Wavelength Systems (OPOs)
NT342 Series
NT342 series tunable laser system comprises a nanosecond optical parametric oscillator and Q-switched pump laser in a single housing. The system features up to 50 mJ in VIS, no-gap wavelength tuning from 192 nm to 2600 nm, up to 30 Hz repeptition rate, easy maintenance and separate output for pump laser beam.
-
-
product
Open Source Real-time Network Topology & Protocols Analyzer
Skydive
Skydive is an open source real-time network topology and protocols analyzer. It aims to provide a comprehensive way of understanding what is happening in the network infrastructure. Skydive agents collect topology informations and flows and forward them to a central agent for further analysis. All the informations are stored in an Elasticsearch database. Skydive is SDN-agnostic but provides SDN drivers in order to enhance the topology and flows informations. Currently only the Neutron driver is provided but more drivers will come soon.
-
product
Laser Sources and Amplifiers
We design and manufacture a range of tunable C-band and L-band telecom laser sources, customizable fixed-wavelength laser sources, broadband super luminescent (SLED) sources, swept laser sources, and Erbium-Doped Fiber Amplifiers (EDFA).
-
product
Laser Head
5517D
The Keysight 5517D is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
product
3,000 AMP PORTABLE POWER SOURCE WITH JUMP START FUNCTION
VERSAPRO3
Multi-function portable power you can take anywhereDesigned to jump start cars, trucks, motorcycles, boats, ATV’s and moreVehicle jump starting and device charging capabilities for all of your portable power needs
-
product
Multi-Cluster Sources
Our complete line of sources can be configured in a Tri-Source configuration. Clustered sources are a vital part of effective seismic exploration. The destructive effects of the air blast associated with a discharging air source are made worse by clustering. In order to maintain the separation between air sources within a cluster, it is necessary to mechanically constrain the sources with rigid bars.
-
product
Source of Signals
CRS+
The CRS+ is a stable and calibrated source of signals which cover the 9KHz - 30MHz frequency range. The fundamental signal is a 15KHz comb and each harmonic is output as a narrowband peak of known amplitude. This signal is output on either the L and N lines, referenced to ground. A switch provides on/off and line selection.
