MIxed Signal Test Systems
See Also: Mixed Signal, Mixed Signal ATE, Mixed Signal Oscilloscopes, Mixed-Signal Test, Mixed Signal Testers
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White XLPVC, Single-Ended (1.5 Amps)
7-121966000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 26 AWG White XLPVC, Single-Ended (1.5 Amps).
-
Product
EBIRST 200-pin LFH To 160-pin DIN Adapter
93-002-410
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
783126-02
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
Smart Aircraft System
System
The Astronics Smart Aircraft System makes that possible. Our patented system enables the immediate, cabin-wide gathering of thousands of data points using sensors & IoT (Internet of Things) technology. The result? You get the insightyou need—when you need it. Insight that helps you on every flight. Insight that allows you to improve your operational efficiency, your cabin safety, and your overall passenger experience.
-
Product
SMD Test Fixture
16034G
Test Fixture
Perform impedance evaluation on a minimum SMD size of 0.6(L) x 0.3(W) [mm]
-
Product
Functional Test for Engineering Lab
Spectrum BT
Functional Test
Designed to meet the needs of product engineering labs, production lines, test development centers, and repair depots, the Spectrum BT is a configurable and scalable functional test system. This focused system solves typical functional test coverage challenges throughout the defense/aerospace product life cycle—and it’s upgradable as test requirements evolve.
-
Product
Airframe Electrical Power Systems
System
Rely on Astronics CorePower® airframe electrical power systems, where solid-state technologies deliver highly efficient, clean power that improves aircraft operation through weight and system wiring savings.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Lighting Systems for Aviation
System
Flying on every major platform, Astronics offers decades of proven experience in delivering standard and custom lighting solutions that illuminate the world’s aircraft. From commercial to business to military, chances are we offer experience with your type of fixed-wing or rotorcraft program.
-
Product
Signal, Patchcord, Receiver, 36", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps)
7-104872596-036
Signal Patchcord
Signal, Patchcord, Receiver, 36", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps).
-
Product
Spring Clip Fixture
16092A
Test Fixture
Use this test fixture with parallel electrodes for impedance evaluation of both lead and SMD components.
-
Product
Simulation Systems
System
Bloomy offers Simulation Systems for Hardware in-the-Loop (HIL) and open loop test of electronic controls and mechanical actuators for all types of transportation and defense systems including aircraft, rail, automobiles and ships. These systems, now deployed at major aerospace, locomotive and military manufacturers and research facilities worldwide, provide world-class, high-fidelity simulated environments for use in both closed-loop and open-loop testing. Because Bloomy’s Simulation Systems are largely constructed from COTS components, time to first test can be reduced significantly, and their highly-customizable nature allows your test system experts to provide your unique IP to differentiate your product from your competitors.
-
Product
Battery Management (BMS) Environmental Test System
Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
Product
Source / Measure Unit (SMU) Modules, N6700 Power System
System
The Keysight N6780 family of source/measure units (SMUs) provide advanced features and precise control and measurements of voltage and current down to the microampere and nanoampere regions. They provide stable, glitch-free output voltage and current during high-speed load changes, fast output modulation, and high-speed measurements of both voltage and current simultaneous.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-04
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXIe-5667, 3.6 GHz PXI Vector Signal Analyzer
782366-03
Signal Module
PXIe, 3.6 GHz PXI Vector Signal Analyzer - The PXIe‑5667 is optimized for spectrum monitoring applications such as radio monitoring, interference detection, spectrum regulation, and related applications in line with ITU recommendations. It features real-time signal analysis and advanced signal processing using the capabilities of the built-in FPGA. Additionally, the PXIe‑5667 includes options for various frequency ranges and instantaneous bandwidth.
-
Product
Design for Testability (DFT Test)
test
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
Product
Signal, Patchcord, ITA, 36", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-103922000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", TriPaddle, 22 AWG White, Single Ended ( 5 Amps).
-
-
Product
6TL10 Table Top Test Base
H71001000
Test Platform
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettes.The platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
Flex Socket Test Module
JT 2127/Flex Socket Test Module
Test Module
The JT 2127/Flex STM memory socket tester is a family of hardware adapters specifically designed for the testing of of PCB-mounted DIMM & SODIMM sockets using a JTAG/boundary-scan controller and supporting software. The testing of memory sockets has always been troublesome for test and production engineers using JTAG/boundary-scan systems. Even when it is possible to create memory writes/reads from a boundary-scan compliant access device on the UUT (Unit Under Test), the initialization process may fail leaving you with little diagnostics information. What’s more it can still be uncertain whether fault lays with the DIMM module itself or the socket. Using the new JT 2127-Flex system from JTAG Technologies you get pin-point diagnostics from a known-good test interface so you can be certain that your socket is soldered correctly.
-
Product
In-Circuit Tester
Sparrow MTS 30
In-Circuit Test System
The Sparrow MTS 30 is a 19“ test system that can be integrated into any standard rack. The In-Circuit tester can also be used as benchtop test system. With this compact and flexible tester you can perform both analog and digital In-Circuit and functional tests.
-
Product
20GHz Single Channel MW Signal Generator 19" 1U Rack
LSX2091R
Signal Generator
The LSX2091R is a 20GHz Single Channel Microwave Signal Generator, offers industry leading performance, in a 1U, 19” rack-mounted box. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The design offers excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
Product
Test Handler
M4841
Test Handler
High-Throughput Device Handler for Volume Production Testing of MCUs and DSPs.
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784777-01
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Test Fixture
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
Product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
test
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
Product
12GHz Single Channel Portable Signal Generator
LS1291P
Signal Generator
The LS1291P, 12GHz Single Channel RF Analog Signal Generator, offers industry leading performance, in a modern tablet like design that can be used as a benchtop or portable unit. The LS1291P features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS1291P was designed to offer excellent performance and meet today’s most demanding applications, whether in the lab or out in the field.
-
Product
PXI Breadboard Module, 2-Slot, No Connector
40-220A-102
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
PXI Breadboard Module, 1-Slot, 9-Pin D-Type
40-220A-701
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
