Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
-
Product
RF Constellation Simulator
GSS9000
-
The GSS9000 Series multi-frequency, multi-GNSS RF constellation simulator is the most powerful simulation system available.
-
Product
Environmental Testing
-
Among AMERICAN TESTING LABORATORY's environmental chambers is a walk-in stainless steel chamber, which is 40 feet long, 20 feet wide and 8 feet high. One of the largest environmental chambers owned by an independent testing organization in the nation, it allows for simulated environmental testing under conditions ranging from subzero to 200° F with a relative humidity of 5% to 100%, with a ±2% tolerance.
-
Product
Battery Simulator SoftPanel
A170202
Battery Simulator
For the products developed to connect batteries for use, if the battery is not ready or unable to be provided due to high cost, the 17020 battery simulator can be used to confirming the product functions during development. The applications of battery simulator include motor drives within the car system, OBC, D-D convertor or charger within the CSS system and products of DC bus, etc.
-
Product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
-
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
Product
NI Software Suites
-
NI software suites aggregate the most popular LabVIEW add-ons and other application software typically combined with LabVIEW and other development environments to help you build test, design, and control applications. Each suite, excluding the Multi-IDE Bundle and the Software Platform Bundle, also includes one year of unlimited access to professional training and certification.The suites come with related NI device drivers and are shipped on USB 3.0 media to speed up your installation.The NI Automated Test Software Suite combines LabVIEW, LabWindows/CVI, and Measurement Studio with the TestStand ready-to-run, customizable test executive and the Switch Executive intelligent switch management and routing application to help you build manufacturing or production test systems.The NI Embedded Control and Monitoring Software Suite features LabVIEW and the recommended add-ons specifically for building embedded control and monitoring systems on NI reconfigurable I/O (RIO) hardware. The LabVIEW FPGA Module extends the LabVIEW graphical development platform to target FPGAs on NI RIO hardware, and the LabVIEW Real-Time Module builds on LabVIEW to deliver a programming environment for creating reliable, deterministic, and stand-alone embedded systems.The NI HIL and Real-Time Test Software Suite combines LabVIEW with VeriStand, a configuration-based software environment for efficiently creating real-time test applications. It also includes the LabVIEW Control Design and Simulation, LabVIEW Real-Time, and LabVIEW FPGA modules.To learn more about each suite, use the navigation options on the left side of the page.The mark LabWindows is used under a license from Microsoft Corporation. Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
-
Product
Bidirectional DC Power Supply
62000D
DC Power Supply
Chroma 62000D programmable bidirectional DC power supplies provide both power source and load characteristics. These two quadrant power supplies allow power from the DUT to be converted back to the utility grid and so are ideal for testing renewable energy power systems such as PV, storage, and EV inverters as well as a wide range of bidirectional power conditioning system (PCS) and may also be used as a battery simulator.
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 31.5Ω
40-252-010
Programmable Resistor Module
The 40-252-010 is a programmable resistor module with 4 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
Walk-In Solar Spectrum Test Chamber
-
WEIBER walk in Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. It is also called Walk in Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Solar spectrum chamber also known as Walk in Solar Simulation Test Chamber
-
Product
KMD540 Series and RDR2000/2100 Panel
TA-3C
-
The TA-3C test fixture is a combination of the KMD540 testing requirements and the RDR-2000/2100 weather radar interface requirements. This panel allows the technician to test the KMD540 MFD as a stand alone item (with external simulators) or together with a radar sensor for a dynamic real time test. The panel includes the required switching for sensor alignment and KMD testing along with input jacks for the required data inputs. Also built into the fixture is an analog gyro simulator for checking the stabilization functions of the sensor. The full enclosure comes in standard panel width.
-
Product
Comb Generator
RefRad X
-
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm
40-294-031
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
-
Product
Real-time RF Channels Simulator
RF-LiveSim
-
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
Product
PXI Programmable Resistor Modules
Programmable Resistor Module
Part of our Sensor Simulation family, these PXI programmable resistor modules are ideal for medical, aerospace and automotive applications. A programmable resistor is designed to simulate the use of resistive sensors and variable resistors in systems when testing devices such as engine controllers.
-
Product
PXIe-7821, Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module
783485-01
Digital I/O Module
Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7821 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7821 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in-‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
Rapid Temperature Change Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Cover temperature,humidity, thermal shock with rapid temperature change rate, vibration testing. The simulation product detects whether the adaptability and characteristics of the product itself have changed under the combined conditions of temperature and humidity in the climate environment (high and low temperature operation & storage, temperature cycle, high temperature and high humidity, low temperature and low humidity, condensation experiment. etc.).
-
Product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-051
Programmable Resistor Module
The 40-297A-051 (PXI) and the 42-297A-051 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 2.97 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
CAN, CANopen, J1939 Tester
X-Analyser3
-
Warwick Control Technologies Ltd.
Graphical User Interface ideal for Windows PCs and tablets.• CAN, J1939, NMEA2000, CANopen, LIN and OBD – included into one tool• On-Board Diagnostics Scan Tool Features for Emissions ECUs.• CAN and LIN signal reverse engineering• Signals displays – text, scope and graphical such as gauges and lamps• Can be used for ECU or even network simulation• SAE J1939 database integrated with over 4000 PGNs and signals
-
Product
PXI Fault Insertion Insertion Switch Modules
-
Our PXI Fault Insertion Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect – all of which can simulate connectivity problems in the system.
-
Product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Flash Solar Simulators
-
Sciencetech manufactures a range of flash solar simulatorsSee the Flash Solar Simulator Overview to compare products across different product lines.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 239Ω
50-298-113
Programmable Resistor Module
The 50-298-113 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 239Ω with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm
50-293-012
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
C-SGN Emulator
-
The C-SGN Emulator combines the MME, SGW, and PGW functions, simulating the optimized EPC network required for CIoT. As part of the NetTest suite, the C-SGN Emulator creates an end-to-end lab environment for testing functions and features that characterize enhanced Machine Type Communication (eMTC) and Narrow Band Internet of Things (NB-IoT) implementations. In order to reduce complexity in the setup of a test environment, it also supports simulation of SMS Central Function (SMS-SC) and the Service Capability Exposure Functions (SCEF).
-
Product
PMC Intelligent Interface Card
IIB-1553-PMC
-
The IIB-1553-PMC is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the PCI Mezzanine standard, with 1553A, 1553B, McAir and STANAG 3838 variants in one card.
-
Product
GPS Simulator
ADIVIC MP6220
Simulator
Multi-channel GPS simulator for GPS receiver position fix testIndividual channel is power adjustableSingle channel mode for receiver S/N ratio testTunable power output level from -160dBm to -55dBm
-
Product
ATCA 5U 16 Slot Mesh
1900001495-0000
-
The 5U 16-slot ATCA backplane is a Mesh, compliant to the PICMG 3.0 Rev 3.0 specification. Elma Bustronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
Product
MIMIC sFlow Simulator
-
MIMIC sFlow Simulator generates a variety of flows and enables you to fully test your applications. Since you have a complete control over generated flowsets you can easily verify that your graphing application is correctly displaying the values and your collector correctly collects precisely generated flowsets.
-
Product
Four-module test set
F8200
-
Use the F8200 Power System Simulator for testing single-phase conventional schemes, digital protection systems, and more. This four-module F8000-series instrument is available in four standard configurations of HVA Current, HVA Voltage, and Low-Density Logic I/O modules.
