-
Product
Pin-Pointing System
Protrac®
-
As precise as pre-location is, it will never be able to recognise the deviations of a cable route in the ground. These can only be detected by precise pin-pointing. With its protrac®, BAUR offers different solutions that combine acoustic and electro-magnetic cable fault pin-pointing, sheath fault location and tracing in a single system.
-
Product
PED Systems
Pulsed Electron Deposition
-
Is a process in which a pulsed (80-100 ns) high power electron beam (~1000 A, 15 kV) penetrates approximately 1 μm into the target resulting in a rapid evaporation of target material. The non-equilibrium heating of the target facilitates stoichiometric ablation of the target material. Under optimum conditions, the target stoichiometry is preserved in the deposited films. All solid state materials – metals, semiconductors and insulators, including those transparent to laser wavelengths in PLD – can be deposited as thin films with PED. By combining PLD and PED, the range of complex materials that can be prepared as thin films can be greatly enhanced.
-
Product
Belt Starter Generator Test Systems
-
D&V has developed 12 V, 48 V and higher voltage BSG and ISG testing systems for performance, endurance and production testing, complete with thermal chambers, chillers and assembly lines.
-
Product
System Module
CM AXIe-0
-
CM AXIe-0 is intended for use as part of AXIe-0 standard racks with the number of slots (slots) no more than 14. CM AXIe-0 meets the requirements of the AXIe-0 standard for system modules of the AXIe-0 trunk.
-
Product
Portable Telemetry Systems
-
Lumistar’s portable receivers and test transmitters take the state of the art technology found in the PCI receivers and simulators and install it into a hand held units. Our luggable Telemetry Systems can be configured using our card level products into unique custom solutions.
-
Product
ATE System Power Supplies
N8700 Series
-
The Keysight N8700 Series ATE system power supply delivers high current with low noise in a compact two unit package. Airflow moves front to back, so no additional space is required above or below the power supply in your automated test equipment (ATE) rack. This series of programmable power supplies sources up to 3300 or 5200 W. Get output voltages from 8 to 600 V and 5.5 to 400 A.
-
Product
Full-Featured Life Cycle Test System
LCV
-
Configurations for testing to industry standards: IEC, SAE, BCILife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
Product
Power System Simulator
F6150sv
-
This power system simulator performs the simplest through the most complex tests. The F6150sv has the highest output current of any test set on the market – all within a single box.
-
Product
Brake Test Systems
Giant 8000 Series
-
Customer perception of vehicle quality is closely related to the NVH behaviour of the vehicle. With the HORIBA ATS Brake testing system, NVH relevant design features are analyzed and various metrics stored in the database of the automation system. For friction borne vehicle NVH problems coming from the brake and its components the GIANT 8000 Series is the ideal tool to resolve it. The GIANT 8000 Series is superior NVH test system providing you with the best testing conditions for all types of vehicles. Test brake fixtures could be tested with a complete wheel suspension system. In a semi acoustic chamber NVH tests could be realized and drum brakes and disc brakes including the vehicle axle could be tested.
-
Product
Curing Systems
-
Manufacturers know that the coating, dispensing and/or potting process doesn't end once the material is applied. Most materials require some sort of finishing step, or cure force, to dry, harden or cure the coating. For those materials that require thermal or UV cure forces, SCS manufacturers cure systems that are robust, reliable and ensure that your process is as efficient as possible.
-
Product
Test Line • Equipment For Testing For Function
-
The test equipment is used for qualitative functional testing of discharge power supply units and / or ionization units from the static line and air line (discharge). The devices are usually operated with a single button and indicate via LED, whether the device under review functions properly.
-
Product
Phase Noise Test System
PN9000 System
-
Noise eXtended Technologies S.A.S.
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range. Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a NIST tested instrument.
-
Product
Corrosion Test
-
The purpose of this test is to determine the resistance of materials and protective coatings to corrosive atmospheres when a more corrosive environment than the salt fog/spray test is required. The test is used when material is stored or operated in areas, for example, where acidic atmospheres exist, such as in industrial areas or near the exhausts of any fuel-burning device. Gases such as sulfur dioxide are used to replicate the exhausts of fuel burning devices.
-
Product
Wireless/RF Testing
-
NCEE’s experienced iNarte EMC/EMI qualified staff provide wireless and radio frequency (RF) testing of intentional radiators to ensure they meet the FCC, CE, and many other international regulatory requirements for transmitting and receiving (radio) devices. Frequent regulatory changes and complex testing requirements are common with wireless/RF equipment. NCEE Labs stays current with the most recent requirements and can help you navigate your requirements while supplying quality testing services to demonstrate worldwide compliance!
-
Product
Sound Level Meter Software
SLM Utility-G4
-
G4 LD Utility is the next generation Larson Davis utility software that provides new functionality and a modern interface.
-
Product
Blockchain Testing
-
ZenQ’s BlockChain Testing Centre of Excellence provides Testing services for Blockchain platforms and implementations.
-
Product
ICP Microphone System
HT378B02
-
This model includes a 1/2" microphone cartridge, a mated preamplifier with TEDS, and system calibration. Click the following for individual component information.
-
Product
Performance Testing
-
Performance testing is the best way to give your product a competitive edge. We offer performance testing for virtually any type of products, testing to national, international, or industry standards, as well as retailer, or your own, specifications.
-
Product
EO/IR Surveillance Systems
-
Multi-sensor systems for perimeter surveillance, security and force protection are available in a variety of lens and sensor combinations, and can be customized to meet any mobile or stationary mission requirement. These systems may be operated independently or in a fully integrated sensor network.
-
Product
Nitrogen Purging System
-
Manufacturer of a wide range of products which include Automatic Digital Nitrogen Purging System, Analog Nitrogen Purging System and Portable Nitrogen Purging System.
-
Product
ATE System Power Supplies
-
For more than 50 years, Keysight's automated test equipment (ATE) power supplies have changed the way engineers prove their designs, understand issues, and ensure product quality. Our programmable ATE system power supplies' compact design makes it easy to integrate them into any system. Keysight power supplies make it easy to update a test program with modern interfaces, LXI-core capability, and SCPI language. Accelerate test time with fast command processing and quick settling times.
-
Product
COMINT Monitoring System
-
A modern COMINT system can handle thousands of parallel signals. With a reliable and intuitive management software, the increased situational awareness creates a firm base for any decision making
-
Product
CUSTOM SYSTEMS
-
Tristan’s specialties include custom systems (magnetic, cryogenic, scanning, multichannel SQUID, variable temperature systems, magnetic fields, and microwave) based on a core technology of system building and expertise in cryogenics, refrigeration, software (upper level control and embedded) and electronics design.
-
Product
Test Fixture
OCP NIC 3.0
-
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
Product
HDT & Vicat Systems
-
The Instron line of CEAST Thermo-mechanical systems are used to characterize the behavior of plastic materials at high temperatures, measuring the heat deflection temperature (HDT) and the Vicat softening temperature (Vicat). These HDT and VICAT testers range from very simple units for quality control labs to more advanced and automated systems.
-
Product
Temperature Measurement System
TMM-100
-
Thermal Engineering Associates, Inc.
The self contained TMM-100 module accepts diode, thermocouple and thermistor temperature sensors. The USB-connected instrument is supplied with Windows™ 7, 8 & 10 compatible software that provides for sensor measurement on a cyclic basis and for data logging of all measured values. LabVIEW™ Virtual Instrument (VI) drivers are available as an extra cost option for users that wish to incorporate the TMM-100 into an application-specific measurement environment.
-
Product
Analyzer System
Ruggedized Test Systems (RTS)
-
This analyzer is a rugged, field deployable system that detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex.
-
Product
Spring Impact Hammer IK Level Tester
IK01-06
-
The most of luminaires manufactory were request to do IK level test (Impact Protection), LISUN can supply the IK test instrument. IK ratings are defined as IKXX, where “XX” is a number from 00 to 10 indicating the degrees of protection provided by enclosures (including luminaires) against external mechanical impacts. The different IK ratings relate to the ability of an enclosure to resist impact energy levels measured in joules (J). IEC 62262 specifies how the enclosure must be mounted for testing, the atmospheric conditions required, the quantity and distribution of the test impacts and the impact hammer to be used for each level of IK rating. The IK test applicate on lighting luminaires test according to IEC60598 (GB7000) and IEC60068-2-75 (GB2423.55).
-
Product
Insulation Testing
-
Weshine Electric Manufacturing Co., Ltd
Insulation is one of the most important constituents of a transformer. Any weakness in the insulation may cause failure of transformer. To ensure the effectiveness of the insulation system of a transformer, it must confirms the dielectric test. But the power frequency withstand test alone can not be adequate to demonstrate the dielectric strength of a transformer.
-
Product
Qualification Testing
-
Teledyne Storm Microwave ensures your design specifications are met by conducting in-house testing at all production phases. This comprehensive qualification process guarantees high-quality performance and reliability in every cable assembly, meeting the stringent requirements of your application.
