Phase Noise
Random variations of a signal's frequency.
-
Product
Cable Identification & Phasing
VCi-3™
-
The VCi-3™ system is designed for cable and phase identification, mainly for installation or maintenance purposes on three-phase electrical networks during power shutdowns.The transmitter module injects a low current on the cable conductors by direct contact or magnetic clamps methods. A voice message is recorded by the user and will be transmitted along with digital signals. Groundings stay connected at both ends of the three-phase circuit during the test. The detector module is used at the other end of the cable system.
-
Product
Phasing Meters
-
A unique tool in that it may be used as a conventional phasing meter, or the meter probe may be used as a stand-alone voltage detector on primary or secondary voltages or capacitive test points.
-
Product
Low Noise Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
KeyLink's low noise amplifiers typically exhibit noise figures below 5.5dB and output 1dB compression points up 8dBm. These amplifiers are economical choices for general purpose applications. KeyLink's low noise amplifiers can be categorized as follows.
-
Product
Power Phase Converter Single phase 220VAC to 3 phase 380VAC Converter
SDT-40KW
-
Zhejiang Sandi Electric Co., Ltd
SANDI SDT series single-phase to three-phase converter, adopted SVPWM modulation control technology, which can convert ordinary single-phase power to industrial three-phase power. After through SDT series single-phase to three phase converter power conversion, the three-phase power output is standard pure sine wave, the harmonic distortion rate (THD) is less than 2%, totally meet the national standards of three-phase power quality, applicable to all types of load.
-
Product
Low Noise Amplifier
LNA
-
Teledyne Defence & Space (TDS) Low Noise Amplfiers (LNA) are designed to amplify very low power signals without degrading the signal-to-noise ratio.An amplifiers is designed to increase the power of both the signal and the noise however the Low Noise Amplifier is specifically designed to minimise the additional noise so important information should not be lost.
-
Product
Optical Noise Analyzer
A0040A
-
Optical Noise Analyzer is the industry first solution for evaluation of optical frequency noise of lasers as power spectrum density.
-
Product
Antenna Noise Canceller
ANC-4
-
The ANC-4 is an rf device that eliminates or reduces power line noise, BPL noise, computer noise, TV-generated interference, and other types of electrical noise. The ANC-4 unit connects right to the antenna connector of the receiver or transceiver to cancel locally generated noise before it gets into the receiver and affects the receiver AGC circuits.
-
Product
Noise and Vibration Testing
-
Electronic Systems of Wisconsin, Inc.
ESW's unique Noise & Vibration Test Systems come fully equipped with the latest industry features. The on-screen operator display in our testers make it easy to set-up, read, track and record your noise or vibration information. We work directly with you to determine the best solution that will work for your application. Our data logging make sure that important data is stored and available for download for future reference. ESW's design engineers work to make sure the testing interface is easy for your operators to use. We work closely with our customers to make sure that your unique testing needs are met. Please see the slideshow below to see some of our Noise & Vibration Testers.
-
Product
Noise Sources
-
This power amplifier ensures that you get the maximum sound pressure level out of the Norsonic range of speakers.
-
Product
Digital Phase Shifter
-
Analog Devices digital phase shifters change the phase of RF, microwave, or millimeter wave signals while providing no amplitude change. They are used in a variety of applications, including RF PA linearization/RF distortion, amplitude and phase modulation, variable attenuators, and fiber optics.
-
Product
Three Phase Tester
4200
-
Peaceful Thriving Enterprise Co Ltd
*Fast and accurate measurement.*Portable and compact design, easy to carry.*Efficient, effective, reliable, easy and safe to use.*Two function in one unit. Including open phase and phase sequence.*This is idea for installing conveyor lines, pump systems and interconnected drivers.*Indicate phase orientation (clockwise or counter-clockwise) and whether each of three phases is live.
-
Product
Noise Monitoring Systems
-
It delivers 24/7 connectivity, continuous power capabilities, and a rugged design to simplify your long-term testing.
-
Product
Phase Detectors
-
Macom Technology Solutions Holdings Inc.
MACOM's MSPD Series Integrates an SRD reference frequency multiplier, coupling capacitors and a Schottky diode microwave sampler / phase detector in a 0.075” by 0.100” hybrid. They are used to phase lock microwave oscillators up to 22 GHz to a much lower reference frequency by deriving a locking voltage from the sampled RF and the multiplied reference.
-
Product
Ultra-low Noise Phase Inverter - Buffer
WMA-IB-LN
-
The WMA-IB-LN can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision and ultra-low noise. The WMA-IB-LN model has been designed specifically for the Falco Systems WMA-200 high voltage amplifier. Two WMA-200 amplifiers combined with one WMA-IB-LN provide unprecedented noise performance and output voltage range.
-
Product
Ultra Low Noise Preamp
J2180A
-
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
Product
Phase Detectors
CD series
-
The CD series is a phase detector module. It is possible to detect small level signal and signal buried in noise.
-
Product
Multi-Channel Automotive Noise Finder
7633A
-
Peaceful Thriving Enterprise Co Ltd
Multi-Channel automotive noise finder is a portable equipment to diagnose the defect of the vehicle. When the generator is running, it can detect the impact and vibration due to the defect and failure of bearing, gear, valve, crank, cylinder, gear box, and vehicle body…etc. With this equipment, the repairer can clearly locate which part of the machine cause the noise and how serious is it; even though the repairer operates the equipment in a very noisy environment.
-
Product
Phase Shifters
-
Phase Shifters continuously change the phase of a microwave signal by applying a varying DC current, voltage or digital signal, depending upon the model type selected. Customized features are highly sought after designs, comprising a great majority of products in existence.
-
Product
Noise Source
MNS-1
-
Matrix Test Equipment Incorporated
The MNS-1 is a shaped noise source that can be used toemulate 2 bands of digital carriers. While it does not havethe necessary attributes to generate a constellation, it doesmimic the loading of QAM carriers. The MNS-2 featuresremotely controllable 6 MHz wide notch filters to allowintroducing a QAM carrier capable of generating a constellationand enabling measurement of Modulation Error Ratio (MER) andBit Error Rate (BER).
-
Product
Noise Receiver Modules And Noise Switching Modules
MT7553 Series
-
Noise Parameters are the non-50Ω extensions of Noise Figure, and are an important modeling and model validation tool to understand how a device-undertest’s performance changes as a function of source impedance. Noise Parameter measurements are typically performedusing a Vector Network Analyzer (VNA) to measure the S-Parameters of the DUT, and a Noise Analyzer (either Noise Figure Analyzer NFA or Spectrum Analyzer SA) to measure the noise power of the DUT. Noise parameters are calculated from a combination of knownsource impedances, S-parameters and noise powers.
-
Product
ource Phase Control
S97088B S
-
The S97088B allows users to set calibrated, arbitrary phase differences between two signal sources running on the P50xxA Streamline VNAs.
-
Product
Three Phase Load Bank
REOLOAD 310
-
A three phase load bank rated for 48kW, with fan cooling. The front panel layout includes a switch panel for configuring the separate resistor modules to give the required resistance and current range. There are also digital panel meters for displaying the phase voltages and currents. An interface for PLC control is also provided.
-
Product
Precision Pink Noise Generator
Noise Plug
-
The NOISE PLUG is a complete precision pink noise generator built in a XLR microphone connector. Inside the NOISE PLUG is an ultra wideband, avalanche junction white noise source.
-
Product
Phase Shifters
-
Essential function blocks such as Teledyne Microwave Solutions' Phase Shifters provide reliable, high performance for RF/Microwave commercial, industrial and military systems.
-
Product
Single Phase Relay Tester
PTE-100-V
-
The unit is extremely compact and rugged. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability. This technology allows users to test many different specific functions required in relay testing, without the need of additional accessories.
-
Product
Phase Shifter
-
A microwave network module which provides a controllable phase shift of the RF signal.
-
Product
Online Noise Monitor
AWA5636-3
-
Hangzhou Aihua Instruments Co., Ltd.
Complies with IEC 61672 Class 2. Uuse in Noise On-line Monitoring, Connect to Noise Screen
-
-
Product
Low Noise Prepolarized Microphone
378A04
-
The 378A04 is a matched system that is comprised of a high sensitivity microphone and a low noise preamplifier that contains a built-in filter that enables the free-field response to remain flat over a wide frequency range. The system requires a minimum of 4 mA and measures to 6.5 dBA (5.5 dBA typical) within a cost efficient, prepolarized (0V) design. PCB's model 378A04, the industry's first prepolarized low noise microphone and preamplifier system allows you to measure extremely low amplitudes. In the past this was only possible with externally polarized solutions. With a typical noise floor of 5.5dBA, this microphone system delivers all of the benefits commonly associated with prepolarized systems.
-
