Filter Results By:
Products
Applications
Manufacturers
EM
-
product
High Frequency Electromagnetic Software
Sonnet Suites
The Sonnet® Suites™ develop precise RF models (S-, Y-, Z-parameters or extracted SPICE model) for planar circuits and antennas. The software requires a physical description of your circuit (arbitrary layout and material properties for metal and dielectrics), and employs a rigorous Method-of-Moments EM analysis based on Maxwell's equations that includes all parasitic, cross-coupling, enclosure and package resonance effects.
-
product
TEM Antenna
TEM antenna is a broadband antenna with a flat response which makes TEM suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain. Its compact and robust design (passive sensor) makes TEM the optimal sensor for direct installation on medium voltage Switchgears and motors. It can be virtually applied in any electrical equipment provided that it has apertures or EM transparent surfaces.
-
product
Time Domain Sensors
TDS
Schmid & Partner Engineering AG
Time Domain Sensor (TDS) probes are miniaturized fully isolated active optical magnetic or electric field sensors operating in the frequency range from 10MHz to 6GHz. TDS offers unparalleled sensitivity for EM measurements resolved in the time and frequency domains while maintaining all amplitude and phase information.
-
product
Shielding Effectiveness/ Conductivity Test
EM-2107A | 30 MHz – 1.5 GHz
The EM-2107A is a standard test fixture for evaluation of the electromagnetic shielding effectiveness of planar material. The fixture is an enlarged section of coaxial transmission line and complies fully with the requirements of ASTM test method D4935-1. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred. The EM-2107A is provided with a reference standard test specimen, a dynamic range specimen. Dynamic range of greater than 80dB is achievable, although the cables and other test system components usually establishes the limiting factors.
-
product
Power Relays
Replace your large, slow, unreliable EM relays with the Ideal Switch. Enable a new era of connected and better protected buildings (residential, commercial, hospitals, airports), transportation (eMobility, Rail, Marine), factories (Robots and Systems), and power distribution (solar, wind, grid, battery).
-
product
Horn Antenna
Horn antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in electric assets like GIS and GIL or MV and HV power transformers. It is a broadband antenna with a flat response which makes Horn antenna suitable in a number of different applications. It has been optimized to operate in a frequency range suitable for PD activity monitoring and it was designed to provide maximum sensitivity and high gain.
-
product
Free Feature-Limited Version of Sonnet''s Professional Sonnet Suite
Sonnet Lite™
Sonnet Lite™ is a free feature-limited version of Sonnet''s professional Sonnet Suites, which provides EM analysis to thousands of companies across the globe. Many major manufacturers of high-frequency components and boards depend on Sonnet to analyze their predominantly planar high-frequency designs from 1 MHz through several THz.
-
product
Circuit Synthesis Software
Optenni Lab
Optenni Lab™ is the leading circuit synthesis software for antenna optimization aiming at efficient assessment and optimization of antenna systems at any design phase. Optenni Lab features automatic matching circuit synthesis and optimization, antenna array beamforming with active impedance control, and many supplementary assessment tools. Optenni Lab is often used in conjunction with EM simulators, and several links are provided with major EM tools on the market.
-
product
Transient EM System
TerraTEM24
The new generation terraTEM, the terraTEM24, has been designed to acquire high‑quality transient electromagnetic data from a wide variety of sensors ranging from remote inductive and B field sensors through to single loop and coincident loop configurations.
-
product
Operator Interfaces
Watlow Electric Manufacturing Company
Watlow offers reliable, affordable, easy-to-use interfaces for machines and systems. The Silver Series EM touchscreen operator interface terminals feature e-mail, USB, data logging, password security and multiple languages. The EZ-ZONE RUI remote user interface fits in tight spots, its EZ-Key reduces repetitive tasks to one touch and the gateway options connect EZ-ZONE products with other automation equipment and software. Paired with Watlow controllers, these interfaces are the perfect solution for process and machine control applications.
-
product
Electron Multiplication (EM) Standard Image Sensors
EM (Electron Multiplication) is a technology that uses on-chip gain in the charge domain to effectively eliminate read noise from an image sensor. This enables advanced ultra-low light applications that require extreme sensitivity at fast frame rates. Examples include life science applications such as single molecule detection, super resolution microscopy and spinning disk confocal microscopy along with physical science applications such as nanotechnology imaging, Bose Einstein condensates and soft X-ray spectroscopy, and astronomy applications such as adaptive optics and lucky imaging. The inclusion of an additional conventional output allows further flexibility for applications such as true 24 hour surveillance.
-
product
Propagation Software
Wireless InSite
Wireless InSite is a suite of ray-tracing models and high-fidelity EM solvers for the analysis of site-specific radio propagation and wireless communication systems. The software provides efficient and accurate predictions of EM propagation and communication channel characteristics in complex urban, indoor, rural and mixed path environments.
-
product
EM Tracking Products
The strength of the Aurora and 3D Guidance electromagnetic tracking solutions lies in their similarities and their differences. Both can provide unobstructed in-vivo tracking of OEM medical instruments, share exceptional measurement accuracy and reliability and are engineered and manufactured to deliver unparalleled tracking performance. Between them, there are seven different field generators with unique measurement volumes, and 20 standard sensor offerings (plus custom options). While the Aurora has 6DOF and 5DOF sensors, the 3D Guidance solution specializes in 6DOF tracking. 6DOF sensors are usually re-processable; 5DOF can be disposable. Some of our field generators are portable, while others seamlessly integrate into the medical OEM’s procedural cart or operative table. These differences provide near-countless opportunities to customize and integrate the Aurora and 3D Guidance solutions – all while benefiting from a shared foundation of technical excellence and expert product execution.
-
product
EMCCD Image Sensors for Space and Ground-based Astronomy
EM (Electron Multiplication) is a technology that uses on-chip gain in the charge domain to effectively eliminate read noise from an image sensor. This enables advanced ultra-low light applications that require extreme sensitivity at fast frame rates such as adaptive optics and lucky imaging™.The combination of Teledyne e2v’s back-thinning technology and anti-reflection coatings enables industry leading quantum efficiency that can be optimised for applications in the visible, UV or NIR wavelength ranges.
-
product
Cable Harness EM Solver
MHARNESS
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
product
General Electromagnetic Model for the Analysis of Complex Systems
GEMACS
Applied Research Associates, Inc.
GEMACS' biggest advantage over other EM codes (NEC, BSC, Carlos-3D, etc.) is the availability of multiple physics and solution methods integrated into a single product, with a command and geometry language that lets the user and not the software direct the execution of a particular problem.
-
product
Laboratory EM current meter / water level and wave height meter
ACM2-RS and ACM3-RS are 2-D and 3-D electro-magnetic current meters for laboratory experiments. The models provide digital output, a high-speed sampling rate and insusceptibility to electro-magnetic noise. ACH-600RS is a highly sensitive capacitance water level meters. With the new system, a maximum of four different sensors can be connected to the compact interface unit, enabling simultaneous recording on a personal computer. Additionally, the system can provide analog output as well as necessary. While conventional water level and wave height meters cannot be used near velocity sensors, our instrument can be as near as 5 cm without increasing noise, due to its special isolated circuit. The result is an innovative system that is capable of achieving highly accurate data.
-
product
EM Solver System Level Solver
EMA3D
Electro Magnetic Applications, Inc.
MA3D is a powerful 3D numerical solution of Maxwell’s curl equations based on the time-domain finite-difference method in rectangular coordinates. The code has application to nearly any EM coupling, radiating, or interaction problem. EMA3D’s FDTD approach is the only EM tool capable of capturing the detail of entire aerospace or ground systems down to individual electronics interfaces in a computationally accessible manner. Computational advances and parallelization allow for fidelity once only dreamed possible.
-
product
Spiral Antenna
UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain.
-
product
Antenna
Our expertise in 3-D EM computation accelerates the antenna development through accurate simulations and performance optimizations with full CAD description of devices and precise definitions of materials.
-
product
Antennas
Is a specialized transducer that converts electric current into electromagnetic (EM) waves or vice versa.
-
product
CCCP Controller
CCCP is the technology behind Nüvü Camēras’ extraordinary sensitivity in low light imaging. The patented controller generates significantly less clock-induced charges (CIC) than any other CCD controller during charge transfer throughout the EMCCD (down to an average below 0.001 ē/pixel/frame), therefore allowing for greater EM gain to ultimately attain sub-electron readout noise.
-
product
Interference & Compatibility Evaluation System
ICEy
Schmid & Partner Engineering AG
ICEy is the most advanced reactive near-field E/H-field scanning system for the analysis of EM interference and compatibility (EMI/EMC) in highly integrated electronics. ICEy is the only system that provides accurate EM measurements traceable to international calibration standards and also allows independent interlaboratory comparability of EMI/EMC measurement results.
-
product
Navigation Information System
Nav-IS
Aeronautical & General Instruments Ltd.
Nav-IS combines a single or dual axis EM Speed Log with a range of Meteorological System options for a low cost, integrated solution. Using the latest proven and in service solid state sensor technology, this innovative, cost-effective and accurate system has been specifically developed for all applications from ocean-going merchant and passenger vessels to offshore patrol, coastguard and naval support vessels.
-
product
WIPL-D Pro CAD
WIPL-D Pro CAD
WIPL-D Pro CAD is the tool that introduced solid modeling into WIPL-D, allowing fast modeling and manipulation for a wide range of EM applications. The simulation itself relies on WIPL-D’s proven and powerful kernel. Import of various CAD formats, numerous built-in modelling primitives, Boolean operations, waveguide ports, and automated simulation‑optimized all-quad mesh are features turning WIPL-D Pro CAD into a full, powerful package for high-complexity modeling of EM problems.
-
product
Electron Microscope Sample Preparation
Excellent sample preparation is the prerequisite for first-class electron microscopy. Be prepared – for great results in EM Sample Preparation! Perfect preparation makes the difference between trying and achieving, between failure and success, between results and excellent results. So be prepared for great results with Leica Microsystems!
-
product
Transient EM System
terraTEM
The terraTEM is a robust transient electromagnetic (TEM) survey system which provides high resolution conductivity imaging. Applications for the terraTEM include mineral exploration, near surface applications including geotechnical and engineering investigations, groundwater and salinity studies, and environmental surveys.
-
product
RF Architectural Shielding Products
EMI (Electromagnetic Interference) is often used interchangeably with RFI (Radio Frequency Interference). However, EMI can be any frequency of electromagnetic noise, whereas RFI is a relatively narrow range of electromagnetic noise on the EM spectrum. EMI Shielding can be used to mitigate electric and magnetic radiation across various spaces. Radio Frequency (RF) Shielding can be used to mitigate RFI with specifically designed enclosures that can block RFI. As well, RF Shielding can include application of RF Shielding paints, fabrics, and other materials.
-
product
IQ Demodulator
IQD Series
*Capable of receiving RF and LO frequency inputs *Output from DC to 500 MHz *Internal low noise oscillator Internal reference *Buffered demodulator *Balanced IQ *Optimized for low EVm *Optional internal Reference Detect Switch (EM Research RDS Series) *Up to 250 mega-symbols per second
-
product
Sputter Coater & Freeze Fracture Solutions
To obtain high-quality images of samples with scanning (SEM) or transmission electron microscopy (TEM), your samples need to be conductive to avoid charging. If a sample does not have a high enough conductivity, then you can quickly cover it with a conductive layer using the method of sputter coating. Also, a carbon or e-beam evaporator coating can be used. Such coatings protect the sample, allow enhancing of the EM image contrast, or can act as a TEM-grid support film for small scale samples.
