Li-ion Battery
use lithium compounds as the anode.
-
-
Product
High-accuracy Dual-channel Programmable Battery Simulator
N8352 Series
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N8352 series is specially designed for the R&D and testing of portable, battery-operated products , such as Bluetooth headsets, mobile, AR/VR smart terminals, electrical tools, etc. The current flows in both directions and can be used as either a power supply or a load. N8352 is easy for operation with touch screen and UI design. The output features are comparable to actual batteries, with fast dynamic response, no overshoot in voltage rise and fall, and stable waveform. The resolution is up to nA level, which can test the loop static power consumption, etc. N8352 can be widely used in the area of consumer electronics testing.
-
Product
Automatic Battery
BATLV360
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
PulseTech Battery Analyzer, 6V and 12V Battery Tester
390PT
-
The 390PT Battery and System Tester lets you quickly, safely and accurately test both 6-Volt and 12-Volt lead-acid flooded, AGM (flat and spiral plate) and gel cell batteries in or out of the vehicle and test 12-Volt and 24-Volt charging systems for proper operation. Combined singe load, dynamic resistance technology and algorithms display battery voltage and capacity in easy to understand results in seconds. The handy "QUICK START" instruction guide is printed on the back of the tester.
-
Product
Motorcycle Battery Testers
-
ELAK Motor-Cycle Battery Testers are designed for testing batteries used in motor-cycles, scooters, ATV''s, etc. These testers check the voltage drop of the battery under a fixed load and confirm the status of the battery full, weak or dead. The new generation motor-cycle and scooters are fitted with an electrical start. It is therefore very essential to test these batteries under load, to ensure that the batteries are capable of starting the vehicle.
-
Product
Battery Cell Surge Tester
19311
-
The Chroma 19311 series battery cell surge tester is designed for testing the insulation quality between the positive and negative plates of the lead-acid battery cell. This is done by applying a high voltage surge/impulse before the electrolyte injection. Its output voltage can reach up to 6kV. It also has four terminal measurement and 200MHz sampling rate. The Chroma 19311 series has single channel (19311) and multi-channel (19311-10) tester.
-
Product
Battery Load Tester
BT-100
-
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
Product
Heavy Duty Circuit Tester with 12' Retractable Wire & Battery Clip
27300
-
Features an extra long wire that stretches up to 12 feet for use, then automatically retracts. Quickly and easily check electrical circuits and accessories on 6 and 12 volt systems. Great for use on cars, trucks, boats, trailers, motorcycles, airplanes and snowmobiles. Heavy duty ground clip with insulator. 3 1/4" standard length probe
-
Product
Battery Conductance Tester
BT-3918
-
Kongter Test & Measurement Co., Limited
The excellent performance of BT-3918 battery conductance tester will help you pick out the weak batteries and ensure battery performance in short time measurement. This test of battery internal resistance or battery conductance is essential for stationary batteries. It is also recommended by latest regulation of IEEE 450, IEEE 1188 and IEEE 1106.
-
Product
12V 0-500 Amp Carbon Pile Battery Load Tester and 12/24V Electrical Systems Tester
6042
-
• Test batteries up to 1000 CCA• Interprets data from the charging/starting system on easy-to-read LCD displays• Shows positive and negative amps for easy diagnosis of current leakage problems• 0-500 Amp variable carbon pile load tester• Unique curved carbon discs ensure maximum contact, fewer hot spots, smoother operation and longer life• Heavy-duty single extruded leads for testing up to 15 feet apart• Test electrical systems on 12/24 Volt systems• Test all battery types• Ideal for testing remotely mounted batteries accurately• INCLUDES: Model 6043 1000 Amp AC/DC Inductive Amp Clamp for checking starter draw or parasitic drain test, also can be used with conventional multi-meters; heavy duty, two wheel tilt-back cart with 8” wheels and 2 trays.• Made in USA of US and Global Components
-
Product
Computerized 8 Channels Battery Analyzer
BTS8-WA
-
BTS8-WA is a precision eight channels battery test system for measuring battery capacity at 0.002mA - 1mA up to 5V.. This systems the best tool to study new generation energy storage materials and rechargeable battery.
-
Product
Battery Starting & Charging System Analyze
12-2415
-
*Shown with optional 12-2416 barcode scanner*Graphical Hand-Held Tester with Thermal Printer and USB Port*Tests 12V Flooded, AGM, Gel Cell, & EFB Batteries from 100 to 2000CCA*Graphical/Symbol Based LCD display*Tests 12/24V charging and electrical systems*Stores last 70 test series with or without power*Carrying case, printing software and USB cables included*Built-in thermal printer with thermal paper (611305)*Field-Replaceable Cables (900165)
-
Product
In-Line X-ray Inspection System for Secondary battery
X-eye 9000 Series
-
X-ray Tube100 kV / 200 µAMin. Resolution5 µmInspection Ability120ppm , 150ppm, 180ppmSystemConveyor / Index / Pick&Place 방식 LoadingDimension1,800(W) x 1,560(D) x 2,070(H)mm / 5,000kg
-
Product
Battery Discharge and Capacity Testers
-
HD Power Test Equipment Co.ltd
HDFD Battery Discharge Tester can be used as the discharge load in the battery off-line state to realize the constant discharge at the set value by regulating continuously the discharge current. When discharging, the tester will automatically stop discharging when the voltage on the battery group terminal or the cell falls to the set lower limit value, or when the set discharging time is out, or when it reaches the set discharging capacity. Battery Discharge Tester can records all valuable and continuous real-time data during the discharge process.This tester system is simple, safe and accurate for monitoring voltage of cells adopting wireless connection.
-
Product
PathWave BenchVue Advanced Battery Test And Emulation Software For A Single Instrument
BV9211B
-
Achieve higher accuracy, repeatability, and safety with an emulation based on a unique battery model. Your model will allow you to determine your device's power consumption, emulate an actual battery, and import existing battery models.
-
Product
External Fire Exposure Test Machine, Battery Safety Testing
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL external fire exposure test machine is applicable to the standard UL 2580.
-
Product
Battery Fault Insertion Unit
Fault Insertion Unit
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
-
Product
Battery Capacity Tester
BLU-C Series
-
BLU-C is the latest solution from DV Power for conducting a comprehensive battery capacity test. This universal instrument is applicable to any battery string, such as lead-acid, Li-Ion, Ni-Cd, and others, with voltages up to 800 V DC.BLU-C tester simplifies battery testing in multiple ways. The instrument provides monitoring of discharge parameters (graphically and numerically) in real-time on a 7-inch touch screen display. The instrument also enables measurement and monitoring of cell parameters (voltage/intercell voltage/temperature), which makes it a complete stand-alone discharge test system.The capacity tester is compatible with DV-B Win software. Because of that, the user can view detailed numerical and graphical presentations of key parameters, and create reports in various formats.The capacity test is performed in a user-friendly way according to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22 and other.The battery tester enables setting the discharge current up to 300 A, with 0,1 A resolution. If higher currents are required, BLU-C units can be connected in parallel, or BXL additional load units can be used.The user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Testing can be carried out without disconnecting the battery from the equipment it supplies.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF800
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation ofpower factor in low voltage instalations
-
Product
Battery Monitoring System
-
JUNXY Battery Monitoring Systems are designed in accordance with IEEE Battery Maintenance recommendations. This allows you to maintain a safe and secure system with Real-time monitoring, which will minimize the probability of a failure and optimize the service life of the battery. JUNXY Battery Monitoring Systems not only monitor the batteries, but also the external parameters which could affect the performance of the system, providing added security. It is a powerful tool for mitigating and preventing costly downtime due to unexpected system failure.
-
Product
Battery Monitoring System
FST-TA
-
Foresight Electronics Co., Ltd.
Continuous 24/7 on-line monitoring One CELLCHECK monitor one cell, including internal resistance, voltage and temperature Software is available to collect data from CELLCHECK Serial port with Optical isolation, meet MODBUS protocol, easy to be accessed by UPS controller Easy to install without specialized training Full resistance, battery temperature and voltage monitoring for comprehensive battery state of health analysis String current and ambient temperature monitoring
-
Product
Emergency Battery Power Supply Test Fixture
TA-61
-
This test fixture provides an interface to test and chargethe Radiant type RPS1-B Emergency Lighting power supply. The panel includes the switching required asdescribed in the CMM along with an analog currentmeter for monitoring the charging current. This panelprovides simple testing for the corporate flight departmentor DOM.
-
Product
CTEK MUS 4.3 TEST&CHARGE Battery Charger and Tester
56-959
-
The MUS 4.3 TEST&CHARGE combines an advanced micro-processor controlled battery charger with a battery and alternator test function to provide the ultimate in battery testing, charging and maintenance.
-
Product
Battery Monitor Relay
BMR
-
The Battery Monitor Relay contains over under voltage sensors combined with positive and negative ground detection.
-
Product
Self-Rectified Generator Power Supply Crawler Battery 9 to 300 kV
SITEX C3003
-
Self-Rectified Generator Power Supply Crawler Battery
-
Product
Battery Formation and Testing System
BFS 2000
-
BENNING Elektrotechnik und Elektronik GmbH
For many decades now, BENNING has designed and manufactured charge/discharge converters for the battery industry. These converters are used in both the production and testing processes involved in battery manufacturing and for series-testing of batteries. BENNING's BFS battery production and testing system provides a solution which makes it easier to control and monitor production and test processes which saves both time and energy. When used in power stations and rail applications (mobile version), it can be used to test and maintain a wide range of battery types.
-
Product
Battery Portable Passive Intermodulation Analyzer
iPA Series
-
The iPA Series Passive Intermodulation (PIM) analyzer is the first battery powered PIM Test Analyzer versatile enough to support multiple test scenarios such as testing at the top of the tower, base of tower, roof top and in-building for DAS systems. This IEC compliant 20W, rugged, battery operated design includes a tablet computer in a ruggedized case for remote control. This allows hands-free dynamic testing that is safe and convenient. Add the optional Range to Fault (RTF) module to quickly identify the location of PIM and Return Loss sources.
-
Product
Temperature & Battery Testing
-
Conducted to determine how a battery performs under different temperature ranges.
-
Product
Battery Tester 12V Language
BT12L
-
The Battery Tester 12V Language (BT12L) is an inexpensive, simple and easy tool for testing automotive batteries. It has LED display that consumes very little current and will not drain the battery with repeated testing.
