Voltage Calibrators
An accurate voltage units of measure to facilitate comparison to and adjustment of instruments.
See Also: Voltage Sensors
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-341-HI
Programmable Resistor Module
The 40-230-341-HI (PXI) and 42-230-341-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 102kΩ with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Dielectric Withstanding Voltage Test
-
The dielectric withstanding voltage test (also called high-potential, over-potential voltage-breakdown, or dielectric-strength test) consists of the application of a voltage significantly higher than rated voltage for a specific time, between mutually insulated portions of a component part or between insulated portions and ground. This is used to prove that the component part can operate safely at its rated voltage and withstand momentary over-potentials due to switching, surges, and other similar phenomena.
-
Product
LXI High Voltage Matrix 2-pole 200x2
60-310-202
Matrix Switch Module
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
Multifunction Process Calibrators
-
Practical Instrument Electronics, Inc.
Tired of carrying large, cumbersome multifunction calibrators with their confusing buttons and menus? PIE multifunction calibrators are small, easy to use and extremely accurate. The unique and intuitive EZ-DIAL Double Click Menu makes them simpler to setup than larger calibrators with their complicated button filled panels and confusing menus. Use PIE right out of the box instead of wasting time learning to use more complex calibrators. PIE has a multifunction calibrator to fit your needs from the PIE 820 with a single display to the advanced troubleshooting capabilities of the PIE 830.
-
Product
Stand Alone Low Voltage Tester
TestMate 128
-
The TestMate continuity tester features a universal interface fixture that accommodates adapter cards for quick changes in harness setups. Adapters can be exchanged in seconds to adapt quickly to any of a variety of wire-harness/cable connectors.
-
Product
Electronic Calibration Module (ECal), 40 GHz, 2.92 Mm, 2-port
N4692D
-
The Keysight N4692D microwave electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4692D is a precision 2-port ECal module that supports 2.92 mm connectors up to 40 GHz. Select either female-female, male-male, or female-male connectors. The plastic storage case for the N4692D is included for securing your ECal module and accessories.
-
Product
Labconcept Horizontal Calibration Benches By Trimos
-
a remarkable instrument for all measuring tasks that require extremely high accuracy.
-
-
Product
ECPR System (Electrically Calibrated Pyroelectric Radiometer)
Rs-5900
-
Developed in conjunction with NIST, the Rs-5900 ECPR is a ±1% absolute accuracy radiometric transfer standard for the visible to near-IR (0.25-2.0µm), with the RsIR Option extending the ±1% accuracy to >20µm. The RsP-590 Pyroelectric Probe requires no cooling and maintains ±1% accuracy from 1 µW to 100 mW. The ECPR uses an auto-nulling, electrical substitution technique that allows the instrument to be referenced against NIST electrical standards, insuring maximum accuracy and precision. Unlike most electrically calibrated radiometers, there is a direct correlation between electrical and optical heating because the same material serves as both the optical absorber and electrical heating element.
-
Product
High Voltage Probe
HVP-40DM
-
*DC 40KV CAT II Pollution 2.*2000MΩ Impedance.*3999 LCD display.*Accuracy 1.0% full range.*T.C. 100 ppm/oC*400V/4KV/40KV, 3 range.*Resolution 0.1V/1V/10V.*PEAK HOLD, Auto power off.*CE, TUV GS, UL, CUL, IEC1010
-
-
Product
22-Pin REDEL High Voltage Cable Assembly, Male to Unterminated, Cut Ends, 0.25A, 1m
A022KMR-C-HA100
Cable Assembly
This is a 1m long male to unterminated 22-Pin REDEL high voltage cable assembly with cut ends constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips are provided to secure the connector to associated product.
-
Product
VLF Voltage Generators
-
Fivestar HV Testing Equipment Co., Ltd.
VLF hipot is an AC output tester with an output frequency of 0.1 Hz or lower rather than 50/60 Hz. Although the frequency is very low, it is an alternating current with polarity reversals every half cycle.
-
Product
WAVEPULSER-40IX + WAVEPULSER-SI-STUDIO-NRZ + Adaptors and Calibration Kit
WAVEPULSER-40iX-BUNDLE
-
High-speed Interconnect Analyzer, 4-port, S-par @40 GHz, <1 mm Res., 4 phase matched cables, bundle.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-214-HI
Programmable Resistor Module
The 40-230-214-HI (PXI) and 42-230-214-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 470Ω with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Acoustic Calibration Services - IEC
-
Acoustic Calibration Services - IECMake sure you measure correctly! We offer traceable acoustic calibration services according to international IEC and ANSI standards and ensure that your instrument accurately indicates the required measurement parameters. Calibrations are documented, traceable, and digitally signed in cooperation with an accredited calibration laboratory.
-
Product
Modular Low Voltage Motor Protection
LM10
-
The GE Multilin LM10 Low Voltage Motor Protection System is a modular device for low voltage motor protection. The compact design of the LM10 is ideally suited for Low Voltage Motor Control Center applications but can also be used in standalone applications. The LM10 comes standard with the DeviceNet protocol that allows the user to control and monitor the relay over a network. The relay also has an interface port to communicate with the optional LM10 Programmable Display Unit (PDU).
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-351-HI
Programmable Resistor Module
The 40-230-351-HI (PXI) and 42-230-351-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 2.95MΩ with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Calibration Software
-
Calibration software is available to automate all or part of many calibration processes, manage calibration and asset data, and perform other useful tasks as well. Fluke Calibration offers a variety of market leading software applications in each of its product disciplines.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-143-HI
Programmable Resistor Module
The 40-230-143-HI (PXI) and 42-230-143-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 770kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
1 MHz Bandwidth Voltage Preamplifier with Bandpass Filter
EC6081 mk2 - preamplifier
-
The EC6081 mk2 (VP2000) is a 1MHz bandwidth voltage preamplifier with bandpass filter that is designed for uses in conjunction with piezoelectric hydrophones. VP2000 offers excellent low-noise performance over the entire frequency range; and adjustable gain selection. A range of 12 high-pass and 12 low-pass filters are available, these allow ideal band pass filter settings.
-
Product
Voltage Meter
МН4В
-
М-module МН4В is a mezzanine module designed to measure the voltage value of signals through four galvanically isolated channels (four-channel high-speed digitizer).
-
Product
Additional Products: Standard Voltage 50 Pin D-Type Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 11-Channel, 1-Pole
40-321-106-HI
Multiplexer Module
The 40-321-106-HI (PXI) and 42-321-106-HI (PXIe) are quad 11-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
In-plant Low Voltage Wet Sponge
-
Wet Sponge Holiday Detector for Plant or Stationary Operations is highly sensitive and accurate. A uniform coating of only one mil of paint or other non-conductive material over a metal surface is sufficient to repel a small current flow. If a pin-hole holiday is encountered, moisture from the sponge will seep into the hole and create a free path for electrical flow, activating the signal horn.
-
Product
RF Calibration Accessories
-
Employing good connector practice when using an RF calibrator not only avoids measurement errors and minimizes connector repeatability uncertainties but also reduces risk of damage to connectors and equipment. The 96000CONN and 9600CONN connector kits include a range of adapters and torque wrenches intended for use with the 96000 Series RF Reference Sources (9600CONN for the 96040A and 96000CONN for the 96270).The 9600CONN connector kit includes one each of 50 Ω and 75 N-Type male-female adapter for use with the 96000 Series levelling head as a “connector saver” or “sacrificial connector” to avoid risk of damage when making connections to UUT/DUT instruments.
-
Product
PXI High Voltage Power Multiplexer, Hex 4:1 (SP4T)
40-331A-004
Multiplexer Module
The 40-331A-004 hex 4:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
Product
PXI 12xSPST High Voltage Power Relay Module
40-330-003
Relay
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-134-HI
Programmable Resistor Module
The 40-230-134-HI (PXI) and 42-230-134-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 102kΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Calibrated Diffuse Reflectance Standards
-
Diffuse reflection calibration standards in synthetic ODM and ODMP material
