Voltage Calibrators
An accurate voltage units of measure to facilitate comparison to and adjustment of instruments.
See Also: Voltage Sensors
-
Product
Standard Voltage 37 Pin D-Type Cables - Connector to Connector for Pickering
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-030-HI
Programmable Resistor Module
The 40-230-030-HI (PXI) and 42-230-030-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 6.97kΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 5-Channel, 2-Pole
42-321-121-HI
Multiplexer Module
The 40-321-121-HI (PXI) and 42-321-121-HI (PXIe) are quad 5-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
Low Voltage Capacitor Banks
-
Wide range of capacitor banks to correct the power factor in low-voltage electrical installations, for both 50 Hz and 60 Hz networks. Avoid surcharges on the electric bill and improve the capacity of the installation.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels, High Voltage Outputs
M2P.6576-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
PLTS Advanced Calibration
N19305B
-
PLTS N19305B extends the N19301B base product to perform advanced calibration techniques such as Automatic Fixture Removal (AFR)
-
Product
PXI Dual 12:1 High Voltage Power MUX
40-331-002
Multiplexer Module
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
1 MHz Bandwidth Voltage Preamplifier with Bandpass Filter
EC6081 mk2 - preamplifier
-
The EC6081 mk2 (VP2000) is a 1MHz bandwidth voltage preamplifier with bandpass filter that is designed for uses in conjunction with piezoelectric hydrophones. VP2000 offers excellent low-noise performance over the entire frequency range; and adjustable gain selection. A range of 12 high-pass and 12 low-pass filters are available, these allow ideal band pass filter settings.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-113-HI
Programmable Resistor Module
The 40-230-113-HI (PXI) and 42-230-113-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 239Ω with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High Voltage Pultruded Resin Bond Glass Fiber Rod
-
This Test Set-Up can be used to test any kind of Drive Insulator used in Circuit Breaker.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-046-HI
Programmable Resistor Module
The 40-230-046-HI (PXI) and 42-230-046-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 5.806MΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-221-HI
Programmable Resistor Module
The 40-230-221-HI (PXI) and 42-230-221-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 925Ω with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-340-HI
Programmable Resistor Module
The 40-230-340-HI (PXI) and 42-230-340-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 102kΩ with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Barcode Conformance Calibration Standards
-
Barcode symbol quality has been at the forefront of discussion among practitioners in the automatic identification and data capture (AIDC) industry since they were invented in 1951. Barcodes became commercially successful when they were used to automate checkout systems at grocery stores, with the very first scanning of the Universal Product Code (UPC) on a pack of Wrigley Company chewing gum in June 1974. The Uniform Code Council (UCC) published barcode quality guidelines, and ANSI X3.182-1990 became the first published standard for barcode quality. Since then, ISO/IEC 15416 for 1D symbols and ISO/IEC 15415 for 2D symbols have become the global standards for grading printed barcodes.
-
Product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
-
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
Product
6GHz SMA Calibration Kits
CAL-SMA-6F
-
The CAL-SMA-6F Full calibration kit provides all elements for Male and Female Open-Short-Load and Through calibrations for one and two port VNA measurements.
-
Product
High Voltage Waveform Digitizer Family
PXD731x/PXD70xx
-
The PXD731x High Voltage Waveform Digitizer family features up to two 100MS/s simultaneously sampled input channels with 16Bit resolution, input voltages up to ±250V and a bandwidth up to 50MHz. Every digitizer channel has its own 2MB memory which allows up to 1 million samples. Data can be acquired before and after the trigger event with a programmable sample counter, that controls the number of data points. All PXD731x High Voltage Waveform Digitizer family devices have a high common mode rejection ratio (CMRR).
-
Product
PXI/PXIe High Voltage Power Relay Module, 7xSPST With Hardware Interlock
40-323-900-HI
Relay
The 40-323-900 (PXI) and 42-323-900 (PXIe) are 7xSPST relay modules suitable for applications requiring high voltage power switching with high density. They have current handling up to 0.25 A, cold switching up to 9 kVDC/9 kVAC peak and hot switching up to 7.5 kVDC/7.5 kVAC peak.
-
Product
High Voltage Power Capacitors
-
Lifasa - International Capacitors, SA
Capacitors of correction power of cos φ and filtering of harmonics for AT of Lifasa, are manufactured under the base of the container / stainless steel box and porcelain terminals. There are two types, depending on the connection mode that we are going to use:*Single-phase (1 or 2 terminals) with internal fuses, for connection to the network through a double star. Recommended for networks of tension superior to 11 Kv or need of equipment of high power.*Three-phase (3 terminals) with internal fuses, for direct connection to three-phase network. Recommended for voltage networks lower than 11 Kv.
-
Product
Handheld Economic Process Calibrator
VA702
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
This Multifunction calibrator combined voltage. current .resistance .thermocouple temperature .RTD in one device.
-
Product
Battery Voltage Relay
BVR
-
Battery Voltage Relays supply alarm indications at precise voltages for undervoltage and overvoltage conditions. The BVR is designed to prevent damage and incorrect operation during anticipation transient conditions.
-
Product
USB Voltage Measurement Bundle
-
The USB Voltage Measurement Bundle provides a portable, USB-based sensor measurement system that helps you measure input voltage signals while providing isolation and overcurrent protection for high-voltage applications.
-
Product
Calibrating Equipment
-
Stability DC : < 0.01 %FS / 3 min, AC : < 0.02 %FS / 3 minRipple : < 0.2 %Power Supply : 230 VAC, 50 (60) HzPower Consumption : < 250 VAOperating Temperature : 5ºC to 35ºCRelative Humidity : ≤ 80 %Distortion : < 0.5 %Display : 51/2 Digit LED Digital DisplayStep adjustment of Output Signal : 100 %FS / N, 10 %FS / N,%FS / N, 0.1 %FS / N (N = 4, 5, 6, 10 and 15)Dimensions : 190mm (H) x 480mm (W) x 545mm (D)Total Weight : 22.5 kgs (approx.)
-
Product
Calibrators
-
Orbit Controls calibrators are suitable as signal sources for test benches or laboratories. They can be used as generators for calibrating and testing electronic measuring devices or assemblies, both by manufacturers and by companies that must perform periodic calibration tasks for quality certification.
-
Product
Dry Block And Bath Calibrators
-
These units are used to calibrate sensors such as thermistors, thermocouples and RTD's. Different temperature ranges, accuracies and stabilities to cover most sensor specifications.
-
Product
Insulating Boots (Gloves) Withstand Voltage Tester
-
Weshine Electric Manufacturing Co., Ltd
80KV Insulation Boots Withstand Current Leak Testing Withstand Voltage Tester
-
Product
Humidity Calibration Set
-
The humidity transmitters as all other measuring instrumentsshall be periodically checked and eventually adjusted. The most simple solution for this purpose is the E+E calibrationset.
-
-
Product
LXI High Voltage Switching - 6-Bank, 1-Pole, 6:1 Multiplexer Plugin Module
65-231-911
Multiplexer Module
The 65-231-911 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Light / Lux Meter, Calibrated, 50000 lx, 100 lx, 4 %, 185 mm, 78 mm, 38 mm
72-7250 CAL
-
The 72-7250 CAL from Tenma is a digital light meter with RS232 capability. It has custom one-chip microprocessor LSI circuit which ensures high accuracy. The meter features 13mm (0.5”) super large LCD display with contrast adjustment for best viewing angle, data hold and auto power off. It records maximum, minimum and average readings with RECALL facility. The 72-7250 has RS-232 PC serial interface, user selectable lighting type (tungsten, fluorescent, sodium or mercury, daylight) and zero adjustment by push button. The meter operates from 9V battery.
