Filter Results By:
Products
Applications
Manufacturers
Charge Amplifiers
A high-gain voltage amplifier with negative, capacitive feedback for converting a charge into a low impedance output voltage.
-
product
Dual-Mode Charge Amplifiers
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
product
In-Line Charge Amplifiers
The in-line charge amplifier is used to excite structures or machinery with a definable impulse force. Resonances are identified by impulse, an important measurement parameter for the study of dynamic behavior. The 4705A1 is a fast turn on time, 50 mV/pc, in line charge amplifier with BNC jack connectors on each side.
-
product
20-50,000 Hz Charge Amplifier
203G8
The Trig-Tek™ 203G8 accepts pickupswith sensitivities varying from 1 to 110pC/g. It has three simultaneous outputs:Acceleration with a sensitivity of 100 mVrms/Pk g; Velocity with a sensitivity of 534mVrms/Pk/ips; and Displacement with asensitivity of 100 mV/mil DA.
-
product
Miniature
Columbia Research Laboratories
This group is made up of the 6000 and 7000 Series Accelerometers. The 6000 Series offers detachable cables and connector assemblies, a special inverted seismic element for mechanical isolation and other features normally available only on standard size sensors. The 7000 Series are true "shear-mode" design accelerometers which offer performance characteristics and accuracies normally only available with standard size accelerometers. High temperature models of these series are available and will operate to +500°F. For best performance use with Columbia Model 4601 Charge Amplifier or Model 5810 Inline Charge Converter.
-
product
Charge Amplifiers & Signal Conditioning
The use of charge amplifiers alongside piezoelectric charge output sensors is still widespread in many industries. This is due to the rugged and high temperature capabilities of the sensors. There are many challenges in using these sensors and it needs a good understanding of the technology to get a quality, noise free signal for accurate data.
-
product
Charge Amplifier
CH-1200A
CH-1200A is a high-performance charge amplifier to convert charge signal to voltage signal. Built-in integration function allows optimization of the signal which is input to the vibration data analyzer connected.Changing into a multi-channel amplifier is easy by connecting multiple units.
-
product
Signal Conditioning Instrumentation
Columbia Research Laboratories
Columbia offers a wide variety of Signal Conditioning Instrumentation for a variety of Sensor types. These range from Laboratory as well as Airborne Charge Amplifiers, Differential Charge Amplifiers, In-Line Charge Converters, Constant Current Power Supplies and ICP Compliant Amplifiers all in support of Columbia's extensive Piezoelectric product line. Additionally Columbia offers unique Strain Gage Instrumentation Amplifiers which provide built in auto zeroing of gage offset voltages which can increase typical measurement accuracies. These robust Signal Conditioning products have been flight qualified on many current military aircraft and missile programs and are now available for your distinctive program needs.
-
product
Charge Integrator Amplifiers
AD8488
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
product
Digital Charge-input Vibrometer
This is a Digital Charge Amplifier type Vibrometer covering 1Hz 100 kHz Conversion of the Measured value and Change of the Units are all done automatically. Measurement Function are selected by the Soft-touch Keys. It saves the users from complicated operations. Reading indication is easy.
-
product
High Temperature Accelerometer
HA602-A100
Charge Amplifier for use with CM362 High Temperature Accelerometers, Acceleration
-
product
General Purpose
Columbia Research Laboratories
This group of accelerometers is made up of the 3000 and 5000 Series. The 3000 Series are standard size units, including many with all welded construction, that are hermetically sealed for use in dirty and humid environments. The 5000 Series are smaller and lighter in weight than standard units. Characteristics are almost identical except that with miniature units higher natural frequencies and shock levels can be obtained due to their inherently reduced mass. Sensitivities, however are somewhat lower. High Temperature models are available that operate to +500°F. For best performance use with the Columbia Model 4601 Charge Amplifier or Model 5810 Inline Charge Converter.
-
product
High Temperature Accelerometer
HA602-V100
Charge Amplifier for use with CM362 High Temperature Accelerometers, Velocity
-
product
Charge Amplifier
This compact Charge Amplifier has 3 signal routes.When it is used as the Charge Amplifier for the vibration analysis systemWave Stocker, all setups are possibleby the upgraded software.
-
product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
-
product
Charge Amplifier for Outputs from Piezoelectric- or mV-type Accelerometers, Force Gauges, Microphones & Pressure Pickups
Trig-Tek™ 201AP
Amplify the outputs from piezoelectric- or mV-type accelerometers, force gauges, microphones, and pressure pickups
-
product
PXI Voltage Amplifier, +/-33V
41-650-001-S1
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
PXIe Dual Channel 20GHz 30dBm RF Amplifier
3202
Model TE3202 is a dual channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
PCI Bus Signal Amplifier
3322
Model 3322 is a 3U single-slot, PCI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3322 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
product
PXI Signal Amplifier
3180
Model 3180 was designed as a general purpose, wide band and high voltage amplifier, however, with specific applications in mind. It offers selectable gain of up to x50, with amplitudes of -90V to +90V and an output current of 150mA.
-
product
Charge Amplifier
ZET 440
Charge amplifier ZET 440 for piezoelectric detectors is intended for:*amplification and conversion of output signals of primary piezoelectric transducers with charge output;*amplification and conversion of output signals of primary transducers with the IEPE type in-built electronics to voltage;*gain ratios: 1, 10, 100;*LPF: 0.1, 1, 10 Hz
-
product
Signal Amplifier
9400
Model 9400 was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It has four channels built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
Amplifier Operating with High Temperature Accelerometers Where Pyroelectric Effects May be Encountered
Trig-Tek™ 203PC-1/2
Operates with high temperature accelerometers where pyroelectric effects may be encountered, with frequency range from 3 Hz to 40,000Hz
-
product
Synchro Power Amplifiers
SPB
Computer Conversions Corporation
SPB Series: 25VA, 30VA and 100VA Reference Powered Wide-Band 60/400Hz. Models
-
product
Signal Amplifier
9100
Model 9100 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9100 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
product
PXI Voltage Amplifier D Type Connector
41-650-001
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
product
Synchro Power Amplifiers
SSP
Computer Conversions Corporation
The SSP Series are Compact, Reference Powered and Isolated Synchro Power Amplifiers, and AC Sine/Cosine ( Resolver ) to synchro converters; designed for moderate wattage, and re-transmission requirements; providing ultra high efficiency, and ultra high reliability in service, and ease of use. They are ideally suited for demanding Naval/Maritime, Aircraft, and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and active control systems. They are suitable to drive both CT and CDX type passive loads, and virtually any synchro input instrumentation, or control.
-
product
Motion Control Terminal Board for Panasonic MINAS A4 Servo Amplifiers
DIN-814P-A40
This well-designed motion control terminal board is for the users who use Panasonic MINAS A4 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Wideband Amplifier PXI Card
GX1222
The GX1222 is a 3U single-slot, PXI-based wideband power amplifier used for signal amplification purposes. Offering excellent fidelity, the GX1222 amplifies signals from DC to over 20 MHz with a fixed gain of x10. Custom gains are also available without compromising signal purity and amplifier performance.
-
product
Synchro Power Booster Amplifiers
Computer Conversions Corporation
The SPA Series "Pulsating" Synchro Power Amplifiers are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and radar/Antenna related, applications. They are commonly used on synchro based data transmission, re-transmission, simulation and instantaneous absolute position indicating and active control systems.
