Pull Force
strength necessary to extract.
See Also: Force, Compression, Crimp Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
product
Force Sensors
Our force sensors are indicated for use in modal and structural analysis, process control, and general-purpose dynamic force measurements. See our range of charge modes and IEPE force sensors.
-
product
Pull tester for Dade County Protocol PA 105-A
FIXUROOF 300
The Fixuroof portable pull-tester is an accurate unit, designed for testing in the field the pull-out force of base ply fastener. Easily determine whether the mechanical fastener provides sufficient resistance to static uplift force to meet the wind load requirements.
-
product
Force Logger Sensor
NUL-211
This sensor can measure the mass to weightrelationship and study how different pulleysystems affect the effort needed to lift weights.It can also be used to measure push/pull forcesand impacts. There is a hook at the bottom of the force sensor that can be connected to various pulling loads.
-
product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
product
Force Sensor Elements
The STL Force Sensing Tension Links are a series of unique force sensors. The Tension Links utilize the internal strain gage process sucessfully and are used in bolts, load pins and flat load cells. The sensing element consists of a strain gage bridge circuit internally installed in a small hole along the longitudinal axis. This unique arrangement provides a most effective means for the protective sealing of the internal electronics while minimizing the adverse effects of extraneous torsion and bending loads.
-
product
Forced Air Cryogenic Cooling
FixTreme TE
FixTremeTE is a cost-effective standalone alternative to mechanical or forced air cryogenic cooling. When paired with a Testforce dbGuard Series RF shielding test enclosure, performing at temperature RF & microwave functional testing is simple.
-
product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
product
Compact Hydraulic Vibrator Force Simulator
JF Series
The JF Series Force Simulator was developed with the emphasis on light weight, compact size and ease-of-use as a general-purpose, compact jack for the Servopulser system. Testing systems installed with the Force Simulator can easily perform endurance, fatigue and simulation tests on small structural members and various other structural members, which helps improve the logical design and reliability of products.
-
product
Force Gauges
Morehouse Instrument Company Inc.
Minimize user error and achieve higher accuracy with Morehouse Digital Force Gauges. These instruments display the applied force value directly and do not need an interpretation table. Morehouse analog Ring Force Gauges can also be upgraded to the new digital system.
-
product
Pull Through Solutions
Allows pull-through removal of connector modules and instrumentation from chassis backplane.
-
product
Force Measuring Instruments
Force measuring means measuring a certain load in newton, independent of the gravity.
-
product
Forced Air Cooled RF Coaxial Loads
86700 Series
The 86700 Series Forced Air Cooled RF Coaxial Loads are capable of dissipating up to 75 kW of CW RF power from DC Hz to 240 MHz with a VSWR of 1.15:1 or less. With this low reflection coefficient the loads are very useful for tuning transmitters.
-
product
ForceTest Force Measuring Software
AMETEK Sensors, Test & Calibration
The ForceTest software interfaces directly with your digital force gauge enabling you to automatically capture tests and graphs on a personal computer. Test results and graph can be monitored directly on the live screen in real time while the test is being performed.
-
product
Centor Easy R, digital force gauge with external sensor
CNR EAR
The Centor Easy R force gauges are designed to meet the production needs of its users. This group offers several features which are indispensable today for Quality Control, for example: ease of reading with its large backlit graphical display, RS232 output, memory of the last 100 values and ability to set thresholds with visual and sound alarms.
-
product
Twin columns automated force test stand 36" travel - 10,000 lb
710SN
The advanced 710SN Series Universal Test Systems are ball screw driven test stands, excellent for affordable, precision tensile and compression testing of a wide variety of materials, products or ASTM standards. These variable speed testers have increased speed ranges and include adjustable travel limit switches. With the unique dual testing area, users can setup for two tests, tensile and/or compression, without having to switch out fixtures.
-
product
Peel Force Tester
PT-55
V-TEK Peel Force Testers are built to test, confirm, and record proper sealing strength of cover tape to carrier tape. This ensures parts are secure and protected, yet will release at the designated force. The PT-55 Peel Force Tester incorporates new technology and performance features to make set up easy, maintenance minimal, and calibration accurate. The lightweight design can accommodate 8-120mm tape widths and operates at peel speeds of 120mm/min or 300mm/min.
-
product
3-Component Quartz Force Rings And Links
Three-component dynamic force sensors are offered in both ICP® and charge output configurations for dynamic and quasi-static force measurement applications. Each utilizes an array of precision aligned, quartz sensing crystals. Measurements along the z-axis are proportional to applied compression, tension and impact forces. Measurements along the x and y axes are proportional to shear forces that are imposed upon preloaded crystals by the test fixture.
-
product
Twin columns automated force test stand 48" travel - 10,000 lb
710TN
The advanced 710TN Series Universal Test Systems are ball screw driven test stands, excellent for affordable, precision tensile and compression testing of a wide variety of materials, products or ASTM standards. These variable speed testers have increased speed ranges and include adjustable travel limit switches. With the unique dual testing area, users can setup for two tests, tensile and/or compression, without having to switch out fixtures.
-
product
Wideband Active Load Pull Export Control
S94573B
The software enables power amplifier distortion measurements under varying load conditions that are controlled across the entire modulation bandwidth. When design verification and robustness evaluation require testing the device away from the optimum loading condition, this application provides powerful insight into device performance and degradation.
-
product
Force and Material Testing
Starrett Force and Material test solutions range from simple hand-held measurements to highly advanced applications with extreme accuracy.
-
product
Motorized Force Test System
MT Series
In the past, film extruders, paper producers, converters, and woven/non-woven fabric producers have had the choice of test stands and universal test machines which are either value-priced peak-force-only machines, or expensive computer-operated integral-load cell machines. Now you can have the best of both worlds in a single instrument. The series MT-1500, a simple to use computer operated tester, with Quality Control software for automatic calculation and graphical display of break, elongation, yield, modulus, and other, tension and compression force information.
-
product
DIGITAL EXTRACTOR - Roofing and construction pull tester
EXTRACTOR
The DIGITAL EXTRACTOR portable pull-tester is ideal for your quality test of fixing fasteners. It allows you to evaluate easily in the field the tensile pull-out force (commonly called extraction) of your fixing system on various substrate materials.
-
product
Atomic Force Microscope
HDM Series
The task of identifying nanoscale defects is a very time consuming process for engineers working with media and flat substrates. Park NX-HDM is an atomic force microscopy system that speeds up the defect review process by an order of magnitude through automated defect identification, scanning and analysis. Park NX-HDM links directly with a wide range of optical inspection tools, thus significantly increasing the automatic defect review throughput. In addition, Park NX-HDM provides accurate sub-angstrom surface roughness measurements, scan after scan. Park NX-HDM, together with its industry's lowest noise floor, and its unique True Non-Contact™ technology, it is the most accurate AFM for surface roughness measurement in the market.
-
product
Force Tensiometer
K20
Our Force Tensiometer – K20 is a robust, semi-automatic instrument for the precise measurement of surface tension and interfacial tension. Using the ring and plate method as the main tensiometric methods, it produces reliable measurements for the routine quality assurance of your surfactant solutions and interfacial processes.
-
product
Axial Force And Torsion Testing Machine
Evaluation Testing That Approximates Operating Conditions of Materials and Parts - Loading methods similar to actual usage - Allows simultaneous application of axial and torsional loads to samples
-
product
Temperature Forcing System
ETF-SERIES
Precise Temperature Accuracies with Reliable Test Results Temperature Limits: -40/-60 °C to 30 °C Temperature Accuracies: ±2-3°C Temperature Rate of Change: 20-25 deg /min (Non-linear) Maintenance Free Access to The System Self-Sufficient System Compact with small footprints suitable for any space constraint laboratories Low decibel system Suitable for testing electronic chips / devices Environmentally friendly refrigerants Efficient heating Microprocessor based single set point PID temperature controller with data logging Flexible hose up to 2.5-3.0m Interchangeable heads according to chip size. Inbuilt electrical control panel with switchgear system
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type G, Ø1.50mm, 305gf
K100-G150305-SKAU
K100 Series, Pitch 100mil, Tip Style G, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
product
Sensor Products: Weld Force Probe Auditing System
90061-XH Series
This system is ideal for field measurement and data logging of forces between the tips of resistance spot welders. The system consists of a handheld sensor and portable readout/ data logger (PMAC 2000).
-
product
Force Sensor Elements
TE Connectivity (TE) enables OEMs to measure force using MEMS-based technology load cells. The same proprietary piezoresistive silicon strain gage technology used to measure pressure can also be configured into a reliable, low-cost package to measure force.
-
product
Load Cells & Force Transducers
BLH and Nobel Weighing Systems offer a wide variety of load cells and force transducers, ranging from the unique KIS load cell and weigh module to the VPG transducers range of products. Our many years of experience, our state-of-the-art instruments, and the exceptionally broad range of components that go into our systems allow us to deliver high-quality solutions tailored to your needs.
