Filter Results By:
Products
Applications
Manufacturers
Pull Force
strength necessary to extract.
See Also: Force, Compression, Crimp Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
product
Digital Push And Pull Force Gauge
HG-2-1000
Shenzhen Chuangxin Instruments Co., Ltd.
Digital push and pull force gauge is a universal portable force device, testing push and pull load. It is small, light, easy to take, multi-function, high precision. Applicable for all products doing push and pull load test, insert and pull out force test, destroy test, etc. It also can be combined with the machine and clamp to make up a small tester for different purposes.
-
product
Pointer Type Push Pull Force Gauge
NK-20
Shenzhen Chuangxin Instruments Co., Ltd.
*Easy to be operated and can be installed with all kinds of test stands and clamps.*Peak holding function and continuous.*One year free maintenance.*Compact and artistic packing, easy to transit and stock.*Two kind of unit dual show at the same time,*don't need unit conversion. *NK Series: Newton and Kilogram dual unit; *NLB Series: Newton and Pound dual unit; *ALB: Pound and Kilogram dual unit.*Needle indicates, easy to read, high accuracy.
-
product
Manual Test Shell For Push And Pull Force Gauge
HST-S
Shenzhen Chuangxin Instruments Co., Ltd.
HST Manual Test Stand have HST-J and HST-S model, is specially designed to match all kinds of Push Pull Gauge and applied in tension, compression, insertion, withdraw and fracture test.
-
product
Pull tester for security testing
SAFOR 2000
The Safor portable tester is an accurate unit, designed for testing the pulling force of fixings prior to being put into service. Easily prevent accidents by testing on site the fixings to install end brackets and safety harness eyebolts.
-
product
Tensile Compression Force Tester
ESM303
The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMeTM force-based positioning - using your hand as your guide, push and pull on the force gauge or load cell to move the crosshead at a variable rate of speed.
-
product
Adhesion Tester
Surf-2
Rtec Adhesion Tester is a turn key solution to measure Pull up Adhesion force, Work of Adhesion and Shear Adhesion of materials. Equipped with Ultra-Sensitive Capacitance Load Cells this tester provides µN level resolution with forces up to 5N. The High-Resolution sensors allow characterization of large samples over macroscopic length scales to study the effect of texture and other surface modifications. Integrated with High Resolution Inverted Camera, it allows the researchers to measure Contact Area vs. Force making it extremely useful in measuring Adhesion of Soft Materials, Biomimetics and Hydrogels.
-
product
Push Pull Force Gauges
Used in rubber plastic, textiles, waterproof materials, wire and cable, metal materials tensile, compression, bending, cutting and mechanical propertie test, increase the affix to do bending test, it is scientific research institues, universities and colleges,industrial and mining enterprises, the technical supervision and inspeciton arbitration of the department idea test equipment.
-
product
Cord Swiveling Test Set Up For Hair Dryer & Hair Straightner
SCR Elektroniks make CORD SWIVELING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis,20 Revolutions clockwise & 20 Revolutions anti-clockwise.
-
product
Ergonomics Force Gauges
Series E
Series E push / pull force gauges make job task analysis and ergonomics analysis simple and accurate, ideal for workplace design, strength assessment, and ergonomic studies. Series E presents the ergonomist and other professionals with a simple and economical testing solution. 100 lbF, 200 lbF and 500 lbF (500, 2,500, and 5,000 N) capacity force gauges are available, along with a wide range of attachments for various applications.
-
product
Force Gauges
A digital force gauge, often called a push pull force gauge or tension and compression force gauge, is used in material testing, quality control and assurance, research, development, product testing, laboratory and educational applications. PCE Instruments' (PCE) digital force gauge products are the benchmark of quality and performance. PCE digital force gauge devices provide measurements in kilograms (kg), grams (g), ounces (oz), pounds (lbs) and Newtons (N) of force (f), depending on the force gauge model. Most PCE digital force gauge products are handheld, portable devices that also can be used with a universal test stand. There are several different force gauge products available online in the PCE web shop.
-
product
Force gauge kit for tile testing
TILE TESTER
The Tile uplift portable tester is an accurate unit, designed for testing the pulling force of installed roof tiles. Easily perform your quality test with our full equipped Tile tester and prevent from loose tiles.
-
product
Electronic Tensile Strength Tester Pull Force Test Chamber Applicable Industri
Shenzhen Chuangxin Instruments Co., Ltd.
This machine can test various materials (both finished and semi-finished products ) of tensile strength ,compressive strength and elongation ,can do stripping ,tear strength ,flexural ,compression test and etc. It can connect up to the computer and display or printout the test times , test value , max. value , etc . Also it can make various report forms according to the requirements .
-
product
Mechanical Force Gauges
Imada mechanical force gauges are highly accurate instruments used to test the quality, strength or functionality of component parts or products. Imada mechanical force gauges check both compression and tension (push or pull). Peak force can be captured using the peak indicator needle and the tare ring compensates for the weight of attachments. Imada force gauges are constructed with a heavy-duty metal case and all metal components to enable them to retain their calibration for years with proper care. These mechanical force gauges never need charging or batteries and are intrinsically safe in hazardous environments.
-
product
Cord Flexing Test Set Up For Hair Dryer and Hair Straightner
SCR Elektroniks make CORD FLEXING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis, Clockwise & Anti-clockwise. Frequency is 10 turns in one minute.
-
product
Compression Load Cells
A block that is designed to hold a load at one point to measure the compression. While tension load cells measure the pulling force, compression load cells measure a pushing force along a single axis.
-
product
Push Pull Force Gauge Meter
NK-10
Shenzhen Chuangxin Instruments Co., Ltd.
*This push pull force gauge Easy to be operated and can be installed with all kinds of test stands and clamps.*Peak holding function and continuous.*One year free maintenance.*Compact and artistic packing, easy to transit and stock.*Two kind of unit dual show at the same time,*don't need unit conversion. *NK Series: Newton and Kilogram dual unit; *NLB Series: Newton and Pound dual unit; *ALB: Pound and Kilogram dual unit.*Needle indicates, easy to read, high accuracy.
-
product
Wire Crimp Pull Tester (Manual)
WT3-201
The WT3-201 wire crimp pull tester is designed to measure the pull-off force of crimped wire and tube terminations. An ergonomic lever allows for easy application of up to 200 lbF (1,000 N) of crimp pull force. Adjustable wire terminal grip contains multiple slots for wire diameters up to AWG 3 (0.25 in [6.3 mm]). The tester accommodates most insulation types. Samples can be sent to Mark-10 for evaluation prior to purchase.
-
product
Testing Tensile Strength of Overlays, and Overlayments
James Bond Test ™ MK III
The James Pull Off Adhesion/Bond Tester measures the pull force used to pull a 2? or 3? disc away from the material being tested. This pressure is displayed on a precision gauge and can be related directly to the strength of the adhesion to the surface being tested.
-
product
Bench-Top Wire Crimp Pull-Force Tester
PT-1500
PT-1500 Bench-Top Wire Crimp Pull-Force Tester, Manual Lever-operated for 5.84mm 8-30 AWG
-
product
Test Hook Probe
CX-S11
Shenzhen Chuangxin Instruments Co., Ltd.
Test Hook Probe Used on enclosures prior to accessibility testing. The test hook is ¨hooked〃 into vents and seams in the enclosure & then pulled with a force (usually 20N).
-
product
Digital Force Gauge
Guangzhou Amittari Instruments Co.Ltd
The digital force gauge is a kind of simple and convenient multi-functional instrument for high-accuracy push force and pull force test. It is widely used in electronics, building hardware, textile, auto parts, ignition device such as lighter, fire fighting equipment, pen manufacturing, lock manufacturing, fishing gear, chemical, power machinery, scientific research institutions and other industries. For the push and pull load test, plug and unplug force test and destructive test etc.
-
product
Digital Force Gauges
Imada digital force gauges are highly accurate instruments that provide the precise force measurement required in quality testing that determines strength and/or functionality of a part or product. Digital gauges can be used for destructive or non-destructive force measurement applications and check both compression and tension (push or pull) forces. The high sampling rate of Imada digital gauges enables them to capture the peak force of destructive tests which occurs in milliseconds. Imada digital force gauges also feature selectable units: lbf, kgf and N and easy-to-program high/low setpoints for Go/No Go testing.
-
product
Analog force gauge for pull tester
FGC
All our pull tester models come with a quick release gauge so that the gauge can be changed for a different capacity to have the most accurate result. All our gauges are factory calibrated prior to dispatch with a certificate provided.
-
product
Pull Through Solutions
Allows pull-through removal of connector modules and instrumentation from chassis backplane.
-
product
Motorized pull tester
EXT DRV
This battery operated adjustable speed motorized pull tester is used to prove the holding capacity of hundreds of types & sizes of fasteners in roofing, construction, commercial, industrial, and other applications.Specifically engineered for pull-out strength tests and nondestructive testing of welded, staked, threaded, epoxied and power-driven fasteners.
-
product
Load Pull Test Fixtures
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
-
product
Pull Off Adhesion Tester
106
Applications for the Elcometer 106 Adhesion Test include paint or plasma spray on bridge decking, coatings on steel, aluminium, concrete etc.Supplied in a carry case - ideal for site testsHand operated - no need for a power supplyIncludes a cutter for EN13144 and ISO 4624 tests
-
product
Force Sensors
Specially designed for overseeing manufacturing processes. It measures with high consistency the regularity of compression load generated when fitting pieces.
-
product
Force Sensors / Force Transducers
HBM force sensors and force transducers measure static and dynamic tensile and compressive loads - with virtually no displacement. Your force load cell can be supplied in the most varied of designs and classes of accuracy. Typical force measurement application areas include bench testing, e.g. force measurement to check material quality and automation technology, e.g. for monitoring quality during reshaping or bonding operations.
-
product
Force Transmitter
LKVE/i
The PIAB LKVE electronic overload protection system consists of a force transmitter with amplifier and an electronic signal processing unit. The PIAB LKVE force transmitter is attached to a stationary line part. The rope is deflected via a slight angle between the two wheels and the clamping jaw. When loaded, the rope tends to straighten and applies a force which is transmitted to the load cell. The load cell in the PIAB LKVE delivers a signal proportional to the force on the load cell. The signal is amplified and is converted to 4-20mA. This standardized signal (4-20mA) allows distances between the force transmitter and the electronic unit to be 500 m.
