Filter Results By:
Products
Applications
Manufacturers
-
product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
product
Data Acquisition I/O Boards
General Standards Corporation is a leading supplier in data acquisition I/O boards, provides a complete family of data acquisition cards for sonar, industrial, and embedded applications on several form factors/busses, and for many operating systems. Functions available include analog I/O, serial I/O, and high speed parallel I/O.
-
product
VME Form Factor Extender, 6U, 180mm
111FFE6018-012X
The VME form factor extender 6U 180 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
product
Advanced 4-Axis Servo & Stepper Motion Controller With Modular Design
PCIe-8154
The PCIe-8154 delivers high-frequency pulse rates up to 6.55 MHz and hardware-controlled emergency stop, software security protection, card index switching, and simultaneous linear/ circular run, exceeding industrial cost/performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and any pulse-train controlled servo and stepper drives, the PCIe-8154 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous contouring. Applicable for a variety of linear and circular trajectories, the PCIe-8154 delivers the smoothest motion control for a wide range of manufacturing applications. Modularized configuration accommodates ADLINK extension boards for distributed I/O control and high-speed triggering functions.
-
-
product
VME PowerPC Single Board Computer
DP-VME-0405
The DP-VME-0405 is a high performance VME PowerPC single board computer(SBC) that features the latest PowerPC 7410, SDRAM with error detection and correction and a dedicated L2 cache bus. The board's architecture strikes a balance between high performance processing power, memory and I/O resources. With its vast array of interfaces, the DP-VME-0405 allows the user to perform intensive I/O while permitting rigorous computing. Two industry standard PMC slots enhance the I/O capability, allowing the users to provide program specific features by using commercially available PMC module.
-
product
4 Channel 500 MS/s 12-bit ADC/Digitizer
SIS3350
4 channel 6U VME digitizer/transient recorder with a sampling rate of up to 500 MS/s (for the individual channel) and 12-bit resolution. The board has a width of one VME slot (4TE). The boards multi event and readout in parallel to acquisition functionality make the card the choice for many demanding digitizer applications.
-
product
3U CPCI I/O & Comm Board
3U cPCI 75C5
NAI’s 75C5 is a 3U cPCI Multifunction I/O and Communication Board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed Analog-to-Digital (A/D) channels and 28 Discrete I/O programmable channels, or with a reference power supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
COM Express® Type 7 Reference Carrier Board in ATX Form Factor
Express-BASE7
The Express-BASE7 is an ATX size COM Express Type 7 reference carrier board. Together with the COM Express Type 7 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
System Level Test and Burn-in Solutions
System Level Test (SLT) is a paradigm shift from traditional structural and functional testing. The device is tested in a complete, integrated system to evaluate its compliance against specified requirements. The system approach allows for higher and more cost-effective test coverage especially for multi-function and non-deterministic devices. It also brings new integration and test challenges like: ..Designing test fixtures on Burn-in Boards with system components ...
-
product
Clamp type AC Current Sensor／with DC Voltage Output
ACT-5H
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For current measurements of the control board*AC 0.1A～5A*DC 5V full scale output
-
product
Power Interface and Prototype PXI Card
GX7404
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
product
VITA 48.4 Liquid Flow-Through (LFT) ATR Platform
VITA 48.4 LFT ATR
Elma Electronic’s rugged OpenVPX ATR platform is designed to accommodate boards requiring liquid flow-through (LFT) cooling per the VITA 48.4 standard. VITA 48.4 modules are cooled by liquid flowing through an integral heatsink.
-
product
PCI to PMC Adapter/Carrier
PCIBPMC
1/2 Length Bridge Based PCI Adapter Carrier Card with PMC Mounting Slot. The PCIBPMC ( PCI Bridge PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI slot. The PCIBPMC has a PMC card slot mounted to a universal 1/2 length PCI card. Suitable for 32 bit or 64 bit bus operation. The PMC user IO connector Pn4 is brought out to one of two connectors for access (DIN IDC or SCSI II). The signals corresponding to the PrPMC standard Ethernet and Serial lines can optionally be connected to the Ehternet and Serial port connectors at the top edge of the board.
-
product
Sensor Signal Conditioning System
SCS
SCS Sensor Signal-Conditioning System complements the iDSC 1816 anti-aliasing board to provide a continuous path in a single package: starting with raw measurements at the sensor and ending with conditioned anti-aliased data logged to disk on a PC.
-
product
Air
General Dynamics Global Imaging Technologies
Air superiority calls for highly-trained and experienced pilots, equipped with the very best technology. From high assurance mission computers to on board weapons systems, sensor processing to trusted communications, we deliver the absolute latest in secure avionics.
-
product
Vibration Fixtures From TetraTek's VibraTek Division
HALT And HASS Testing
Our VibraTek TM Division manufactures precision machined, magnesium, and aluminum vibration fixtures with stainless steel and aluminum hardware. These fixtures feature TetraTek developed clamps, retainers, connectors, circuit boards, and cable sets to provide you with the ideal testing arrangement for your products while they are tested for HALT (Highly Accelerated Life Testing) and HASS (Highly Accelerated Stress Screening) response.
-
product
Quad Serial FPDP Interface with Virtex-6 FPGA - PCIe
Model 7811
Model 7811 is a member of the Cobalt® family of high performance XMC modules based on the Xilinx Virtex-6 FPGA. A multichannel, gigabit serial interface, it is idealfor interfacing to Serial FPDP data converter boards or as a chassis-to-chassis data link. The 7811 is fully compatible with the VITA 17.1 Serial FPDP specification. Its built-in data transfer features make it a complete turnkey solution. For users who require application-specific functions, the 7811 serves as a flexible platform for developing and deploying custom FPGA processing IP.
-
product
RF Connectors
HD-EFI Connectors
The HD-EFI product series is a micro-miniature interface designed to allow large board tolerance stack ups, blind mating, and multiple RF lines. It is available in common PCB jack and cable plug configurations, with an assortment of bullet adapters to accommodate many board to board spacing options.
-
product
Laser Head Cable, 3 m
10881D
Provide reliable power with this spade lug that connects the laser head to multiple laser boards.
-
product
Board
Arduino Mega 2560 Rev3
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila.
-
product
Multi-Protocol Board
EXC-4000VME/VXI
The board supports up to 8 modules, and each module represents an independent test and simulation device. Most modules are based on existing Excalibur products such as the 1553 Px family, the 1553 MCH family and the ARINC-429 RxTx. Additional modules are being added constantly.
-
product
Thunderbolt V-600 Board 8-Slot
The 6U VME Thunderbolt boards provide optimal performance and reliability. The Thunderbolt V-600, configured with one Compute Module of four MPC7410 processors, provides 16 GFLOPS of computational performance per 6U VME slot. Data is transferred throughout the Thunderbolt over the SKYchannel Packet Bus. Data moves transparently through the SKYchannel P2 interface to other boards in a SKYchannel chassis.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 2 Channels
M2P.5911-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels
-
product
PCIe Oscar Express 16-Bit Digitizer
The GaGe Oscar Express 44XX CompuScope PCIe digitizer board features 16-bit resolution with sampling rates up to 100 MS/s with true Effective Number of Bits (ENOB) of 12.2-bits with 10 MHz input.
-
product
Carrier Boards
Advantech Development boards provide a schematic software & reference design to reduce efforts needed in development stage. Advantech Development Board can be used to test carrier board problems and support COM series, and Qseven, ETX / XTX form factors.
-
product
16-CH Discrete Input 16-CH Discrete Output Daughter Board Module
HSL-DI16DO16-DB-NN
- Slave ID consumption: 1 16-CH NPN sinking type sensor inputs or dry contact and 16-CH - NPN sinking type outputs- Photo couple isolation voltage: 2500Vrms- Input impedance: 4.7KΩ- Input current: ??10mA(Max), ??12.5mA(Peak)- Input voltage: ??40V (Max)- Output switching capacity:300mA/ch at 24VDC- Terminal Base:HSL-TB64 or HSL-TB32-DIN- LED indicator: Power, Link and I/O status
-
product
Single Rear Slot Universal ISA plug-in PCMCIA Adapter
J105
* High reliability 68 pin PCMCIA compliant,* static protected, connectors with card eject buttons are used.* Standard Types I, II and III cards,* 5V cards supported.* Operating temperature range: 0-50 C* ISA board dimensions: 150 x 100 x 24mm Host Computer:* Any true compatible Pentium PC or higher with ISA Bus.
-
product
Preconditioning
Preconditioning is performed prior to package level reliability testing to simulate the effects of board assembly on non-hermetic devices where moisture may have been absorbed during normal storage. The subsequent exposure to high temperature during infra reflow assembly can cause internal damage such as “pop corning” and delamination.
