Filter Results By:
Products
Applications
Manufacturers
-
product
3200W to 4080W -Single Output - 3200W To 4080W - Single Output
TPS Series
*400/440/480 VAC (Nom.) 3Ph Delta or Wye*Fully Regulated, Wide Range Adj. Output*Voltage and Current Programming*-40°C (start up) to +70°C operation*>92% Efficiency*PMBus™ Communication*Built-in ORing FET for parallel operation
-
product
Low Cost Splitter Systems
RATCAT Family
The CAT Snake Stage Box allows four lines of balanced analog audio to be run down a shielded CAT5/6/7 cable. Each of its four channels can carry balanced analog, AES/EBU, DMX, and Clear-Com signals hundreds of feet away. The CAT Snake is a fully passive unit which can be input directly into analog or digital consoles. Each channel is isolated which means channel 1 can send a DMX Signal while channel 2 is sending balanced analog all down the same shielded CAT5 cable. Multiple CAT Snake stage boxes can be daisy chained to allow the same four analog channels to be dropped in multiple locations. Each CAT Snake stage box has an Ethercon input and Ethercon parallel output that allows the CAT Snake to be used as a hard-wire split.
-
-
product
Data Acquisition (DAQ) And Real-time Control Systems
Our data acquisition devices are capable of storing hundreds of analog and digital channels at full speed while allowing in parallel data to be sent out in real-time to any 3rd party EtherCAT master controller. We have brought the worlds of data acquisition and real-time control closer together which will save you time and money in a big way.
-
product
FLIM Upgrades for Zeiss LSM
710 / 780 / 880
*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Two HPM-100-40 GaAsP Hybrid Detectors*Optional: HPM-100-06 Hybrid Detectors, IRF Width < 20 ps FWHM*Optional: HPM-100-50 Hybrid Detectors for NIR FLIM*Optional: Multi-Wavelength FLIM*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Simultaneous FLIM/PLIM*Detection Wavelength Range from 360 nm to 900 nm*Excitation by Ti:Sa Laser, OPO, or by bh ps Diode Lasers*Identical Systems for Multiphoton FLIM and Confocal FLIM*Detectors can be Swapped Between NDD Port and Confocal Port*Systems are Modular: More FLIM Channels can be Added
-
product
Hot Swap, Fault Tolerant, Ultra Reliable Power Supply
Series HSP
The Kepco HSP series provides mission critical power. HSP comprises a group of twelve models, eight 1000 watt power supplies with outputs from 3.3 volts to 125 volts and four 1500 watt power supplies with outputs from 24 volts to 125 volts. All models feature current-sharing for parallel redundant N+1 operation. Models with the or-ing diode, option R, are capable of hot swapping when plugged into Kepco¹s RA 60 series rack adapter. Models with a digital meter, option M, are also available (see photo, right). A mechanical keying scheme allows the user to define which power supply will plug into a specified slot in the housing. Output voltage and current limit settings are adjustable from the panel and may be remotely adjusted.
-
product
Exchangeable Test Fixture
2112/D/H/S-7/HG/Pylon
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 13,50 kg
-
product
Digital Auto Multi-Meter
This Digital Auto Multi-Meter (DAMM) was designed solely for Automotive Technicians for troubleshooting all electrical problems encountered in the vehicle. Be it a 6V, 12V or 24V system it can be used to check Amps draw directly on the fuse (Mini, ATC or Maxi Fuses) without having to remove it and measure parasitic drain current using the parallel method at the fuse box.
-
product
Analog/Linear Tester
Amoeba 4200
4200 is capable of running multiple test sites independently with a parallel efficiency of up to 85% for quad-site and octal-site testing.It comes with test development and production software suite, which makes the transition from test development and bench characterization to production seamlessly.
-
product
Stand-Alone Test Fixture
MA 2012/D/H/GR2270/71
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,00 kg
-
product
DC Power Supply
◎PW-4063R
*Use Toroidal Transformer. Low EMI & High EMS.*Triple output, 0-32V/0-6A X2 and 5V/3A .Max. 400Watts*Tracking operation. Max. output 64V/6A on tracking series or 32V/12A on tracking parallel.*4 display, Green LED shows Voltage and Red LRD shows Current. Easy to read.*Compact design. G.W. 9Kgs only. Easy to handle.*The resolution of PW-4063R as high as 0.01v and 0.001A.*Provide 4Pcs 10turns micro adjust VR for Voltage and Current adjustment. Easy to operate.*Very low Ripple & Noise, less than 0.4mVrms. Very suit for precise measurement.
-
product
1MP OV10633 Custom Lens Camera Module
e-CAM1M_CU10630_MOD
e-CAM1M_CU10630_MOD is a High Dynamic Range (HDR), Wide Dynamic Range (WDR), custom lens camera module targeted for surveillance and security applications. This HDR camera module based on the OV10633 sensor from OmniVision is e-con’s first Wide Dynamic Range (WDR) camera module that can stream 1280x720p video at 30fps over its 8-bit digital video parallel interface. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice.
-
product
DC Power Supply
CSP-3
Chuan Sheng Electronics Co., Ltd.
● Universal power AC90~264V/DC127~380V● Build in power factor control circuit in high power model(120W~500W)● Available for series and parallel operation● To be a Back up power function with relay output in option( not available in model 20W and 24W)● RoHS & UL version in option● DIN rail mounting
-
product
Audio Analyzer
FLEXUS FX100
The FX100 is a unique professional audio analyzer that adapts to your application. The instrument offers comprehensive measurements including Passed/Failed tests in under 1 second. You may customize the system for two or four parallel channel operation, speaker impedance testing and digital audio measurements. Switcher modules provide additional outputs and inputs.
-
product
Exchangeable Test Fixture
MA 2111/D/H/S-5/HG
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 10,70 kg
-
product
Interface
RCNIC-A2PAU4
Abaco Systems' RCNIC-A2PAU4 is a high performance 4-lane PCI Express interface for monitoring, generating or analyzing full-bandwidth AFDX/ARINC 664 protocol traffic. Our exclusive pipeline architecture maximizes packet throughput using parallel controllers and efficient DMA transfers, thereby avoiding the bottlenecks of CPU-based interface solutions.
-
product
Battery Capacity Testers|Discharge Testers
DV Power offers a wide range of battery capacity testers to meet specific customer needs. All of them are portable, powerful and most of all universal. Any battery string, such as lead-acid, lithium-ion, nickel-cadmium based and others, with voltages in the range of 0,9 – 800 V DC can be tested in an accurate, user-friendly way.The capacity test is carried out following the battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU battery testers enable setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, several units can be connected in parallel, or BXL additional load units can be used. Discharge parameters can be monitored in real-time during the capacity test. Overall battery voltage, current, elapsed test time and capacity will be presented during the entire test on a touch screen display.
-
product
Linear regulated power supply with thyristor pre-regulation
NTN
High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units
-
product
Hyperspectral Cameras with USB3 Vision
xiSpec
*Smallest Hyperspectral camera - Compact, lightweight with only 26.4 x 26.4 x 31 mm, 32 grams (1)*Cost efficient - Excellent value and price through utilizing new imec hyperspectral imaging technology*Cool economy - Low power consumption with 1.6 Watt, minimal heat dissipation, ideal for UAV / UAS*All-around support - USB 3.0 support for Windows 7 and 10, macOS, Linux, ARM*Powerful potential - Highest spatial and spectral resolution, possible with 5Gb/s interface*Optimized - 2048 parallel, "on-chip" integrated spectroscopes with 100 points of spectral resolution each*AIA standard - USB3 Vision standard compliant*Industry standard interface - Compatible with USB 3.0 SuperSpeed specification*Fastest Hyperspectral camera - High speed, high frame rate: based on 170 fps at 2.2 Mpix resolution*Connectivity and Synchronization - Programmable optoisolated input and output, 3 status LEDs*Easy deployment - Range of accessories and wide hardware and software integration*Highly Customizable - Variety of sensor options, which can be further adjusted to match requirements*Interoperability increase - Continuous embrace of new software and hardware partners
-
product
PMC-BiFIFO
The parallel Input and Output channels are highly programmable and fully independent. The standard interface offers Data, Clock and Strobe. The 32 RS485 channels are programmable as input or output allowing for a variety of implementations. The programmable output rates and RS422/485 compatability will interface to a multitude of systems.
-
product
LCR Meter, Hand Held, 100 kHz, 2 kH, 20000 µF, 0.2 Gohm
72-10465
The 72-10465 from Tenma is a LCR meter in orange and grey colour. It features an easy to read dual LCD (40mm x 63mm) display measurement of 19999/1999 (main/auxiliary). It also has series and parallel measurement modes which can be used to select quality factor, loss factor, phase location angle and equivalent resistance of measure articles. Intelligent detection and five different test frequencies enable accurate readings for all sizes of capacitors and inductors. The user can also access the stored data on a PC with the included USB connection and interface software. The compact size and case make this unit far more portable than a benchtop meter.
-
product
VITA 57.4 FMC+ HSPC Loopback Card
Samtec's VITA 57.4 FMC+ HSPC Loopback Card provides FPGA designers an easy to use loopback option for testing low-speed and high-speed multi-gigabit transceivers on any FPGA development board or FPGA carrier card. It can run system data or BER testing on all channels in parallel. This makes evaluation and development with an FPGA much easier and is an ideal substitute for 28 Gbps test equipment.
-
product
COMINT Monitoring System
A modern COMINT system can handle thousands of parallel signals. With a reliable and intuitive management software, the increased situational awareness creates a firm base for any decision making
-
product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
product
Frequency and Phase Agile 120 MHz Signal Generator.
DDS8p
The DDS8p generates cosine, sine and ACMOS/TTL output signals. The frequency is programmable in 1µHz steps from 100Hz to 120MHz. The phase is 14-bit programmable. The DDS8p is controlled by a binary parallel interface that allows frequency and phase changes as fast as 600 nanoseconds. It is accurate to 1ppm and requires 5 VDC power.
-
product
Power Supply, 100V, 33A, 3300W
N8739A
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight N8739A is a 100V, 33A, 3300W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
-
product
2-Slot BRIC, 256x4, 1Pole, PXI Matrix (2 Sub-cards)
40-559-201-256x4
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays. With their high level of switching density, these PXI matrices allow a complete Functional ATE system to be housed in a single 3U PXI chassis and allow the use of much lower cost 8 or 14-slot chassis. The 40-559 matrices can be used in many industries; typical applications include automotive ECU and semiconductor package testing. Dual analog busing for the narrower matrix options, enable completely separate matrices within a single module for parallel testing.
-
product
Exchangeable Test Fixture
MA 2109/D/H/S-5
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 8,50 kg
-
product
Parallel Plate Dielectric Test Cell
LT-4203A
The LT-4203A Parallel Plate Dielectric Test Cell is designed for measuring the AC loss characteristics and permittivity of solid laminates and panels per ASTM Standard D150‑98, and implements the guarded electrode (three terminal) measurement preferred as the referee method.
-
product
CSvideo | CTvideo | CSvision Series Infrared Thermometer
The video pyrometer series optris CSvideo/CTvideo and the new innovative ratio pyrometer CSvision allow a parallel use of video and crosshair laser aiming for an optimal measuring field adjustment even in processes with limited access. They reliably measure temperatures of metals or ceramics and, due to their short measuring wavelength, reduces measuring errors of surfaces with low or unknown emissivities. The high quality video sighting can show its full advantage together with the software CompactPlus Connect or the IRmobile App on your cell phone with state-of-the-art zoom and image rotation features. The adjustable focus, motorized on CSvision, allows an optimal adaptation to different application and installation demands. As CSvision can measure objects up to 3000 °C a unique two-step brightness reduction filter (BRF) is giving the user a tremendous advantage when aiming on hot and extremely bright objects.
