Filter Results By:
Products
Applications
Manufacturers
Receivers
Equipment that is the sink or terminator of any signal on a transmission medium. (atis.org)
See Also: ITA
-
product
Coax, Module, Receiver, 20/26 GHz/75 Ohm HD, 90 Series, 32 Position, incl. strain relief
510104289
Primary mating module 510108179.
-
product
Receiver, G2, 2 Module, Keying Feature, With Protective Cover, With Micro Switch
310120112
Receiver, G2, 2 Module, Keying Feature, with Protective Cover, with Micro Switch
-
product
Cable Assembly, Receiver, 72", TriPaddle, 50 Pin FML DSub
540111030503
Cable Assembly, Receiver, 72", TriPaddle, 50 Pin FML DSub.
-
product
40Gb/s DPSK Receivers
Targeting for the next-generation 40Gb/s system based on advanced optical differential phase shift keying (DPSK) demodulation, Optoplex’s 40Gb/s Integrated DPSK Receiver (DPSK Rx) demodulates an incoming DPSK optical signal into a pair of differentially (amplitude) modulated RF outputs at data rate up to 43Gb/s in a compact package. Phase modulated optical signals offer much better dispersion performance compared with traditional amplitude modulated counterparts because the carrier light stays on all the time so that the intensity-dependent nonlinear effects in the transmission link are avoided, resulting in longer transmission distances.
-
product
PCI Express Receiver Board
AD12-2000-IRIGB
The AD12-2000-IRIGB is a high performance wideband 0.3-1.8GHz PCIe-bus receiver on a single PCIe Gen3 board, that can continuously digitize a wide portion of the RF spectrum, with a 3.6GSPS 12-bit A/D that can be synchronized with stability of better than +/- 100 picoseconds with respect to an IRIG-B 1PPS signal and global time codes from a satellite receiver or local site time reference. Designed for demanding military, scientific, industrial, communications, safety and electrical power utility applications, the AD12-2000-IRIGB has 60dB of gain adjust range (manual and AGC with programmable loop bandwidth), a wideband noise figure of 9dB, +11dBm 1dB compression point, and 2dB peak-to-peak ripple over the 300MHz to 1.6GB frequency spectrum.
-
product
Cable Assembly, Receiver, 36", TriPaddle, 68 Pin ML VHDCI
540120030201
Cable Assembly, Receiver, 36", TriPaddle, 68 Pin ML VHDCI.
-
-
product
Monitor SDR Boards
Multiple Access Communications Ltd.
MAC Ltd’s MONITOR product family includes a number of software-configurable digital signal processing platforms intended for use in radio frequency (RF) receiver and transceiver applications. The MONITOR products are available in assembled printed circuit board (PCB) form for integration into larger systems. They also form the basis of MAC Ltd’s CatchAll™ radio products. In addition to the standard products listed below, MAC Ltd is happy to discuss the customisation of existing products and/or the development of new bespoke hardware and software.
-
product
Speaker Consulting
From 1993 Peter Larsen has worked as an independent consultant for leading loudspeaker factories all over the world. During his career the Ringradiator, a new Racetrack woofer and a 15mm Mobile receiver have been developed among several hundred other transducers. Complete High End enclosure systems and Monitors are among the latest additions.
-
product
Aluminum Portable Telemetry System with Integrated Keyboard and Display
LS-84-AP
The Lumistar LS-84-AP Rugged Aluminum Portable Data Unit offers a low cost, high performance COTS solution for aportable quick look ground station. Lumistar LS-25 FMReceivers or LS-25-D2 Down Converters with LS-35-R Multimode IF Receiver, Bit Synchronizers and Multi-function PCM Decommutators, and LS-71D/A Converters can be installed inthis rugged high quality portable computer and bundled with theLumistar setup, control, and monitoring software to achieve anaffordable alternative to the often expensive, proprietary architecture products of other suppliers. The flexible design allows the user to define the desired data acquisition cardconfiguration to unique requirements.
-
product
Single-Ended to Differential Amplifiers
Analog Devices has developed a broad portfolio of single-ended to differential amplifiers that help designers meet their high performance requirements. ADI single-ended to differential amplifiers enable the processing of both single-ended inputs to complementary differential outputs or differential inputs to differential outputs. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single-ended output.
-
product
Coax, Patchcord, Receiver, 36", Mini Coax, RG178 Tan, Single Ended
7-334178000-036
Coax, Patchcord, Receiver, 36", Mini Coax, RG178 Tan, Single Ended.
-
product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110177
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Receiver, I2 Micro ICon, 120/12 Position Hybrid, Loaded With Twin Female Contacts (610 138 200)
310130104
The i2 Micro iCon receiver is a one piece connector capable of holding up to 120 Signal QuadraPaddle contacts and 12 Micro Coax or Micro Power. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is pre-loaded with twin female contacts, QuadraPaddle Part # 610 138 200. Accessories such as keying pin kits, protective covers, and strain relief are available.
-
product
Servo Tester
105
Simulates a receiver so you can test your motors and servos without having to use a transmitter and receiver. It can send RC-PWM signal of 1ms to 2 ms in 20ms period. It connects to an ESC via three wires. The servo tester is powered by the BEC in your speed control or by a std 4 cell 5 volt receiver battery
-
product
Cable Assembly, Receiver, QuadraPaddle, 20"
540219010134
Cable Assembly, Receiver, QuadraPaddle, 20"
-
product
Coax, Patchcord, Receiver, 36", Mini Coax, RG178B MCX PL
7-364178604-036
Coax, Patchcord, Receiver, 36", Mini Coax, RG178B MCX PL.
-
product
Micro Coax, Module, Receiver, iCon, 40 Pos, Fully Loaded
510160129
Micro Coax, Module, Receiver, iCon, 40 Pos, Fully Loaded.
-
product
Receivers
Series 32
Semco’s Series 32 Receivers are the optimal design for interfacing the GR 2270 style (VG) test fixtures. Featuring Semco’s patented CAM/TRAC® design, the Series 32 Receivers provide a locking system that assures consistent contact throughout the entire interface. With a full 5/8″ stroke, the Series 32 Receivers allow additional clearance for coax and custom block applications. They are available with or without vacuum ports. Models include: Bench Top, Slope, 19” Rack Mount, Dual 19 Rack Mount, and Dual Benchtop configurations.
-
product
Amplifier Built-in Ultra-compact Laser Sensor
EX-L200
Panasonic Industrial Devices Sales Company of America
The EX-L200, the one of the world’s smallest Laser Sensors with a built-in amplifier, is designed to detect minute objects with utmost accuracy. Despite its miniature size, the Thru-Beam Type (EX-L211) can detect minute objects with a diameter of just 0.3mm, and the Spot Reflective Type (EX-L221) can even detect gold wire whose diameter is a mere 0.01mm. To facilitate solving application tasks, these sensors come equipped with a Potentiometer and two indicator LEDs. For the Thru-Beam Type, reflective material on the receiver allows users to visualize the laser beam, easing beam-axis alignment.
-
product
Mini Coax, Contact, Receiver, Solder Sleeve, RG316 & RG178
610104142
Mini Coax, Contact, Receiver, Solder Sleeve, RG316 & RG178.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 30µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Solder SleeveInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 2 GHzVSWR ≤ 1.2 @ 2 GhzInsertion Loss ≤ 0.05 dB @ 500 Mhz≥ -0.3 dB @ 2 GhzDWV 1500 VDC Min.Contact Resistance ≤ 5 mΩCable Specifications RG316 & RG178Environmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
product
Receiver, G12, 12 Module, 15" Platform, for Slide Mount
310104325-1
Receiver, G12, 12 Module, 15" Platform, for Slide Mount (slide kit required)**Please note - This part number ships with the platform not attached to the receiver. Platform must be assembled after delivery. The 15" G12 Receiver is a slide-mounted receiver. The 15" platform provides a surface to hold fixtures or other tools and supports up to 180 lbs. The 15" platform configuration is not compatible with the optional leg kit.This part number includes: G12 Receiver 15" Platform Mounting brackets (for attaching slide kit to platform) Left side microswitchSlide kit, keying kit, instrument bracket, right side microswitch, and any other accessories must be purchased separately. Designed for VPC 90-Series modules.
-
product
Pneumatic, Module, Receiver, 5 Position (3/8" ID)
510104160
Pneumatic, Module, Receiver, 5 Position (3/8" ID)
-
product
Mini Pneumatic, Contact, Receiver, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coaxial/ Mini Power modules
610131108
Mini Pneumatic, Contact, Receiver, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coaxial/ Mini Power modules.
-
product
TDRSS
L3 Cincinnati Electronics (L3 CE) continues to broaden its offering of TDRSS-compatible receivers and transmitters. Virtually any TDRSS forward or return service can be utilized with the following products. All TDRSS products have been live-link tested with the TDRSS constellation to insure compatibility.
-
product
Backshell, I1, Receiver, With Large Clamp Kit
310113727
The receiver backshell is used with the i1 Receiver. It is not mounted to a rack or panel. The backshell provides protection for exposed wiring and is ideal for use with the i1 Receiver and ITA when used in a cable-to-cable application.
-
product
FTTH Bi-Direction Optical Recevier (HFC)
H9925
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H9925 is a type of bi-directional optical receiver with high performance, low cost and economical. It is applicable to various application of the HFC network fiber to the home (FTTH), and can provide high reliability analogue, digital video frequency and data bi-directional transmission for the HFC network.
-
product
CAT-5 Video Receivers
Analog Devices high speed, differential CAT-5 video receivers and equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths. Our video receivers provide excellent common-mode rejection that enables the use of low cost, unshielded twisted pair cables in noisy environments.
-
product
Cable Assembly, Receiver, Mini Power/TriPaddle, 20", 9-Pin DIN and 4 Banana Plugs
540039010111
Cable Assembly, Receiver, Mini Power/TriPaddle, 20", 9-Pin DIN and 4 Banana Plugs
-
product
Noise & Interference Generator
GPS7500
The programmable GPS7500 Noise & Interference Generator is capable of generating up to a 40 MHz wide noise or interference band for GPS receiver susceptibility testing.
