Filter Results By:
Products
Applications
Manufacturers
-
product
Concrete Comprission Testing Machine
CONCRETO 2000X/3000X
CONCRETO Series This compression testing machine can safely and efficiently perform tests at a high capacity without causing explosive fracture (failure of the specimen) on ultra-high-strength concrete, which is used as a structural material in high-rise buildings, etc. This one machine can be used for materials ranging from ultra-highstrength concrete to specimens that have been recently cast, mortar, etc.
-
product
EtherCAT Chassis with EtherCAT Bus-Coupler
EPS-9905 with EPS-6000
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
product
Temperature Controlled Microscope Stage
Linkham Scientific Instruments
Specialists in temperature controlled microscopy, Linkam Scientific Instruments, announce the launch of their Optical DSC450 which enables simultaneous visualization of thermal processes for improved materials characterisation. The Optical DSC450 enables the user to measure glass transitions and melting behaviour of a wide range of substances whilst accurately controlling temperature from -196 °C to 450 °C. The atmosphere of the stage can also be purged with gas as required by the user. A new feature which will increase the characterisation capabilities of the DSC system is to combine it with imaging capability. The new LINK Digital Imaging module enables additional information to be obtained by correlating optical changes such as colour with temperature. The new TASC analysis tool takes this further. TASC (Thermal Analysis by Surface Characterisation) is a new image analysis capability which enables structural changes in samples to be tracked and quantified optically. It has the unique ability to measure local transition temperatures allowing different points on a sample to be identified. The new DSC system is great tool to use in research and quality control to measure quantitative values for glass transitions, melting peaks and sample purity and, when combined with TASC, even sample homogeneity.
-
product
Simulation and Testing Solutions
LMS
Siemens Digital Industries Software
LMS simulation and testing solutions help manufacturing companies manage the complexities of tomorrow’s product development by incorporating model-based mechatronic simulation and advanced testing solutions in the product development process. Our products and services tune into mission-critical engineering attributes – ranging from system dynamics, structural integrity and sound quality to durability, safety and power consumption.
-
product
Aerospace Testing Solutions
Aerospace Testing SolutionsDewesoft offers a variety of solutions for aerospace testing. From standard data recording, structural dynamics, rotating machinery analysis, acoustic testing, to more specific applications like ground station telemetry solutions with full support for ARINC-429 and MIL-STD-1553 buses, PCM telemetry, IRIG 106 - Chapter 10, Ethernet packets, and iNet telemetry.We can provide flexible and robust data acquisition hardware and software that will match your requirement for testing airplanes, helicopters, rockets, satellites in the air, space, or on the ground - proving ground, wind tunnel, vibration shaker or acoustic chamber. Our solutions are being used and trusted by leading aerospace companies on the most demanding projects like NASA, ESA, Space X, Airbus, Boeing, Lockheed Martin, Bombardier, Honeywell to name just a few.
-
product
Solar Radiation (Sunshine) Test
This test determines the effects of direct solar radiation on components and material. The heating effects of solar radiation differ from those of high air temperature in that the amount of heat absorbed depends on the roughness and color of the surface on which the radiation is incident and the angle of incidence to the sun. Variations in the intensity of solar radiation over the surface of the component, may cause components to expand or contract at different rates, which can lead to severe stresses and loss of structural integrity. In addition, degradation due to photo-chemical changes can occur such as fading of color, deterioration of natural and synthetic elastomers and polymers. The test items that are subjected to solar radiation testing are those that are exposed to solar radiation during its life cycle, in the open, in warm climates.
-
product
Bridge Monitoring
Structural Health Monitoring of BridgesDewesoft data acquisition systems are used in structural health and seismic bridge monitoring projects ranging from structural mechanics to continuous monitoring of large, complex structures. The systems provide distributed, high-channel-count and remote monitoring for highway overpasses, roads, buildings, and bridges.
-
product
Rain Test Chamber - Twin Shower
The Drive-In Rain Test Chamber is generally used to conduct whole body testing of assembled vehicles under different rain test procedures to study and estimate their structural degradations and destructions induced by rain/water. The twin shower area with 1.1 million litre & 0.35 million litre volume is enclosed in a shed where arrays of pipes are interconnected to form zones to ensure the uniform spraying as per JSS 55555 test standard. The water gushes through the nozzle at a flow rate of up to 288 cu m/hr and the test chamber water collection system have a central grating with sufficient slope to collect the sprayed water during operation and circulate it back to the water reservoir to ensure close loop circulation.
-
product
Accelerometers
Dytran accelerometers are used for product testing & development, structural monitoring, and industrial machinery health monitoring management. We offer a wide range of piezoelectric & VC MEMS sensors.
-
product
General Purpose Single Axis Accelerometers
Motion of a rigid body can be characterized within six degrees of freedom. Providing mechanical excitation to simulate this motion as may be encountered in the real world can entail a variety of test machines. There are various pound/force vibration shakers for structural testing. Regardless of the apparatus, the goal is always to ensure that the product under test can adequately perform, and reliably survive, in the environment in which it will be deployed, or to which it will be exposed during transport. PCB® accelerometers provide the measurement signals needed to control the vibratory input and to analyze the product’s reaction to such testing.
-
product
Multi-channel low-pass filter board
AAF-2
The AAF-2 is a multi-channel low-pass filter board designed for use in front of A/D converters with resolution up to 16-bits. It is ideal for filtering applications in sound and vibration testing, ultrasonics, acoustics, structural analysis, industrial, test, scientific and laboratory data collection and applied mechanical applications in electronics, aerospace, field research, automotive, and process control industries.
-
product
Microcalorimeters
TA Instruments’ Isothermal Titration Calorimetry (ITC), Differential Scanning Calorimetry (DSC), and Isothermal Calorimetry systems are powerful analytical techniques for in-depth characterization of molecular binding events and structural stability. Thermodynamic binding signatures not only reveal the strength of a binding event, but the specific or nonspecific driving forces involved. Structural stability profiles from DSC reveal strengths and weaknesses in higher order structure and define the behavior of individual domains and their interactions. The TA Instruments Affinity ITC, Nano ITC and Nano DSC provide the performance, reliability and ease-of-use required for the most demanding applications in drug discovery, protein-protein interactions, structure-function characterization and more.
-
product
Modal Exciters & Amplifiers
Experimental modal analysis, or modal testing, is a process for physically obtaining a math model of a structure’s dynamic properties. Modal tests identify a structure’s modal properties: natural frequencies, mode shapes, mass, stiffness and damping. Modal test results help troubleshoot resonant excitation from operating forces, validate and verify finite element models, predict the benefits of structural modifications, support design verification, and understand structural responses due to complex loading conditions.
-
product
ISO 26262 FMEDA Solution
OneSpin automates the FMEDA steps through a series of safety apps integrated in a comprehensive, interoperable flow that leverages structural analysis, formal proofs, and expert knowledge. The apps can be applied at chip level, and support both RTL and gate-level design models. Crucially, the OneSpin FMEDA flow does not require a test bench, reduce or eliminates slow and effort-intensive fault simulation, and quickly detects shortcomings in the safety architecture.
-
product
NI-9260, 51.2 kS/s/ch Simultaneous, 3 Vrms, 2-Channel C Series Voltage Output Module
783467-01
51.2 kS/s/ch Simultaneous, 3 Vrms, 2-Channel C Series Voltage Output Module - The NI‑9260 is an instrument-grade dynamic signal generator for testing the audio components and capabilities of consumer electronic devices and providing excitation in structural test applications. Unlike sound card-based solutions, the NI‑9260 can be deployed quickly and recalibrated to guarantee long-term measurement repeatability and decreased test time. It also features ±30 V overvoltage protection and short circuit protection.
-
product
Fatigue Testing And Certification
Fatigue engineering is subject to uncertainty, and data from well executed tests are used to validate conclusions made by analysis and to provide a basis for structural certification. Our staff have extensive experience in testing materials and components under slowly varying, static loads, and under rapidly varying cyclic loads. Tests under static loads are used to assess material properties or to assess the load-deformation behavior of structural components. Tests under cyclic loads provide time to crack initiation, time to failure, or measurements of crack growth over time. We have extensive experience in measuring fatigue crack growth behavior in metallic materials. Past programs have measured crack growth with microscopy and photogrammetry at the surface, cracked area with direct current potential drop, and through-thickness crack profiles with quantitative fractography. By assessing crack growth with a variety of experimental methods, we enable robust analysis validation for cases of complex cracking. Our capabilities in fatigue engineering allow for careful design of a fatigue test program. Whether the tests use constant amplitude loading or an irregular loading spectrum, we specialize in engineering the test that meet your needs. Much of our experience is in non-standard test programs, which require engineering to optimize the test setup. Few others match our capability and experience in fatigue test engineering.
-
product
Vibration Meter
The Vibration Meter is a multi-functional device designed for machine vibration measurement (cyclic condition monitoring and troubleshooting), production line quality control, as well as structural vibration assessment.
-
product
Structural Analysis Professional Software
Robot™
Robot Structural Analysis Professional software provides engineers with advanced BIM-integrated analysis and design tools to understand the behavior of any structure type and verify code compliance.
-
product
2-CH Pulse-Train Motion Control EtherCAT Module
EPS-7002
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
product
Fatigue Rated Low Profile Cells
Fatigue rated load cells are specifically designed for component durability and fatigue test machines where highly cyclical loading is present. These rugged load cells are extremely resistant to extraneous bending and side loading forces. They are used for material testing, component life cycle testing and structural testing. All fatigue rated load cells are guaranteed against fatigue failure for 100 million fully reversed cycles.
-
product
X-ray Microscopy
Xradia Family
✔ Characterize the properties and behaviors of your materials non-destructively.✔ Reveal details of microstructures in three dimensions (3D).✔ Develop and confirm models or visualize structural details.✔ Achieve high contrast and submicron resolution imaging even for relatively large samples.
-
product
Handheld Digital Multimeter, 6000 Count, True RMS, Auto, Manual Range, 3.75 Digits
72-7780
72-7780 digital multimeter is newly designed to offer users better performance and higher safety rating. Total over-load protection and unique structural design make it new type of multimeter with high performance/ price ratio and a best choice for electricians used in electrical maintenance and repair.
-
product
Structural Durability Products
Instron offers a wide range of Durability Testing Products such as Controller and Software modules, Hydropuls actuators (linear & rotary), Servo valves, Sensors, Power Packs & Accessories and Test frames & fixtures.
-
product
Shock/Bump Multifunctional Tester
DP-201
King Design Industrial Co., Ltd.
Shock or bump test mainly simulate the impact effects of product and its components encountered in usage and transit process. Through standard and high-reproducibility instant energy exchange, you can analyze the product ability to tolerate the strong external stress and the degradation of structural weaknesses to quickly obtain the data of structure strength, anti-shock appearance and anti-drop. Shock tester is one of destructive experiments, and do destructive test on the product to evaluate the product reliability and monitor the consistency of production line.
-
product
Tensile Test Methods For Plastics: ASTM D638
Resin materials (plastics) are found in a wide variety of items used on a daily basis. Recently, plastics have started to be used as structural materials in transportation equipment, such as automobiles and aircraft, due to their strength and light-weight nature. In these applications, it is important to understand the mechanical strength properties of these plastics. ASTM D638 specifies methods for testing the tensile strength of plastics and other resin materials and for calculating their mechanical properties, and outlines accuracy requirements for the test frames and accessories used.
-
product
System Level Test and Burn-in Solutions
System Level Test (SLT) is a paradigm shift from traditional structural and functional testing. The device is tested in a complete, integrated system to evaluate its compliance against specified requirements. The system approach allows for higher and more cost-effective test coverage especially for multi-function and non-deterministic devices. It also brings new integration and test challenges like: ..Designing test fixtures on Burn-in Boards with system components ...
-
product
MEMS DC Response Accelerometers
PCB® series 3711F, 3713F, 3741F, and 3743F MEMS DC response sensors are used to measure low frequency motion down to zero hertz. These accelerometers are used in applications such as structural monitoring, aerospace vibration testing, drivability, and gravitational force measurements. Each series includes a full scale measurement range from ± 2g to ± 200g and features low spectral noise with high resolution.
-
product
Semiconductor Equipment Manufacturers
Integrated Dynamics Engineering
With shrinking process geometries, new structural elements and a major increase in substrate size, the challenges to improving process yield and overall throughput have increased exponentially. These demands drive a stringent requirement for system stability and overall immunity from internal and external forces.
-
product
Brake Testing Technology
Maschinenbau Haldenwang GmbH & Co. KG.
The brake test technology is mainly used to test the effectiveness of the braking system of motor vehicles. Depending on the application, roller brake testers or a deceleration measuring device are used. These are available in different versions depending on the type of vehicle and the structural situation.
-
product
Structural Dynamics
Structural Dynamics by OROS - bump tests, operating deflection shapes, modal analysis, and more
