Filter Results By:
Products
Applications
Manufacturers
Test Light
-
product
IAC Test Light
3502
Peaceful Thriving Enterprise Co Ltd
For GM1987 and newer GM model 700 TBI and PFI fuel infection system with flat 4-pin connector. For GM vehicles with throttle body or port fuel injection systems, check the electronic control module signal that provides direction to the idle air control motor.
-
product
IAC Test Light
3501
Peaceful Thriving Enterprise Co Ltd
For GM1982 and newer GM TBI and PFI fuel infection system with square 4-pin connector. For GM vehicles with throttle body or port fuel injection systems, check the electronic control module signal that provides direction to the idle air control motor.
-
product
Live-dead_Live Meter Verifier
LDL-1100
The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 50 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL 1100 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.
-
product
Live-Dead-Live Meter Verifier
LDL-1200
The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 150 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL-1200 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.
-
product
Visual Fault Locators
*Visual Fault Locator, we can understand its function in the letter. It could be regarded to be part of OTDR and the fiber fault locator is cheap.*Fiber visual fault locator is a kind of device which is able to locate the breakpoint, bending or cracking of the fiber glass. It can also locate the fault of OTDR dead zone and make fiber identification from one end to the other end. Designed with a FC,SC,ST universal adapter, this fiber testing red light is used without any other type of additional adapters, it can locates fault up to 10km in fiber cable, with compact in size, light in weight, red laser output.*Fiber visual fault locators include the pen type, the handheld type and portable visual fiber fault locator. Fiberinthebox also supply a new kind of Fiber laser tester/ optical fiber pen/ fiber laser pen, it can locates fault up to 30km in fiber cable.*Welcome to our store. Contact us at sales@fiberinthebox.com or Live Chat with us. Save your money & time right now! Buy from optical fiber supplies at Fiberinthebox.com with your confidence.
-
product
Integrating Sphere
The simpler way to measure the total luminous flux of lamps and luminaires is to use an integrating sphere photometer system. It is a device to perform spatial integration of flux optically, thus the total luminous flux can be measured with one fixed photometer head and measurement can be instant. An integrating sphere photometer is calibrated with a total luminous flux standard lamp. A test light source is measured by comparison to a standard lamp calibrated for total luminous flux.
-
product
LED Analyser
Feasa
Each LED Analyser allows for simultaneous measurement of up to 20 different light sources as it measures Color and Intensity – Brightness Test. Light from the LEDs is transferred by Plastic Optical Fibers and transported to the LED Analyser board for accurate measurement and analysis. The Feasa Analyser has been engineered to test LED’s and other lighting devices such as LCD Displays automatically. Intrinsic Quality offers a LED tester demo unit that can be tried out for two weeks free of charge. Currently available for purchase, call to order:
-
product
IK Level Tester
IK07-10
IK ratings are defined as IKXX, where “XX” is a number from 00 to 10 indicating the degrees of protection provided by enclosures (including luminaires) against external mechanical impacts. The different IK ratings relate to the ability of an enclosure to resist impact energy levels measured in joules (J). IEC 62262 specifies how the enclosure must be mounted for testing, the atmospheric conditions required, the quantity and distribution of the test impacts and the impact hammer to be used for each level of IK rating. The IK test applicate on lighting luminaires test according to IEC60598 (GB7000) and IEC60068-2-75 (GB2423.55).
-
product
Functional & ICT Tester
igentic® 621t
Growing demand for light emitting diode (LED) products and increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. The igentic® 621t is a flexible PCB tester that ensures quality while increasing production. The tester can handle multiple PCB products and test for light measurements, resistance and push button or post detection, as required.
-
product
6-24V Car Circuit Tester
1953
Peaceful Thriving Enterprise Co Ltd
Check on 6-24V system. The alligator (earth) clip is suitable earth and the tip of the contact probe is placed onto the part to be used. If current is present the test light will glow.
-
product
LabVIEW Programming Service
DMC has successfully employed LabVIEW in many industries, including product development, R&D, high-tech manufacturing, and test engineering. Following are a few relevent examples: Laboratory Automation; Carbon Monoxide Detector Testing, Strobe Light Testing, Multi-Station Permeability Test Stand, Hydraulic Fluid Tribology Testing. Manufacturing Automation; Engine Cold-Test Characterization, Smart Battery Pack Manufacturing Test, Automotive Sensor Testing.
-
product
Mini MUTT Portable Trailer Tester
#9003A
Innovative Products of America
portable trailer tester for testing lights and electric brakes on light-duty type trailers (7 spade, 6 round, 5 and 4 pin). The Mini MUTT places a load on the trailer's electrical circuits to verify proper lighting function. The Mini MUTT is powered by an (optional) internal 12v battery,
-
product
Fully Automated In-line Test System For LED Light Engines
We are pleased to announce that we have received an order for the supply of a fully automated in-line test system for testing LED light engines from ASD Lighting, based in Rotherham. The solution provided, consists of an in-line handler fitted with a vision system. The camera software is capable of learning the position of all LED’s on a new pcb, thereby reducing the time to introduce a new product. In addition to identifying the location of any missing or faulty LED’s the tester measures the colour temperature of every pcb. An image is taken of faulty units with the location of any missing LED’s identified
-
product
Volt Tester
PPTVM01
The DC Voltage Tester is an easy-to-use tool that can quickly test for voltage. Perfect for testing batteries, lighting systems, trailer connections, and more. This voltage tester is self-powered with a 210 cm cable. LCD displays voltage readings from 5 volts to 35 volts.
-
product
AC Fuel Flow Signal Generator
TA-100
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
product
6-24V Car Circuit Tester
1954
Peaceful Thriving Enterprise Co Ltd
Check on 6-24V system. The alligator (earth) clip is suitable earth and the tip of the contact probe is placed onto the part to be used. If current is present the test light will glow.
-
product
10 PCS Deluxe Noid Light / IAC Kit
3610
Peaceful Thriving Enterprise Co Ltd
*Kit packs in a deluxe mold plastic case.*Set includes: 8 Noid lights for testing GM PFI, FORD TBI, GEO TBI, BOSCH 2, BOSCH PFI, GM TBI, GM SCPI and GM MULTEC 2.*One IAC signal test lights for GM 1982 or newer GM TBI and PFI fuel injection system, and one for GM Model 1987 or newer GM Model 700 TBI and PFI fuel injection system.
-
product
Non-Contact Voltage Testers
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
product
DC12V Heavy Duty Circuit Tester
TE6-0706
Hangzhou Tonny Electric & Tools Co., Ltd.
*Heavy Duty probe *Heavy plastic handle and insulated ground clip*Testers light up and/or buzz to indicate testing result*Lights for easy visibility.*Heavy duty coil cord or straight cord (optional).*Durably designed for a long service life*For testing 6-12 volt systems for wire breaks, shorts, fuses, lamps, relays, armatures and more.*Suite able for a broad range of household, car, trucks, boats, trailers, vans, motorcycles, industrial and commercial uses.
-
product
LED Power Driver Test System
Chroma C8000
Chroma Systems Solutions, Inc.
The Chroma 8491 ATS is equipped with optimized standard test items for LED driver testing (lighting & TV backlight). The user is only required to define the test conditions and specifications for the standard test items to perform the test.
-
product
FLuorescent Lamp And Ballast Tester
2210-20
The Milwaukee 2210-20 Fluorescent Lighting Tester is a new to world tool that tests fluorescent lighting fixtures and cuts troubleshooting time in half. The Fluorescent Lighting Tester delivers complete Lamp, Ballast and Pin testing. Test Lamps before or after installing, and test without dismantling the fixtures.Recognized for its innovation, the 2210-20 Fluorescent Lighting Tester will dramatically improve the productivity of professional electricians and maintenance technicians. Instead of a “replace and hope” strategy, users can test their lighting fixtures faster and easier. The 2210-20 Fluorescent Lighting Tester solves a top residential, commercial and industrial application.
-
product
6-24V Car Circuit Tester
1951
Peaceful Thriving Enterprise Co Ltd
Check on 6-24V system. The alligator (earth) clip is suitable for earth and the tip of the contact probe is placed onto the part to be used. If current is present the test light will glow.
-
product
LED Burn-In Test
Burn-in system, based on LXI instrumentation, for concurrent testing of up to 80 DUTs in a climatic chamber. Devices to be tested include modern light emitting diodes and LED modules.The system consists of 2 control cabinets, each with 40 independent supply and measurement channels. Each channel can be configured individually via the operator software (current or voltage, including the relevant limit values). The software supports logging of current and voltage values for each DUT on all 80 channels with a sampling rate of <1s. Additionally, the software and system also support digital I/O channels, e. g. for controlling the climatic chamber. Inputs for connecting temperature sensors are also provided.
-
product
Advanced Diagnostic Trailer Tester
Alpha MUTT
Innovative Products of America
The Alpha MUTT® takes IPA's industry leading Super MUTT® platform, and adds the ability to instantly save, store, and share inspection reports. It gives customers peace of mind with complete accountability through detailed reports and gives technicians a better, faster way to enter and track report results. The mobile, durable Alpha MUTT® tests trailer lights, air brakes, and ABS systems via a Bluetooth-connected tablet with IPA's custom diagnostic software suite.
-
product
EFI Test Light-GEO TBI
3413
Peaceful Thriving Enterprise Co Ltd
*Simply for testing: Disconnect the fuel injectors, plug in a Noid.*Quickly determines if the electrical signal present at the fuel injectors.*Light and crank the engine, a flashing Noid light indicates normal pulsing voltage.
-
product
EFI Test Light-Bosch 2
3416
Peaceful Thriving Enterprise Co Ltd
Simply for testing: Disconnect the fuel injectors, plug in a Noid. Quickly determines if the electrical signal present at the fuel injectors. Light and crank the engine, a flashing Noid light indicates normal pulsing voltage.
-
product
EFI Test Light-Bosch Type
3405
Peaceful Thriving Enterprise Co Ltd
EFI Test Light-Bosch Type
-
product
8 Deluxe Noid Light / 2 IAC Kit Plus One Fiber Optic Noid Light Extension
3621
Peaceful Thriving Enterprise Co Ltd
*Kit packs in a deluxe molded plastic case.*Set includes: 8 Noid lights for testing GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, GM MULTEC 2 and BOSCH 2.*One IAC signal test lights for GM TBI and PFI fuel injection system, and one for GM Model 1987 or newer GM Model 700 TBI and PFI fuel injection system. Plus one fiber optic Noid Light extension.
-
product
Miniature Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
These piezoelectric accelerometers are particularly suited for small and light test objects. Of particular advantage may also be their high resonant frequencies. Due to the piezoelectric principle with its wide dynamic range both high acceleration and lowest vibration can be measured with the same sensor.
-
product
Tabletop Light Fastness Tester
TF419
TESTEX Testing Equipment Systems Ltd.
Tabletop Light Fastness Tester is a powerful xenon instrument with affordable price for conducting accelerated tests of light fastness and photo stability test.
