Elcometer Limited
For more than seventy years Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings, concrete and NDT industry.
- +1 248 650 0500
- +1 248 650 0501
- sales@elcometer.com
- 6900 MIller Drive
Warren, Michigan 48092
United States of America
Categories
-
product
Magnetic Thermometers
113
The magnetic thermometers are based on a bimetallic strip and therefore do not require batteries but do require time to adjust to the temperature.
-
product
Spray Equipment
Engineered for the most demanding automotive and industrial refinishing bodyshops through to the smallest independent workshop - whatever your spraying requirements, Sagola has the gun you need.
-
product
Pinhole Detection Inspection Kit
Elcometer 270
The Elcometer 270 Pinhole Detectors Inspection Kit utilises the wet sponge technique and has been designed to set a new standard for wet sponge detectors - a high quality, low voltage detector with similar accessories to a high voltage spark tester.
-
product
Chloride, Sulphate & Nitrate Kit
134 CSN
Supplied in an ABS plastic carry case for easy portability around the site, each field kit is supplied with full instructions attached to the inside lid, together with:5 x Chloride tests5 x Sulphate tests, together with 1 x colorimeter, for sulphate testing5 x Nitrate test strips5 x Syringes (without needles)
-
product
Motorised Clemen Unit
3000
The Elcometer 3000 Motorised Clemen Unit is a robust and accurate instrument for evaluating the resistance to scratching of a coated surface. The sample can be metal, wood, glass, plastic or other hard materials.
-
product
Coil Coating Wet Film Wheels
Elcometer 3230
The outer wheels are knurled to allow measurements to be taken on slippery coatings or on fast moving substrates.
-
product
Dry Film Thickness
Dry film thickness, coating thickness or paint thickness as it is often known, is probably the most critical measurement in the coatings industry. It provides vital information as to the expected life of the substrate, the product’s fitness for purpose, its appearance and ensures compliance with a host of International Standards. In 1947, Elcometer launched one of the world’s first non-destructive coating thickness gauges, the Elcometer 101 Coating Thickness Gauge. For more than 6 decades, the design and production qualities of this rugged and reliable instrument have been the watchwords for all our products and these philosophies are still held today. Elcometer has a comprehensive range of Dry Film Thickness gauges to meet all of your coating inspection requirements.
-
product
Drying Time & Permeability
When developing a coating process, it is important to know the exact time it takes for the coating to dry or cure. For multicoat paint systems, having knowledge of the drying time enables the operator to know when any subsequent layers can be applied. There are many stages involved in the coating drying time. Once a coating has been applied, it levels off under gravity, and, as the coating begins to cure, a thin dry film appears on the surface. The coating then continues to dry until, finally, it is totally cured.
-
product
Taber® Linear Abraser (230V/115V, 50/60Hz)
5750
Whatever your product, be it curved, round, big or small, the Linear Abraser from Taber® can test it all.
-
product
Crack Width Ruler
143
Elcometer 143 Crack Width Ruler is a simple gauge that has been designed to provide inspectors with a low cost alternative to a graduated microscope for determining the width of a crack in concrete or other building materials.
-
product
DIN Scratching Tool
1538
The Elcometer 1538 DIN Scratching Tool has interchangeable carbide cutters for the preparation of specimens to be used for corrosion testing.
-
product
Pinhole & Porosity
Premature corrosion of a substrate is usually due to a coating failure. A major cause is the presence of flaws in the finished coating. Collectively referred to as porosity, the main types of flaws are:
-
product
Protective Coating Inspection
Kit 4
The Elcometer Protective Coating Inspection Kit 4 provides a range of test equipment to help an inspector assess a substrate prior to the application of a coating.
-
product
Thickness Gauge
124
The Elcometer 124 Thickness Gauge is used to measure the peak-to-valley height of a surface profile moulded in the Elcometer 122 Testex® Replica Tape.
-
product
Mechanical Coating Thickness Gauges
Mechanical Coating Thickness Gauges are suitable for working in high risk areas such as high temperature or flammable atmospheres, underwater or where the risk of explosion is high and could be triggered by the use of an electronic instrument. From the simplest coating thickness gauge Elcometer 101 which will provide you with quick and immediate results to the more accurate coating thickness gauge Elcometer 211, also called the "banana gauge" which is ideal for cold and underwater surfaces.
