Gold
invaluable naturally occurring material able to withstand corrosion, highly conductive. Also known as: Au
See Also: Precious Metal, Platinum, Au, Gold Test
-
product
100 Gigabit Ethernet Rugged Rackmount Recorder
Talon RTR 2757
- Designed for data capture from Pentek Quartz® RFSoC products' 100 Gigabit Ethernet ports- Single QSFP28 port with MPO transceiver- Real-time record rates up to 12.5 GB/s (100 Gigabits/s)- Front-panel removable solid state storage up to 122 TB- Dual Intel Xeon® Gold processors with up to 4 TB of DDR4 SDRAM- 4U 19-inch industrial grade server chassis- Supports up to four independent UDP streams- SystemFlow software GUI with Signal Viewer analysis tool- C-callable API for integration
-
product
BNC (M) To Stacking Pin Tip Plugs
3901
BNC (m) to stacking pin tip plugs. Miniature banana plug springs are gold plated Beryllium Copper for excellent electrical connection.
-
product
Mini Coax, Contact, ITA, RG316
610103115
Primary mating contact 610104114. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 30µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 1 GHzVSWR ≤ 1.06 @ 1 GhzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzDWV 1500 VDC Min.Contact Resistance < 5 mΩ @ 0.5 Amp & always < 10 mΩCable Specifications RG316Environmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
product
LUTHER & MAELZER BARE BOARD TEST PINS
SERIES LMP 78
Materials and Finishes MATERIAL: Heat treated beryllium copper FINISH: 24 Kt gold plate over hard electroless nickel
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, 22-28 AWG, Crimp, 30µ" Au
610138216
*Please note: The difference between this p/n and 610138116 is the amount of gold plating. See below.P/n 610138116- 50µ" AuP/n 610138216- 30µ" AuPrimary mating contact 610138109. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCuContact Plating 30µ" Au over 100µ" NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force(lbs) 0.24
-
product
Micro Power, Contact, Receiver, 21 Amp, PCB Mount
610142102
Primary mating contact 610143101. (May mate with other ITA contacts, as well.)Specifications Operating Current 21 amps continuousContact Resistance 1.5 mOhms max.Dielectric Withstanding Voltage (DWV) 1500 VDC min.Contact Body BrassContact Plating 30µ" Au over 100µ" NiCycle Life 10,000 cyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 1.23
-
product
Coax, Contact, ITA, 20 GHz, RG 223, Crimp, 90 Series Modules only
610102117
Primary mating contact 610102116. (May mate with other ITA contacts, as well.)20 GHz coax contacts have an impedance of 50 Ohms and a current rating of 5 amps.It is recommended to use SF142 to achieve 20 GHz and RG223 to achieve 12 GHz.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield – Crimp/ClampInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 20 GHzVSWR 1.15 + .01 (f) GHz w/ RG142 (8 GHz)1.15 + .01 (f) GHz w/ SF142 (20 GHz)Insertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications RG 223 Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Voltage Variable Attenuators
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
product
Plugbord
4112-4
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers. 3-hole solder pads (0.28” x 0.080”) for interconnecting multiple component leads. Zig-Zag Bus Pattern on wiring side.Zig-Zag Bus Pattern provides access to voltage or ground at alternating hole positions. Continuous ground plane on component side with 0.085” etched clearance area around each hole Row and column legends provided
-
product
WR-8 Waveguide Straight
WAG-08-SXX
Precision mmw F-Band, WR-08, Straight waveguides are built with high precision and then gold plated for high corrosion resistance. They have very low loss and great VSWR. Manufactured to rigid specifications, these transmission line components provide minimum detrimental effects on the overall system VSWR.XX = length in inchesFeatures of WR-08, Waveguide Straights• 90 GHz to 140 GHz• Low Insertion Loss, typical for length• Low Return Loss, typical for length• UG-387 flangeView more WR-8 Waveguide Straight
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type D, Ø0.80mm, 155gf
K100-D080155-SKAU
K100 Series, Pitch 100mil, Tip Style D, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
product
Gold Detectors
Be prepared to dig deeper than ever before! With a Minelab Gold Detector you''ll find the elusive gold nuggets that others are missing! Minelab Gold Detectors are the FIRST CHOICE for: Professional gold prospectors, Small scale artisanal mining, Serious holiday gold prospecting, Weekend enthusiasts, Gold specimen collectors.
-
product
Micro Coax, Contact, Receiver, RG316 Double Shield
610140104
Primary mating contact 610141104. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor – SolderShield – SolderInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 10.5 GHzVSWR 1.0225 +.05 f(GHz)Insertion Loss -√f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications RG316 Double ShieldEnvironmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Ring Disk Electrode
This ring-disk type electrode developed by NTT Advanced Technology Corporation is a form of printed electrodes. Users can choose them from Carbon, Gold and Platinum applied versions. Available as a working electrode of radial flow cells, achieves complete reduction/oxidation on the center disk at ultra-low flow rate because of its fine coulometric electrolysis efficiency. This also enables to analyze subsequent reaction as well as identification and quantitation of the sample at the same time.
-
product
S-100 Bus, Vectorbord Plugbord
8801-6
VECTOR Electronics and Technology, Inc.
100 Gold plated edge contacts (50 each side)on 0.125"(3.175mm) centers. Pad per hole (square) both sides. I/O mounting area for ribbon cable header.Row and column legends provided. S-100 Form Factor.Pin 1 and 51 committed to power. Pin 50 and 100 committed to ground.
-
product
STD Bus, Vectorbord Plugbord
4610
VECTOR Electronics and Technology, Inc.
56 Gold plated edge contacts (28 each side)on 0.125"(3.175mm) centers. 3-Hole solder pads (0.28” x 0.080”) and buses forinterconnecting multiple component leads. Row and column legends provided.
-
product
Adapter/Gold
WADP-SMSM
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Plugbord
4066-4
VECTOR Electronics and Technology, Inc.
72 Gold plated edge contacts (36 each side)on 0.100"(2.54mm) centers. Overall ground plane on wiring side. Interleaved zig-zag bus pattern on component side.0.085” diameter etched clearance area around each hole on ground plane sideBus and plane surface solder coated for user convenienceRow and column legends provided
-
product
MODULAR
9000 SERIES
Flexible Vinyl Strain ReliefSoft Silicone Leads48" Length, 18 Gauge1000 Working Volts10 AMP RatedLow-resistance Gold ContactsRetractable Safety Shroud
-
product
Connectors, Header - Female
INT-10140
1x40 pin female header. These headers mate with square-pin 0.1" male headers. They can be cut into smaller segments, but please note that they are not break-away and at least one pin will be lost with each cut. Gold plated and RoHS compliant.
-
product
RF/Microwave Assembly Capability
Teledyne Labtech offers a comprehensive build-to-print microwave module and microwave components manufacturing service. This includes MMIC placement, Au wire bonding, SMT assembly and test.Our microwave MIC production facility is housed in a class 10,000 clean room that accommodates manual chip placement and semi-automatic wire bond assembly. Dedicated microwave components manufacturing is undertaken within production cells established to meet specific customer or product requirements.
-
product
STD Bus, Vectorbord Plugbord
4610-1
VECTOR Electronics and Technology, Inc.
56 Gold plated edge contacts (28 each side)on 0.125"(3.175mm) centers. No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
product
Metrology Software
ZYGO has been developing metrology software for decades – our commitment to helping our customers measure confidently, and the heart of our quality guarantee. Our original instrument software, MetroPro, established itself as a gold standard in the optical metrology world. Now, its successor Mx continues that legacy: trusted, easy to use, and heavily customizable.
-
product
Working Electrodes for Flow Cell
Our working electrodes for flow cell are mounted in blocks of PEEK. This resin protects the electrodes from external noise and allows researchers to utilize them regardless the content of mobile phase of HPLC because of their hardness and organic slovent-resistance. Glassy carbon is usually chosen for the redox reaction study on liquid chromatography. Platinum, Gold, Carbon paste and Nickel electrodes are utilized for special purporses.
-
product
Vibrator Test System
Sandwich Box Kit
"Gold standard” for vibrator tests provides more information than radio, wireline similarities or internal analysis. Other forms of vibrator QC use the vibrator controller accelerometers to measure vibrator motion. The Sandwich Box system includes external accelerometers which are used to independently record vibrator motion, thus providing a check of the whole vibrator system including the accelerometers.
-
product
BARE BOARD TEST PROBES
Probe Technical DataMechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current60 18 mOHMS mean63 60 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper60 24 Kt gold plated over nickel63 24 Kt gold plated over nickelBARREL: Nickel silver60 24 Kt gold plated ID and OD over nickel63 No FinishSPRING: Music Wire, 24 Kt gold platedover nickel
-
product
Signal, Contact, ITA, TriPaddle, 10 Amp, 14-18 AWG
610110129
Primary mating contact 610110128. (May mate with other Receiver contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Integrating Spheres
Artifex Engineering GmbH & Co. KG
We offer integrating spheres made from a special polymer suitable for the wavelength range 250nm – 2.5 µm. For longer wavelengths in the range 700nm – 20 µm, a gold coating on a rough, metallic surface is used. Since lasers in this spectral range are usually also high power, we use solid copper as a thermally conductive substrate material. By choosing the size of the integrating sphere, the overall sensitivity of the system can be adjusted. In addition, the detector is independent of inhomogeneities in power density and polarization. The detector is also independent of the incidence location and angle of the laser radiation.
-
product
PCIe Adapter for XMC
PCIe4LXMCX1
Simple and easy to use. Install PCIe4LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position. XMC´s with up to 8 lanes can be used. The PCIe lanes to/from the XMC are routed per PCIe specifications with matched lengths and impedance control.
-
product
Coax, Contact, ITA, 20/26 GHz, Flex 402
610102118
This contact available as a patchcord only. Please select link below to configure a patchcord.Primary mating contact 610102119. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield-SolderInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 26 GHzVSWR 1.25 for 2 - 18 GHz1.30 for 18 - 26 GHzInsertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications Flex 402 (Only Available in Patchcords)Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MΩ Min.
