Gold
invaluable naturally occurring material able to withstand corrosion, highly conductive. Also known as: Au
See Also: Precious Metal, Platinum, Au, Gold Test
-
product
Stator Test Systems
Automation Technology's STS-3800 has become the "gold standard" in Stator Testing Equipment. The STS-3800 is packed with standard features and like all of ATI's 3800 Series Test Systems, it is backed by the industry leading two-year limited warranty. The STS-3800 offers the most comprehensive testing of stators and fields available.
-
product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110177
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 26-30 AWG
610138112
Primary mating contact 610138116. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
Time-Resolved Electrochemical Quartz Crystal Microbalance
400C Series
The quartz crystal microbalance (QCM) is a variant of acoustic wave microsensors that are capable of ultrasensitive mass measurements. Under favorable conditions, a typical QCM can measure a mass change of 0.1-1 ng/cm2. QCM oscillates in a mechanically resonant shear mode under the influence of a high frequency AC electric field which is applied across the thickness of the crystal. Figure 1b below shows an edge view of a QCM crystal undergoing oscillatory shear distortion. The central portions of the top and bottom of the crystal are coated with a typically disk-shaped thin metal film (e.g., gold).
-
product
Micro Coax, Contact, Receiver, 50 GHz
610140108
Primary mating contact 610141108. (May mate with other ITA contacts, as well.) *This contact sold as a patchcord only.Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 30µ" Au over 100µ" NiContact Termination Solder Nut ClampInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC-50GHzVSWR 1.06+0.004 f(GHz)Insertion Loss - .095 x √f(GHz) dBDWV 700 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications Flex 405Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Miniature Two-Point Probe Set
PRF-922B
The PRF-922B Miniature Two Point probe accurately measures point-to-point resistance of small areas. Like Prostat's PRF-912B Miniature Concentric Ring, the PRF-922B is capable of measurements up to 1.0x1012 ohms. Built-in distance stops provide consistent electrode to sample pressure for developing repeatable measurements. Use the PRF-922B to measure small material samples, hard to assess molded areas, edges of parts, tray or tape cells and other very small objects and surfaces. The assembly is supplied with replaceable conductive electrode covers to enhance contact resistance on irregular surfaces and composition materials. Thus, measurements may be made with either the gold plated electrode contacts, or via conductive rubber covers.
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Square Post for Wire Wrap
610138118
Primary mating contact 610138200. (May mate with other Twin Female contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type I, Ø1.26mm, 305gf
K100-I126305-SKAU
K100 Series, Pitch 100mil, Tip Style I, Tip Diameter Ø1.26mm, Spring force 305gf, Steel with Gold Plating.
-
product
Mini Power, ITA, 36", 50u Gold (22 Amps), 16 AWG White Teflon (19 Amps), Single-Ended
7-243916000-036
Mini Power, ITA, 36", 50u Gold (22 Amps), 16 AWG White Teflon (19 Amps), Single-Ended
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type A, Ø0.80mm, 230gf
K100-A080230-SKAU
K100 Series, Pitch 100mil, Tip Style A, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
product
Power Supplies
ZPG-1200B
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type D, Ø0.80mm, 230gf
K100-D080230-SKAU
K100 Series, Pitch 100mil, Tip Style D, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 230gf
K100-C150230-SKAU
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
product
Extender
3690-2
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Plugbord
3662-2
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
product
Mini Coax, Contact, ITA, one .025"
610103150
Mini Coax, Contact, ITA, one .025" Round Post/ one .02" Square Post/ .075" Spacing.Specifications Characteristic Impedance 50 OhmsFrequency Range DC to 1 GHzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzVSWR ≤ 1.06 @ 1 GhzOperating Voltage & Current 0.5 Amps Max. ContinuousMating Force 1.5 lbs Max [0.68Kg]Dielectric Withstanding Voltage (DWV) 1500 VDC Min.Insulation Resistance 1000 MOhms Min.Contact Body Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter conductor – 60µ" Au over 100µ" NiCycle Life 20,000 Cycles
-
product
Power Supplies
ZPG-600B
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
product
Wide Jaw Kelvin Lead Set
6730
Wide Jaw Kelvin Lead Set. True wire four wire lead set with gold plated alligator clips that open to a wide .800? (20.3mm).
-
product
Rectifier Diodes
Chip Diodes from Bourns has emerged that offers the capability to provide a silicon diode with minimal packaging overhead. The small signal 0603, 1005 and 1206 Chip Diodes are lead free with Cu/Ni/Au plated terminations while the other packages (SMA, SMB, SMC, 1408, 1607, 2010, 2419, 8L NSOIC, 16L NSOIC, SOT23, SOT23-6, 16L WSOIC) use 100% Tin terminations. All Bourns® diodes are compatible with lead free manufacturing processes, conforming to many industry and government regulations on lead free components.
-
product
Cross Flow Cell
Working electrodes for flow cell are mounted on blocks of PEEK. This resin protects the electrodes from external noise and allows researchers to utilize them regardless the content of mobile phase of HPLC because of their hard, organic solvent-resistance. Glassy carbon is usually chosen for the redox reaction study on liquid chromatography. Platinum, Gold, Carbon paste and Nickel electrodes are utilized for special purposes. Thin Layer Cell has been used as a electrode for research such as flow injection analysis (FIA) and the HPLC.
-
product
Micro Coax, Contact, ITA, RG178
610141102
Primary mating contact 610140102. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 3 GHzVSWR 1.22 @ 3 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications RG178Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Radio Frequency Cable Tester
RFCT
Textron Systems’ Radio Frequency Cable Tester (RFCT) allows for on-site testing and maintenance for radio frequency (RF) transmission paths within a platform. Using preconfigured databases of sweep parameters and pass/fail criteria, the RFCT quickly determines the status of installed RF cables. The RFCT checks each cable’s performance characteristics to include voltage standing wave ratio (VSWR), insertion loss (IL), phase and phase matching. If a cable fails a test, the RFCT automatically determines the distance-to-fault (DTF). With its intuitive touchscreen-based user interface and lightweight, ruggedized packaging, the RFCT is the gold standard for operational-level RF cable testing.
-
product
LUTHER & MAELZER BARE BOARD TEST PINS
SERIES LMP VZ
Materials and Finishes MATERIAL: Heat treated beryllium copper and music wireFINISH: 24 Kt gold plate over hard electroless nickel
-
product
Multibus Extender
3690-18
VECTOR Electronics and Technology, Inc.
Length : 7.65"(190.5 mm)Height : 12.0"(304.8 mm)Contacts : 30 Contacts each side on 0.100" centers 43 Contacts each side on 0.156" centersConnector : Gold plated, mounted on top and connected to circuit tracesCurrent Rating : 5 amps at 10°F rise
-
product
DMM MULTIMETER TEST LEADS
Flexible Vinyl Strain ReliefSoft Silicone Leads48" Length, 18 Gauge1000 Working Volts10 AMP RatedLow-resistance Gold ContactsRetractable Safety Shroud
-
product
Adapter/Gold
WADP-SFSF
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Power Supplies
ZPG-500B
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
product
MANIA TEST PROBE
SERIES 76
ElectricalMAXIMUM CURRENT: 3 amps continuousat working travel, non - inductiveRESISTANCE: At 35 mA test current,50 mOHMS meanMaterial and FinishesPLUNGER: Heat treated berylliumcopper, FINISH: -2E / -2P Hard nickel plated-2D / -2E138 24 Kt gold plated,BARREL: Phosphor bronze, nickel platedSPRING: Stainless steel, silver platedPIN: Music wire, hard nickel plated
-
product
2U 19” Edge Server with Intel® Xeon® Scalable Silver/Gold Processors for 5G MEC Infrastructure Deployment
MECS-7210
The MECS-7210 Edge Server focuses on the edge of 5G networks to provide an open, white box platform for 5G Open RAN, private 5G networks, and a wide range of 5G MEC applications including smart cities, retail, manufacturing, autonomous vehicles, Argument Reality(AR), virtual reality(VR) and healthcare. As one of the first NGC-Ready validated and OTII compliant edge servers, the MECS-7210 is designed to meet stringent requirements by delivering a high level of deployment flexibility, reliability, scalability, and carrier-grade processing performance further augmented by hardware expansion. With a 420mm system depth in a small footprint 2U chassis, all I/O front access, wide operating temperature support (-5°C to +55°C), and dual FHFL PCIe expansion slots reserved for access to acceleration hardware such as GPU, FGPA and QAT adapters, ADLINK’s MECS-7210 is a high performance COTS platform that meets varying application and deployment requirements, and enables customers to focus on differentiating their end solutions.
-
product
Waveguide Twists
Fairview Microwave’s precision waveguide twists operate from 18 to 110 GHz across seven frequency bands with waveguide sizes ranging from WR-42 (18 GHz) to WR-10 (110 GHz). Our portfolio of waveguide twists feature gold plated brass construction that offers excellent electrical performance with VSWR as low as 1.02:1 and insertion loss as low as 0.2 dB. Both 45° and 90° waveguide twists are available from stock, with the 45° versions being available in both right hand and left hand twist configurations. All of our waveguide twists are in-stock and ready to ship today!
