PD
voltage discharge within an insulator causing dielectric breakdown.
See Also: Partial Discharge, Partial Discharge Detection, Partial Discharge Monitors, PD Test, Partial Discharge Test
-
Product
Handheld PD Tester
-
Weshine Electric Manufacturing Co., Ltd
TEV partial discharge inspection instrument uses two emerging technologies, transient-to-ground voltage (TEV) measurement and ultrasonic (US) measurement, to detect faults in switchgear. The equipment is portable and easy to operate. The TEV sensor is attached to the wall of the box, and the US sensor scans and detects along the gap on the switch cabinet.
-
Product
PD Monitoring systems
TECHIMP PD Hub™
-
Techimp’s Partial Discharge (PD) Monitoring systems usually consists of a Central Unit and distributed Data Acquisition Units – the PD Hub™ - able to acquire and process the PD signals locally detected through PD sensors installed on each of main electrical assets (generator, transformer, HV cables and GIS).
-
Product
PD Test Systems
-
1. Number of channels: 2/4 electric signal interfaces & 1 EXT interface 2. Sampling frequency: maximum 200MGa/s 3. Sampling precision: 12bit 4. Range: 0.1mV~20V 5. Range switch: 1mV, 2mV, 5mV, 10mV, 20mV, 50mV, 100mV, 200mV, 500mV, 1V, 2V, 5V 6. Frequency band range: 1Hz-60MHz 7. Range non-linear error: 5% 8. Range of capacitance for test object: 6pF~250µF 9. Power source mode: internal lithium cell / AC 220V 10. Display: 6.5 inches TFT LCD 11. Resolution: 640×480 12. PV: 4GB 13. Hard disk: 32G stiff disk used for storing the test data
-
Product
PD Free Test Transformer
-
Wuhan Fanke Transformer Manufacture Co., LTD
PD Free Test Transformer
-
Product
Cable Partial Discharge (PD) Spot Testing And Locating
PrecisePD
-
PrecisePD is an on-line PD Spot Testing and PD location system for Cables and Switchgear with advanced signal processing, used for the detection of PD in high noise environments.
-
Product
PoE Testing Chassis & PD Emulation
-
Can test the PoE performance of the DUT. In addition, it has a function of bypassing data, supporting fast Ethernet data transmission.
-
Product
Handheld Online PD Detector
PD-SGS
-
Quick identification of PD activities in switchgear and cable accessories. The BAUR PD-SGS handheld online PD detector is used to conduct rapid initial tests for PD activities on live switchgear. Potential weak points are immediately signalled acoustically and numerically.* Initial rapid condition evaluation of switchgear and cable accessories during mains operation* Ideal for quick checks of MV and HV switchgear* Two integrated sensors:TEV sensor records PD on the surfaces of switchgearsAcoustic sensor records PD inside switchgears* Greater safety for test personnel switchgear tested for safety risks before starting work
-
Product
PD Pipe & Cable Locator
PD / PD-H
-
Audio frequency 750cpsMaximum 100v outputFine Tune knob and LED's to easily match maximum impedanceInterrupter feature on oscillatorLCD meter on receiverReceiver loud speaker or headset useHoliday detection on buried pipe (PD/H)
-
Product
PoE LLDP Emulation (PD) & Analysis for 802.3at & 802.3bt
802.3at and 802.3bt PD Emulation and Protocol Analysis
-
Integrated PoE LLDP and Load Emulation in a Single Instrument. IEEE 802.3at and 802.3bt LLDP Compliance Analysis. Independent, Per-Port 802.3at and 802.3bt LLDP Emulations. Flexible Single and Dual Signature PD LLDP Emulations. One-Click LLDP Protocol Capture and Analysis. Pop-Up Excel Spreadsheet Reports Assess Protocol Content and Timing. Enables One-Click Emulated Power-Ups and Standard Waveforms with LLDP Power Granting PSE's. Enables 2-Pair and 4-Pair PSE Conformance Test Suties with LLDP Capable PSE's. Enables 2-Pair Multi-Port Suite with LLDP Capable PSE's. Available for PSA-3000 and PSL-3000 Platforms.
-
Product
Bi-Directional-Coaxial LD/PD Module
BiDi-F1000 (FTTx)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Laser optical: DFB or FP. DFB laser optical: with isolation or without isolation. Low threshold current and operating current. High output power. Built-in InGaAsP monitor PD. High responsivity, InGaAs planar PIN detector. Wide temperature range operation(Tc=-40℃to+85℃). Fiber ITU-T G.657 Bending low loss, fiber optic cable features
-
Product
PoE PD Test Solutions
-
Explore PoE PD Test solutions from Sifos Technology. What type of testing does your Power-Over-Ethernet Powered Device need?
-
Product
PD free AC Hipot Test Set
FPA Series
-
FPA Series test sets perform field or factory testing on larger electrical apparatus, including motors & generators, switchgear, bushings, bus duct, etc. This series offers the higher kVA ratings needed (0-6/12 kV AC @ 6 kVA), but is still packaged for portability.
-
Product
PD Coupler
-
Techimp Capacitive PD Couplers offer both the PD and sync signals references, allowing a thorough investigation of the signal originating inside the asset they are connected to.Techimp Couplers are individually tested according to the following international standards: IEC60358; IEC60694; IEC60270.
-
Product
PoE LLDP Emulation (PD) & Analysis for 802.3at & 802.3bt
-
The optional LLDP Emulation feature allows a PSA-3000, PSL-3424L, or PSL-3000 test port to behave just like an 802.3at or 802.3bt PD that uses LLDP to convey its power demands. 802.3 PoE LLDP is a special variant of LLDP protocol that involves handshakes and protocol timing between a PSE and a PD.
-
Product
ITSM Synchro
-
The Impulsive Test Synchronization Module (ITSM) is a device aimed at generating a digital synchronization signal, to use the PDBaseII system for impulsive voltage PD test. The digital synchronization signal generated by the ITSM, is synchronized with the voltage impulse of the impulsive source (voltage generator). The ITSM must be connected between the DIN channel of PDBaseII and the output of the synchronization sensor (e.g. capacitive coupler). The ITSM provides also a low voltage signal reproducing the impulsive voltage source.
-
Product
Field Testing Services
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT offers three levels of testing services both domestically in the US and globally. With the best quality products, complete PD solutions, rich on-site testing experience, experienced partial discharge experts and field engineers, PMDT also provides PDExpert Services -- professional on-site partial discharge detection and location services to help the customers find the potential risks, evaluate the operating status of the electrical assets, and deliver complete and final problem solutions.
-
Product
Portable PD Monitoring of Medium and High Voltage Power Equipment with UHF, AE, and HFCT
PDiagnosticM
-
Power Monitoring and Diagnostic Technology Ltd.
The PDiagnosticM is a portable system that utilizes UHF, AE, and HFCT sensor modules to monitor PD signals from Medium and High Voltage power equipment.The system is ideal for monitoring critical power assets to find and monitor intermittent PD signals and to analyze the developing PD trends. The PD type is determined by automatic pattern recognition and internal defects can be found at an early stage.The system provides advanced protection with alarm functions and our Deep Learning data analysis capabilities utilizing our proprietary Intelligent Cloud Diagnostic Technology.
-
Product
Spiral Antenna UHF Trafo
-
UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain. Its compact and robust design (passive sensor) makes Spiral antenna the optimal sensor for direct installation on high voltage Transformers. It can be virtually applied in any electrical equipment provided that it has apertures or EM transparent surfaces. Contact our sales department for consulting.
-
Product
Flexible Magnetic Coupler
FMC
-
The FMC (Flexible Magnetic Coupler) is a partial discharge sensor whose working principle is based on a direct magnetic coupling with the cable conductor and shield.It picks up a magnetic signal given by PD activity. His compact and robust design makes the FMC the optimal sensor for direct installation on cables and accessories such as joints and termination.This sensor has a sensitive side which has to face to the object under test, while the other side (shielded) reject the noise from the environment.
-
Product
PoE Tester
PE-100
-
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotation between voltage (Volts), current(Amps) and power(Watts) via dual 4 digit 7 segment LEDs which provides voltage available, current flowing and how much power an PD actually need ensure sufficient power for PD to make the PoE is sustainable.
-
Product
Laser Diode Drivers
-
Arroyo Instruments offers a broad range of laser drivers to meet your exact test needs. From 100 milliamps to 100 Amps, all of Arroyo Instruments' LaserSource benchtop laser drivers include unique features not found on competing products such as optically isolated photodiode and modulation inputs, programmable PD bias, and both RS232 and USB computer interfaces. The LaserSource also has laser diode protection circuits such as interlock, ESD protection, and hardware limits for current and voltage.
-
Product
Temperature Controller
2500
-
The Series 2500 Temperature Control provides an impressive array of features in an economical 1/4 DIN package. Features include on-off, time proportioning, proportional, PI, PD, or full PID control, programmable from the front panel, or use Self-Tune PID.
-
Product
Ethernet Powered Device Analyzer
PDA-604A
-
Emulate any 802.3at Type-1, Type-2, 802.3bt Type-3, or Type-4 PSE powering 2 or 4 pairs at all possible PD input voltages. Optionally supports 802.3at and 802.3bt Ethernet Powered Device Conformance Test Suites and LLDP Emulation and Analysis.
-
Product
USB PD Test System
6050
-
Single Output USB PD USB PD basic version：the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
Product
PD Conformance Test Suite for 802.3at & 802.3bt
-
Sifos Technologies offers the ultimate simplicity in testing a PD’s conformance to IEEE 802.3 Standards with Pass/ Fail reporting in the PD Conformance Test Suite available for purchase with the PDA-600 Family of Instruments.
-
Product
Shielded Rooms
-
HIGHVOLT Prüftechnik Dresden GmbH
Electromagetic field and line-conducted interference needs to be eliminated in order to measure low-intensity partial discharges with a PD background noise level (≤ 1 pC) in accordance with IEC 60270.
-
Product
Measurement Of Surface Tenison Using The Pendant Drop Method
SURFTENS PD
-
Optik Elektronik Gerätetechnik GmbH
SURFTENS PD is an image processing software for measurement of surface tension of liquids by pendant drop method. By help of drop shape analysis the surface tension is calculated, using the form parameters of the pendant drop. SURFTENS PD is used in connection with OEG equipment, but also available as standalone solution for applications of customer.
-
Product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
Chained Data Test Support for 802.3at and 802.3bt PSE's
-
Intuitive graphical user interface. Configures up to 24 2-Pair or 4-Pair ports for "snaked data path" testing. Verifies all PSE connections in the defined data path. Sequences user-defined PD emulations and PSE powering.Verifies powering to user-defined loading on all selected ports. Configures looped data paths across the selected ports. Support of 802.3at / 802.3bt LLDP power negotiations (PSL-3424L).
-
Product
Online PD Spot Tester
Liona
-
Cable testing and diagnostics with the BAUR liona. Liona is a portable online PD spot tester for measuring and locating partial discharges in cables and switchgear during normal mains operation. Liona lets you test cable systems and electrical equipment online without switching off partial discharge activities, and then generate trend analyses. Even a PD spot test (duration: 5-10 minutes) is capable of reliably assessing the current status of your system.* Automatic PD detection during normal mains operation (without switching off the cable route)* With DeCIFer technology: PD identification based on 500 million measurement results* Precise online PD mapping with PD transponder
-
Product
PoE Service Analyzer
-
The PowerSync Analyzer adapted to comprehensively assess PoE service at any PD outlet
