-
Product
High Precision Energy Meter Test Bench
SY8330
-
Hong Kong Songyang Industrial Ltd.
SY8330 Series Three Phase Energy Auto-calibration System is a new generation, high precision, multifunctional energy meter calibration equipment. It uses the international’s most advanced technology and components available in 90 decade. It can be widely used to calibrate different kind of single phase energy meter both channel & three phase energy meter or multifunction power meter.
-
Product
Electro-optic Test Bench for IR Detectors
BIRD 210
-
Testing detectors requires the implementation of ultra-low noise driving electronics and presenting high quality optical stimuli to the detector under test. This meets all these requirements and allows to test any type of detector by easily implementing the detector’s driving signals and providing exhaustive and accurate measurement results.
-
Product
T9731 High-performance Flow Test instrument with continuous measurement for EN 14683
-
The T9731 is specifically designed for measure the adequate air flow rate in complete adherence to the standard EN 14683 for surgical masks testing.Full scale from 10 mbar to 10,000 cc/minFlow measurement accuracy : 1% RDG + 0.1% FSFlow measurement resolution : 1 cc/minDirect pressure accuracy : 0,5% RDG + 3 DGTDirect pressure resolution : 0.001 mbar (0.1 Pa)
-
Product
Test Automation Services
-
Increase testing ROI while improving test effectiveness and maintainability.Today, quality engineering is all about involving testing earlier in the development cycle, with automation being the driver. Our test automation specialists will implement the appropriate automation solutions for your business for the benefit of quality. Learn more about our test automation services below!
-
Product
4, 8 and 16 Channel ARINC429 Test and Simulation Module
ANET429-x
-
The ANET429-x is a member of AIM’s Ethernet based modules for analysing, simulating, monitoring and testing ARINC429 channels.
-
Product
IPX56 Simulation Rain Test Chamber
CX-IPX56A
-
Shenzhen Chuangxin Instruments Co., Ltd.
IPX56 Simulation Rain Test Chamber widely used in the lamps and electrical and electronic product certification testing institutions and for testing the waterproof of electrical and electronic products of shell protection level.
-
Product
AFDX ® / ARINC 664 Test And Simulation XMC Module
XMC-664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
Longbow Launcher / LEA Test Set
TS-201B
-
The TS-201 is a state-of-the-art I-Level and Depot level test set for MIL-STD-1760 and legacy armament systems including launchers and bomb racks.
-
Product
Test Extender
PMC
-
The PMC test extender provides an active interface between a PMC carrier slot (PCI bus) and a PCI Mezzanine Card (PMC).
-
Product
Test-Stand Software for TD6 Controller for QMax ATE
TD6 TestStand Software
-
Qmax Test Technologies Pvt. Ltd.
The TD6 TestStand will enable the users to sequence and execute their own test programs. The user can browse his/her test program and add it to the TD6 TestStand component. The test program can either be in the form of DLL ( Dynamic Link Library ) or EXE ( Executable ). And, the user can add any number of steps. As of now, we will support only the .Net based test programs. Each and every individual assembly or exe added in the TestStand component will be considered as a single step. All such steps on the whole added in the TestStand component will be considered as 'Sequence'. The same is priced at Rs. 8,42,520.00 plus GST @18% extra. For further details, pls contact sales@qmaxtest.com
-
Product
Time Shift Test Java Applications w/in a WebLogic Managed Server
Time Machine Framework for WebLogic
-
The Time Machine Framework for WebLogic provides a great set of features enabling time shift testing scenarios for Java applications deployed to Oracle WebLogic. This Framework enables customers to use Time Machine functionality to time shift test Java applications within a WebLogic managed server without the need to create a separate instance of the application server for testing other time related activities. The Framework allows customers to configure and automatically create different virtual clocks on managed servers within the WebLogic domain as well as the granularity to establish virtual clock rules for specific applications deployed to the managed server.
-
Product
Tire Rolling Resistance Test System
-
This system measures the rolling resistance of each tire accurately. In addition to the simultaneous measurement of tire loss resistance and rolling resistance coefficient for each drive by mode operation (JC08, WLTC), coasting test, constant acceleration/deceleration test and transient mode test are able to be performed. Furthermore, measurement of driving noise/ vibration of the tire, effect of the tire loss due to the temperature change can be verified by adding options.Conforming the JIS D 4234: 2009 and ISO 28580: 2009.
-
Product
Transformer Test Equipment
-
DV Power test instruments perform various diagnostic tests on power and instrument transformers. Even more, a unique feature is a condition assessment of on-load tap changers. Performing a transformer test before their breakage can be crucial.Test instruments are portable and enclosed in durable metal cases. Also, the 19” rack-mounted version suitable for factories is available as well.Applications supported by DV Power transformer test equipment include:Winding resistance measurement (IEC 60076-1)Analysis of on-load tap changers (IEC 60214-1)Heat run test (IEC 60076-2)Automatic transformer demagnetizationTurns ratio measurement of power and instrument transformers (IEC 60076-1)Excitation current measurementPhase angle measurementTransformer vector group detectionDemagnetization status verificationAll of the above-mentioned measurements are performed with the highest accuracy.The advanced DV-Win PC software collects both numerical and graphical results. As a result of that, these features provide an easier and more efficient analysis. After the test, DV-Win software generates a test report with a single click. Furthermore, a user can easily customize the test report and save it in different formats, such as XLS or PDF.Finally, the analysis of on-load tap changers is performed by the new method called dynamic resistance measurement (DRM). This is a non-intrusive method. Therefore, it allows detecting problems in on-load tap changers without disassembling them.
-
Product
Thermal Shock Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Chamber provide the sudden temperature changes between extreme cold and extreme hot from -65℃ to 150℃ (customized available), specially for environmental stress screen test of the industries that rely on thermal testing, such as component, board electronic assemblies, defense, material stress, consumer products etc. The thermal shock test can cause faulting or cracking by the expansion and contraction on the products, indicates the hidden manufacturing defects. Bell’s Thermal Shock Chamber ensure you to launch qualified product to the market.
-
Product
Vibration Test Systems
G-5 Series
-
Both Shock tests at from relatively high acceleration(max. 4900m/s2 -500G) to low acceleration with wide pulse width, difficult to achieve with conventional Shock Test Systems and Vibration tests for not only IEC, MIL and JIS but also requiring higher acceleration, velocity and displacement than ordinary VTSs can be carried out with one system.
-
Product
EtherCAT Conformance Test Tool (CTT)
ET9400
-
The Conformance Test Tool (CTT) enables in-house testing of EtherCAT slave devices. The use of the CTT supports EtherCAT device development, helps to ensure conformance prior to device release and to prepare the device for the official, independent Conformance Test in an EtherCAT Test Center (ETC) accredited by the EtherCAT Technology Group.
-
Product
Highly Accelerated Stress Test Chambers
HAST
-
Our HAST systems have a modern design that's easier to use: Automatic humidity filling; Automatic door lock; A more square workspace; allowing more product to be loaded;Convenient, hermetic power-pin system for bias testing. We are now able to offer a hermetic port system to allow special signal lines like coax or fiberoptics to be run into the chamber.
-
Product
ARINC 429 Test And Simulation VME Module
VME-429
-
*8, 16, 32 or 64 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
-
Product
Walk-In Temperature & Humidity Test Chamber
-
Weiber walk in humidity test chambers are conceptualized and designed to create test chambers to study and contemplate the effects of different environmental parameters such as humidity, temperature applications tests involving micro-organisms, plants, tissues, electronic components etc. apart from various customized industrial and research applications. Our humidity test chambers have a variety of usage in R and D laboratories, research studies and product testing facilities across the globe. Apart from that, these chambers have a variety of usages in tissue culture applications, enzyme reaction studies, growth observation studies, fermentation analysis and various other general and specialized applications in various laboratories. We specialize in both standard and customized humidity test cabinets, specifically designed to meet the challenging demands of various scientists for individual and specialized research applications.
-
Product
SAE AS5643 Mil-FireWire PXI Express Test & Simulation Instrument
HSSUB-6120
-
Avionics Interface Technologies
Highest density capability available in an AS5643 3U PXI Express, single slot instrument - Four (4) FireWire nodes, each with three (3) ports - Apps provide high-level (AS5643) and low-level (1394) access, while accommodating end-user customization - S100, S200, S400, S800 transfer rates - Support all Nodes operating concurrently at 800 Mbps - Independent transformer coupling for each port - Eight (8) standard PXI backplane triggers - Industry standard Texas Instruments IEEE 1394b Chipset - ANSI C (typical), C++/C#/LabVIEW
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
Test System
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
LoRa Test Solution
-
To ensure optimal operation, LoRa devices must provide reliable and consistent performance. The IQfact+ LoRa offers an optimal solution to accelerate volume manufacturing testing while minimizing engineering effort.
-
Product
500KG MicrocomputerTensile Test Machine
CX-106
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Tensile Testing Machine is widely applied to test the tensile, tear, peel, and bend of all kinds of materials, such as metal, cable and etc, it’s used to test the tensile, tear, peel, compressive strength and bending of the material. It conforms to the standard of GB, ISO7500/1, JJG475-88, ASTME4, DIN5122, JISB7721/B7733, EN1002-2, BS1610, and CNS9471/9470.
-
Product
RFID Test Instrument
RAIN Xplorer
-
The CISC RAIN Xplorer is a unique RFID test product developed for convenient tag frequency sensitivity, communication range, and backscatter measurements. The RFID tester is designed for open area tests and measurements in an RF-controlled environment using portable or fixed RF test chambers. The system is supplied with software and a reference tag for self-calibration.
-
Product
Ionic Contamination Test Systems
CM+ Series
-
The Contaminometer (CM+ Series) system was originally developed by Protonique, the business of industry guru Brian Ellis. They also featured in the early development programmes of "cleanliness measurement" carried out by the US Department of Defense at China Lake in the 1970s. Historically, International Standard IPC-J-STD001 stated that assemblies be cleaned to a value of <1.5µg/cm2 of NaCl equivalence. However, the new design is linked to the introduction of the new process control metric introduced by Gen3 Systems: Process Ionic Contamination Testing. The CM+ Series measure the amount of ionic contamination in accordance with all existing test methods, often referred to as ROSE testing, as well as the new PICT test.
-
Product
IEC60335 Inclined Plane Test Table for Stability Test
CX-W600
-
Shenzhen Chuangxin Instruments Co., Ltd.
It's to determine the stability of electric appliances which are used on a table or on the floorin accordance with IEC 60065 / 1998-07 clause 19.1, IEC 60335-1 / 1991-04 clause 20.1, IEC 60601-1 /1988 clause 24.1, IEC 60950 / 1991 + Amendments, modified, clause 4.1.1,EN 60335-1 / 1994 and A11 / 1995 clause 20.1, EN 60950 / 1992 + Amendments up to 1997 clause 4.1.1,VDE 0700 Part 1 / 10.95 clause 20.1 and Part 3 / 3.96 clause 20.1, VDE 0730 Part 1 / 3.72 clause 20a,VDE 0805 / 11.97 clause 4.1.1Inclined Plane Device is used to test the stability of an apparatus that requires a surface in order to work.The device cosist of a surface and an angle adjusting device with 0- 15 °
-
Product
Vacuum Test Fixtures
Series 63
-
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
Product
MIPI Receiver Test Solution
M8085A
-
The M8085A is a software plug-in for M8070A Bit Error Ratio Test system software within the M8000 series of BER test solutions. The M8085A software plug-in controls either the M8190A or the M8195A Arbitrary Waveform Generators to create C-PHY or D-PHY standard compliant test signals. In addition it provides routines for calibration of all signal parameters and for all tests specified in the applicable Conformance Test Suite. Together with the additional available DUT control interface it is possible to read the BER of the receiver under test from the M8070A software and display the BER dependency from test parameters within the M8070A user interface.
-
Product
Battery Test Equipment
-
KV Hipot Power Test Equipment Co.,Ltd
Battery testers are the class of instruments designed to assess the condition—the charge, impedance, ripple current, or other measurement—of batteries to ensure they are working as required. Just as batteries have a very wide range of sizes and uses, so do battery testers.
