Filter Results By:
Products
Applications
Manufacturers
G.992.5
Doubles the bandwidth (ADSL) close up, boosts it nicely in middling ranges and pushes high-speed always-on data over telephone lines out to 18,000 feet.
-
product
3U VPX 1 Slot P&G with VITA 67.3D aperture
101V301P05-9002R
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
product
Voltage Input Device For FieldDAQ
The Voltage Input Device for FieldDAQ measures up to eight ±10 V channels with 24-bit resolution and simultaneous sample rates up to 100 kS/s/ch. Some models can power sensors, such as pressure sensors, with up to 24 V per input channel. This device offers 500 V channel-to-channel isolation, protecting instrumentation from high-transient voltages. Additionally, the device is IP65 and IP67 rated to be dust-proof and water-submersible, can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. It has an integrated network switch for simplified daisy chaining and provides tight synchronization over time sensitive networking (TSN) for distributed data acquisition systems.The Voltage Input Device for FieldDAQ includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Signal Splitter
The Dynamic Signal Buffered Splitter protects sound and vibration sensor acquisitions from the unwanted effects of a parallel troubleshooting or diagnostic instruments. G Systems Dynamic Signal Buffered Splitter provides buffered and unbuffered outputs connected to the same signal input. Up to 16 sensors, typically accelerometers, proximity probes, microphones, and pressure transducers, may be connected to the 16 signal inputs.
-
product
Outdoor Nodes
The upgraded Outdoor Nodes have been developed by the NITLab team and support MIMO operation. The new version of the Outdoor Nodes are equipped with 802.11a/b/g and 802.11a/b/g/n wireless interfaces. They also feature 2-core Intel cpus, new generation solid state drives and usb web cameras. Last but not least, each node is equipped with light, temperature and humidity sensors.
-
product
Electrical Swivels
Electrical Swivels enable the rotation of data and/or power cables and are designed to be integrated into the swivel stacks of Floating Production Storage and Offloading (FPSO) applications. They can withstand the typically harsh environments of the oil and gas (O&G) industry and are installed on vessels and/or floating moored platforms.
-
product
Quantum Gravimeter
The quantum gravimeter, the first commercial device of its kind in the UK, uses quantum interference of matter waves to measure the local value of gravitational acceleration, or ‘g’, with very high precision. Objects with different mass cause small fluctuations in the value of g measured on the surface of the Earth. The quantum gravimeter can be used to sense these objects hidden under the surface in a non-intrusive manner.
-
product
Speed Switch
M100T/M5000T
Features• Internal sensor• SPDT relay output• 5-100 rpm (M100T), 100-5,000 rpm (M5000T)• Terminal block for easy wiring• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• Works with Electro-Sensors magnetic pulser discs/wraps• Explosion proof (XP) housing• UL Listed Class I, Div I (C, D) Class II (E, F, G)
-
product
Large CMMs
In the aerospace industry, in vehicle and mechanical engineering as well as in many other fields, coordinate measuring machines with a large measuring range are required so that there is no need to compromise when it comes to precision. This is why ZEISS offers a wide range of tabletop, bridge-type and gantry coordinate measuring machines in various sizes. Large coordinate measuring offered by ZEISS include ZEISS ACCURA and the entire ZEISS MMZ product family (MMZ T, MMZ M, MMZ G).
-
product
3U 1-Slot OpenVPX P&G, Aperture E, VITA
101V301P03-9001
3U 1-Slot OpenVPX Power & Ground, Aperture E, Supports VITA 66.4/67.3A/67.1 in J2B, Module TE 2226880-1, Pass through with VITA 66.4 ctr in J2B, w/o ROHS, Max data rate (Gbps) 3.125.
-
product
Industrial Panel PCs and Monitors
Advantech provides HMI and monitors with C1D2 certification. Apply to asset monitor and data process in harsh environments like O&G or pharmaceutical.
-
product
Insulation Tester
AD-225
3 Measurement voltage range: 500 V; 1000 V and 2500 V, Control of measuring voltage during measurement, Insulation measurement up to 100 G W, Elimination of trough resistance insulation ? 3 connectors measurement method, Autoranging,
-
product
Calibrator, 0 to 24 mA, Current, 185 mm, 78 mm, 38 mm, ± 0.5%, 265 g
72-6694
*Adjustable 0 to 24 mA current source*Current calibrator drives loads up to 500 Ω*Large LCD display*Sampling Time : Approximately 0.4 seconds*Over Input Indicator : 1*Operating Temperature : 0°C to 50°C ( 32°F to 122°F)*Size : 185 × 78 × 38 mm (7.3 × 3 × 1.5 inches)*Weight : 265 g (0.58 lb) including battery*Requires one 9 V battery - not included*12 month limited warranty *view Terms & Conditions for details
-
product
MEMSIC 2125 Dual-axis Accelerometer
28017
The MEMSIC 2125 is a low cost, dual-axis thermal accelerometer capable of measuring tilt, acceleration, rotation, and vibration with a range of ±3 g. For integration into existing applications, the MEMSIC 2125 is electrically compatible with other popular accelerometers. MEMSIC provides the 2125 in a surface-mount format. Parallax mounts the circuit on a small PCB, providing all I/O connections so it can easily be inserted on a breadboard or through-hole prototype area.
-
product
Dual Accelerometer
M6
*Built-in damping and overrange stops*Safe overrange limits*Force up to 2000 G without damage to sensor*Temperature compensated for accurate response over entire temperature range*High slew rate operational amplifiers (1.2 V/usec)*Internal RF shielding on each pin
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type G, Ø1.50mm, 155gf
K100-G150155-SKAU
K100 Series, Pitch 100mil, Tip Style G, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
product
3-Lambda Power Meter
3λ-PM
•Simultaneous wavelength detection and calibration.•B / E / G – PON 3 wavelength power meter and insertion loss tester (1310 / 1490 / 1550 nm)•Simultaneous measurement of 3-wavelength PON signals•Automatic wavelength detection to save time and cost•Rugged, shock and water-proof for field use•Compact, lightweight and cost-effective•Quick and easy to operate
-
product
Portable Hardness Tester For cast/rough surface parts
PHT-1750
Loaded with features, this economically priced portable hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This portable hardness tester comes complete with the G impact device, calibrated test block and rugged carry case.
-
product
3U VPX 1 Slot P&G w VITA 66.4 connector in J2. 10G
101V301P04-9X13
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
product
3U VPX 1 Slot P&G w VITA 67.3D connector in J2
101V301P05-9003R
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
product
FD-11601, 8-Channel, ±10 V Powered-Sensor Voltage Input Device for FieldDAQ
786374-01
The FD-11601 measures up to eight channels with a voltage input range of ±10 V. Each input channel supports TEDS and provides 24 V DC to power external-powered sensors without additional power supplies. The FD-11601 features 24-bit resolution, simultaneous sample rates up to 100 kS/s/ch, and channel-to-channel isolation. It is IP65/IP67 rated to be dust-tight and water-submersible, operates in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11601 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11601 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. The FD-11601 is ideal for test cell and outdoor environments.
-
product
High Resolution Magnet Systems
EPR
EPR samples with S=1/2 electronic spins exhibiting a narrow signal at G=2 and require magnetic fields of only ca. 3.5 T. However, EPR spectra from S>1/2 spins are typically much broader and have spectral features that spread over magnetic field range of several Tesla.
-
product
20-50,000 Hz Charge Amplifier
203G8
The Trig-Tek™ 203G8 accepts pickupswith sensitivities varying from 1 to 110pC/g. It has three simultaneous outputs:Acceleration with a sensitivity of 100 mVrms/Pk g; Velocity with a sensitivity of 534mVrms/Pk/ips; and Displacement with asensitivity of 100 mV/mil DA.
-
product
3U VPX 1 Slot P&G w Reflex Photonics 415-00004 in J2
101V301P03-9005
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
product
Safety Compliance Test System
EN 60601
Test system for electrical safety compliance testing of medical products in accordance with EN 60601-1, 3rd edition.The system is equipped with three test fixtures which are connected in parallel order to reduce the number of setup tasks for different variants in the course of day-to-day manufacturing processes. Its purpose is to test medical products, e. g. patient monitors, which are employed at hospitals to monitor heartbeat and oxygen saturation.Based on the integrated electrical safety tester by Associated Research, in combination with an AC power source and a switching matrix, it is possible to fully automate tests like for instance AC/DC high-voltage tests, insulation resistance measurements, earth connection tests and leakage current measurements.The required occupational safety is provided by a high-voltage safety hood in accordance with EN 501191. The entire safety technology, as well as the control PC, is mounted in an aluminum-profile cart.
-
product
Integrated Hardness Tester With Impact Device G
TIME®5106
Beijing TIME High Technology Ltd.
TIME5106 dynamic type hardness tester is integrated with impact device G for testing solid components like heavy castings and forgings. It can perform hardness test in individual mode or in system mode.
-
product
WiFi Traffic Generators
LANforge WiFIRE
wireless traffic generator is an excellent choice for testing Access Points and other WiFinetworks. The CT520 uses a modified Wireless driver for WiFi NICs based on the Atheros chipset. It cansupport up to 32 Virtual Stations. Each of the Virtual Stations has its own IP address, IP port space, MACaddress and routing table. The Virtual Stations can be assigned to communicate to a particular AccessPoint, use a particular SSID, and have a WEP (64 or 128bit) or WPA/WPA2 key assigned. More advanced802.1X authentication is also included. There is a single WiFi radio per CT520 but multiple LANforgesystems can be clustered together for more realistic radio interference patterns and increased trafficgeneration capability. The radio supports 802.11 a, b, g or n mode. Transmit power andchannel/frequency is configured on a per-radio basis. Most other settings are configurable per virtualstation
-
product
Pulsed Transmitter
Built to operate in harsh environments, the Pulsed Transmitter unit provides radar installation decoy protection in a compact footprint and is powered by a Dewey Generator.The unit is comprised of a power supply, power amplifier, signal generator and antenna, with a fiber optic command and control interface providing throughput speeds capable of 1.25 G bits/sec via 1310 nm, single mode, ruggedized fiber.
-
product
3U VPX 1 Slot P&G w VITA 67.3C connector in J2
101V301P04-9003
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
product
Accelerometers
353B15
Sensitivity: (10 %);10 mV/g 1.02 mV/(m/s) Measurement Range:500 g pk 4905 m/s pk Frequency Range:(5 %)1 to 10000 Hz1 to 10000 Hz Frequency Range:(10 %)0.7 to 18000 Hz 0.7 to 18000 Hz Frequency Range: (3 dB)0.35 to 30000 Hz0.35 to 30000 Hz Resonant Frequency:70 kHz,70 kHz Broadband Resolution (1)0.005 g rms0.05 m/s rmsNon-Linearity:1 %1 % Transverse Sensitivity:5 %5 %
-
product
Micropower, 3-Axis, ±200 g Digital Output, MEMS
ADXL372
The ADXL372 is an ultralow power, 3-axis, ±200 g MEMS accelerometer that consumes 22 μA at a 3200 Hz output data rate (ODR). The ADXL372 does not power cycle its front end to achieve its low power operation and therefore does not run the risk of aliasing the output of the sensor. In addition to its ultralow power consumption, the ADXL372 has many features to enable impact detection while providing system level power reduction. The device includes a deep multimode output first in, first out (FIFO), several activity detection modes, and a method for capturing only the peak acceleration of over threshold events. Applications: Impact and shock detection. Asset health assessment. Portable Internet of Things (IoT) edge nodes. Concussion and head trauma detection.
