Probing
See Also: Probers, Probing Stations, Nano Probes
-
Product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-1Z1-6
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
4-Channel Broadcast Monitor
-
The COMM-connect Entry Level Broadcast Power Monitor type 3025 can control two external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. Equipped with the RMS Probes the Power conversion algorithms handles multi carrier, multi mode signals. With the 3026 Diode base probe the power readout gives good repeatable results. The power readout is auto scaled and VSWR will be calculated between the two probes. The COMM-connect Entry Level Power Monitor gives a number of application to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
Product
Premium 4.49 (127.00) - 12.00 (340.00) High Performance Lead Free Probe
LFRE-25L18-12
ICT/FCT Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Chemitec Sensors And Analyzers To Monitor Oxidants In Water
-
Chemitec's S494 series of amperometric probes provide continuous, accurate monitoring of chlorine and other oxidants in clean water applications. A range of sensors assures accurate measurement of oxidation, with sensors optimized for Chlorine (total, organic or inorganic), Chlorine Dioxide, Ozone, Peracetic Acid, Hydrogen Peroxide, Bromine, or Chlorites.
-
Product
K Thermocouple Magnetic Contact Probe
TP757
-
Magnetic thermocouple type “K” probe for measurements on magnetic metal surfaces.
-
Product
1 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1000
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1000 is ideal for 200–600 MHz oscilloscopes.
-
Product
Systems for Pipe Location
-
Here you will find an overview of SEWERIN cable location systems. Starting with locating technology such as fiber optic probes for locating non-metallic pipes, a system for acoustic locating of plastic pipes, to a multi-channel receiver for the localisation of water or gas pipes, telecommunications or power cables and other live or metallic supply lines.
-
Product
AC Current Probe 10 mV/A, 600A, 12 Hz LF Bandwidth, 30MHz HF Bandwidth, 1m cable
T3RC0600-HF
-
AC Current Probe 10 mV/A, 600A, 12 Hz LF Bandwidth, 30MHz HF Bandwidth, 1m cable.
-
Product
Retractable Cable
3700
-
Peaceful Thriving Enterprise Co Ltd
*2 x 6m retractable test leads.*Used as an extension cord for cars, trailers, boats and more.*Optional accessory included alligator clips, test probes and banana plugs.*The tester can be used with any multi meter or device equipped with banana jack connectors.
-
Product
Universal CMM Software Module
Verisurf CMM
-
Plug and play CMM communication for Hexagon Dea, Leitz, Mitutoyo, Wenzel, Pantec, Nikon, LK or Zeiss™️ machine controllers, as well as Renishaw, Tesa, Hexagon Leitz or Zeiss™️ head controllers.Optional support for scanning probes and error mapping compensation for geometric, volumetric, orientation, positioning and kinematic errors in the CMM structure that affects accuracy.
-
Product
Linear Testfixture (Cassette Not Included), UTT 586 x 248 mm
MG-03
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 248 mm (wxd• Outer dimensions: 750 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-1T-6
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
JTAG Debug Probe for Cortex-M
J-Trace PRO
-
SEGGER Microcontroller GmbH & Co. KG
J-Trace PRO for Cortex-M is setting a new standard for trace probes. It enables continuous streaming trace via its Gigabit Ethernet interface, lifting the limitations by internal buffers and slow data transmission.J-Trace PRO can capture omplete traces over long periods - thereby enabling the recording of infrequent, hard-to-reproduce bugs. This is particularly helpful when the program flow 'runs off the rails' and stops in a fault state. It also supports extended trace features, such as code coverage (so engineers have visibility of which parts of the application code have been executed) and execution profiling (providing visibility as to which instructions have been executed and how often - so hotspots can be addressed and optimization opportunities identified).
-
Product
Replacement Spade Terminals for High Voltage Differential Probe
PK-HVA-05
-
Replacement Spade Terminals for High Voltage Differential Probe
-
Product
Complete Graphical Power Quality Analysis System
PK5064-PRO+
-
The PK5064-PRO+ is the top choice for comprehensive power quality studies, energy audits, load studies, harmonic analysis, and more. Wide-range flexible current probes allow you to get into tight and confined spaces, wrap around large conductors, and measure almost any AC circuit that comes your way.
-
Product
High 1.73 (49.00) - 8.00 (227.00) High Performance Bias Ball Probe
POGO-1T1-8
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Temperature Logger for PT1000 Probe
TV-4204
-
PT1000 probes are available with this logger and will record down to -200C making them suitable for cryogenic applications. The probes are of 3-wire construction and available probes are listed in the 'You will also need' section.
-
Product
MANIFULATOR
-
As one of the most important module in Probe_Station, manipulator is an accurate system that probe micro distance() and contact on the electrode of semiconductor wafer, device. ECOPIA's Manipulator is very easy to use and probe arm's elastic plate is good to protect sample's surface, from being damaged by Z direction movement.
-
Product
Standard Type Spring Probes
-
From for bare board to for ICT, we have variety of spring probes for PCB. In addition to variety of tip type and total length, we also have receptacles that match the best to spring probes. We can also attach lead wire to the receptacles.
-
Product
Bandpass Filter/N
WFIL-B1893-1915F
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Power/Voltage Rail Probe, 2 GHz Bandwidth, 1.2x Attenuation, +/-60V Offset, +/-800mV
RP2060
-
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
Product
Microwave Testing
500B
-
The Model 500B Picoprobe sets new® standards in microwave probing performance. Benefiting from coaxial techniques, which have inherent low loss and low dispersion characteristics, the Model 500B Picoprobe achieves an insertion loss of less than 4.0 db and a return loss of greater than 15 db over its frequency range (see accompanying data).
-
Product
CAD / BOM Translation Software
ProntoTEST-FIXTURE
-
In minutes the Unisoft ProntoTEST-FIXTURE software translates CAD and Bill of Materials (BOM) files into real reference designators, netlists, X/Y component pin geometries, values, tolerances, part numbers, etc. This data is then used by Test Engineers to program their ATE (Agilent/Hewlett Packard "board & board x/y", Teradyne "ipl", Genrad ".ckt"), MDA, and flying probe test equipment and design the "Bed of Nails" test fixtures.
-
Product
Sampling Systems And Accessories
-
Parker's selection of sampling systems and accessories features fuel-drip bunker samplers; mini-sample cylinder valves; ultral-seal constant pressure cylinders for gas or liquid applications; single-flow, dual-flow and hot-tap probes; spun end sample cylinders for sample transportation; heated-enclosure systems for use with natural gas samplers; and composite gas samplers, among other solutions.
-
Product
Probe Station
DARK BOX
-
Size : 750 × 660 × 660 mm - Material : Steel - We can provide various dark box in size and shape at reasonable price as per customer requirements.And we also provide “integral sphere” with probe station as below.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR2270/71
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,13 kg
-
Product
Wafer/Chip/Package Semi-automated ESD Tester
400SW
-
Tokyo Electronics Trading Co., Ltd.
Semi-automated ESD tester featuring Ecdm 400E, Universal ESD Simulator. Used with a manual wafer probing system or a die manipulator, wafer or die level semi-auto ESD test can be done, as well as packaged device test. Damage is detected by V-I curve or leakage current change detection. Stress level and measurement points are programmed by personal computor via GP-IB. Once test terminals are selected, ESD endurance is automatically measured.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type I, Ø1.26mm, 305gf
K100-I126305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style I, Tip Diameter Ø1.26mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Transmission Probes
-
Transmission dip probes are used for on-line and inline absorbance measurements in fluids. When dipping or permanently mounting the probe end into the fluid, absorbance can be measured. Discover our range of various transmission dip probes below
-
Product
POWER PROBE 4 MASTER KIT
PPKIT04
-
*Combines the Power Probe 4, PPECT3000 and various accessories to provide the ultimate combination of diagnostic and circuit testing capabilities*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)*Tests fuel injectors, module drivers (transistors) and works as a circuit detector with the PPECT3000
