Voltage
The tension of an electromotive force.
-
product
14 Bit ADC Card
FMCADC100M14B4CHA
Sundance Multiprocessor Technology Ltd.
The FmcAdc100M14b4cha is a 4 channel 100MSPS 14 bit ADC card in FMC (FPGA Mezzanine Card) format. By default it uses only signals from the LPC rows of the HPC connector that is mounted. The gain can be set by software in three steps: +/-50mV, +/-0.5V, +/-5V. An advanced offset circuit is used in the front-end design of the ADC board, and allows a voltage shift in the range of +/- 5V that is independent on the chosen gain range.
-
product
Low Cost Precision Shunt
LPS
This is a precision metal clad resistor designed with four terminals. These models exhibit a high load capacity as well as excellent accuracy. The isolated voltage and current connections make them suitable for very precise current measurements. Direct attachment to current bus and connection to voltage using flexible wires enables easy current measurement.
-
product
PXI 2A Multiplexer, 2-Bank, 64-Channel 1-Pole
40-614-010
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
PXIe 2 A Relay Module, 80xSPST
42-139A-101
The 40-139A-101 (PXI) and 42-139A-101 (PXIe) are 80xSPST relay modules suitable for high density switching applications with medium power and feature 2 A current capacity with voltage rating to 300 VDC/250 VAC
-
product
Digital Multimeter
MDM-200 Series
The MDM-200 Series of instruments can measure parameters including AC/DC voltage, DC current, resistance, diodes, carry out on-off tests, zero-line judgement, non-contact voltage detection and the true effective value of AC. It is a tool with excellent performance; the ideal tool for laboratories, factories, radio enthusiasts and when carrying out home improvements.
-
product
Impulse Winding Tester
TH2883S8-5
Changzhou Tonghui Electronic Co., Ltd.
TH2883 series products are newly developed impulse winding testers by Tonghui. This product line makes Tonghui as the first provider of impulse winding tester from low voltage of 30V to high voltage of 10kV, single channel to multichannel (Max.:8 channels) in this industry. The instrument adopts popular 32 bit CPU and high density SMD technology, 65k color 7-inch TFT wide display screen, bringing ease for your eyes and convenience to your operation. The impulse voltage of100V~5000V, maximum 8 channel sweep test, maximum 20 test procedures, sampling rate of 200Msps, memory depth of 6k bytes makes your test accurately.The usage of standard sample average, application of demagnetized impulse, high bandwidth analog acquisition circuit, technology of high-fidelity corona extraction as well as the opening of non-destructive test reflect the design philosophy “customer-oriented, share the future technology with you” of Tonghui.
-
product
MARATON Moderate HE
MARATON is a family of MAgnetic field and RAdiation TOleraNt power supplies developed for CERN LHC. MARATON MHE represents a 12 channel low-voltage power supply for installation in a moderate hostile environment with integrated CANbus remote monitoring and control interface. Voltages, currents, temperatures and output power are controlled by the internal processor and illegal modes as well as failure will be detected.
-
product
DC-Powered, AC Voltage Monitor
VAD/VQD
NAI’s VAD and VQD are DC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
product
Three Phase Secondary Current Injection Test Set
TEST-330B
Beijing GFUVE Electronics Co.,Ltd.
Three phase secondary current injection test set is testing relay set, protective device, instruments, output ac dc current and voltage source, embedded Window XP system.
-
product
VLF test system
BAUR PHG 80 portable
BAUR Prüf- und Messtechnik GmbH
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
product
Battery Test Software
Landt Battery Test Systems use different programs for data acquiring and data process. The acquiring software comes with a very user-friendly interface, which allows new users to operate with minimal training. Data process software shows different kinds of plots (Voltage vs. Capacity, Capacity vs. Cycle Number, Efficiency, etc.), which can be easily exported.
-
product
Phase ID Systems
LED Meter Probe allows the user to take Real time Phase Angle readings along with AC nominal voltage readings. A PD800W LED Meter Probe works in conjunction with the Receive Unit to verify phase identification along with the actual phase angle data. This is all done without any calculations or data transfer from the field to a base computer. The meter probe and reference probe or receive unit can operate at 100 feet of separation and up to 300 feet line of sight separation. In the event that this distance would need to be greater, the Receive Unit can be unplugged from the charging cable and taken into the field while operating on it's rechargeable batteries for up to 8 hours at a time.
-
product
Digital (1kV below) Insulation Tester
1651 IN
Standard Electric Works Co., Ltd
Microprocessor-controlled. ACV auto-detection function on 3 insulation ranges (250/500/1000V) and low Ω ragne before pressing the TEST button. 68 x 34mm large LCD display. 3½ digital LCD (2000 counts) a LCD indicated instrument for insulation(MΩ), continuity (Ω) and AC voltage. Three insulation test voltages(DC V) : 250V, 500V, 1000V. Auto ranging. Auto power off function. Auto data hold function. Rel function (ohm only). Continuity buzzer. External AC voltage warning. Automatic circuit discharge. BS 16th edition.
-
product
Digital Meter
Shijiazhuang Suin Instruments Co., Ltd.
A meter is any device that measures and may record an electrical or magnetic quantity, such as voltage or current.
-
product
Analogue (1kV below) Insulation Tester
1126 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Measures insulation(MΩ) and AC voltage.● LED indiction for testing insulation.● Highly efficiency and accurate DC-DC converter.● Battery check function.● Compact and lightweight.● AC voltage measurement can be made without depressing the test button.
-
product
High Frequency Current Transformer
HFCT Ø 140mm
Techimp Clamp High Frequency Current Transformer model 140 is an inductive sensor for partial discharge measurements. It is suitable for online /off line PD tests on : large diameter cables ; grounding rod bar ; etc. A TNC termination is available to connect the Clamp HFCT 140 to the TechImp PD analyzer : PDCheck , PDBase etc. The arrow indicates the requested input current (Iin) direction to get coherent output voltage (Vout) polarity respect to ground. When the sensor is installed with the arrow directed to ground, the detected voltage signal (Vout) has the same phase of the input current (Iin).
-
product
Impulse-Calibration-System
KAL1000 Series
The impulse calibration system KAL1000 is a modular system to perform tests on complete impulse voltage measuring systems and on digital recorders for the measurement of high impulse voltages and impulse currents. The modular design allows an optimal KAL-configuration depending on the actual application.Additional, this modularity allows to up-grade or modify and existing KAL1000 system in case of changing or additional requirements
-
product
Bench/System Precision Linear Regulated DC Power Supply With Digital Control, Single Or Triple Outputs, 105 To 242 Watts, With/without Remote Interfaces
QL Series II
Advanced dc power supplies, single or triple outputUp to 112 watts per outputVery high precision, very low noise, excellent dynamicsAdvanced user interface with numeric and rotary controlMultiple voltage/current ranges for increased flexibilityMultiple non-volatile memories for power supply set-upsSwitchable remote sense provides perfect load regulationComprehensive protection including OVP and OCP tripsCompact bench footprint; modular width for rack mountingAuxiliary output fully variable 1.00V to 6.00V at 3A with selectable voltage and current metering (T models)Bus programmable via USB, RS232, GPIB or LAN (P models)LAN interface is LXI compliantDuplicate power and sense terminals at rear (P models)
-
product
Reference plus Comparator or Amplifier
Analog Devices reference plus comparator or amplifier products combine the excellent initial accuracy and low overtemperature drift performance of single function voltage references with comparators, buffer amplifiers, and current sense amplifiers. These products offer compact solutions for a broad range of applications such as battery monitoring, threshold detectors, window comparators, auto power-off circuits, and low dropout (LDO) regulators.
-
product
96-Pin SCSI Micro-D Straight PCB
40-963-096-SM
Ideal for user created termination schemes where the termination is to be on the front of the product or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
LED synchroscope
LS-110 SYNC (110V, 120V, 220V, 230V, 240V)
Standard Electric Works Co., Ltd
• Input Voltage : 110V AC, 120V AC, 220V AC, 230V AC or 240V AC.• Standard 4.5-inch switchboard case.• Front panel mount.• 3 bi-colored LED indicators for "SYNC", "GEN" and "BUS".• 24 LEDs in a circle display the phase angle and the frequency differences between 2 networks.• 360° LED indication.• 12 o'clock position LED is bi-colored.
-
product
DC Blocking L-Band Splitter Combiner
PD5920
INSTOCK Wireless Components, Inc
PD5920 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other port blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5920 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 2 way power divider input rating tables for additional power handling info.
-
product
LXI WTB Adaptor, Terminated
60-982-002
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
product
PXI 2 Amp Multiplexer, Dual 8-Channel, 4-Pole
40-635A-007
The 40-635A-007 is a dual 8-channel, 4-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
3 In 1 Metal Voltage Stud Detector
NT-6352
Combined unit to accurately detect live or dead electricity cables, water or gas pipes and wooden studs or battens.LED & buzzer indicators.Depth penetration 18~20mm.Using precision screwdriver for easy unit sensitivity adjustment.Power source: NEDA1604/6F22 (9V) x 1pcs(Not included).Size: 178 x 120 x 34.7mm.
-
product
Voltage Converters
Made from marine-grade aluminium extrusions or heavy-gauge aluminium sheet metal. Powder-coated or anodized, and use stainless fittings throughout Fitted with robust circuit boards using expensive heavy-gauge copper conductors, designed by Analytic Systems' engineers and assembled in our plant.Models are available to step-up, step-down, stabilize or isolate DC power over a range of 12 to 360 volts. No matter which unit you need, these easy-to-install Voltage Converters will give you many years of reliability.
-
product
AC Power Supplies
BLC Series
The BLC Series delivers all the quality features our customers have come to expect from Behlman; clean sine wave output with excellent line and load regulation, high efficiency and low harmonic distortion. A multi-pulse input transformer offers low-input harmonic distortion and high power factor as required by European standards. Unique protection circuitry provides for over-temperature protection; short-circuit protection and voltage fold-back during overloads to maintain undistorted waveforms.
-
product
Turns Ratio Meter 3 Phase
TR-MARK III 250V
The TR-MARK III 250V is the successor of the famous TR-MARK III. Besides an extended test voltage up to 250V, it offers new features and increased accuracy to make it a perfect system. A color LCD with back lighting and touch screen increases handling and user comfort. Two USB interfaces make it easy to store measurements on external storage devices and transfer easily to a personal computer or download nameplate data of transformer to test.
-
product
PXI Hex 4:1 High Voltage Power MUX
40-331-004
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
product
High Performance Power Analyzer
AFM-8A
AFM-8A has Developed for AFC*(Auto Frequency Control) high performance measurement and frequency update, its update up quickeer than 100mSec. multifunction power analyzer provides high-accuracy measurement and is designed for single phase and three phase application. It includes 4 Digital inputs, 4 Relay outputs, and a RS-485 Modbus RTU Communication port. The user can choose one more communication port, and 2 Analog outputs for output expansion.It provides measure voltage and current of the 2~63 harmonic, and it shows CO2 emissions, which is suitable for power monitoring, management and analyze power quality. It has TOU (time-of-use) function and 4MB Flash memory capacity, allowing users to record data for a long time. It also has a software line adjustment function to reduce the on-site line adjustment work.It has the functions of waveform capture and recording, power record, and event record, which can be used for multifunction power analyzer.
