Test Fixtures
UUT interconnect interchangeable with tester.
See Also: Fixtures, Mechanical Fixtures, Vacuum Fixtures, ATE Fixtures, PCB Test Fixtures, Board Test Fixtures, Bed of Nails, Spring Probes, Test Jigs, Test Probes
-
Product
One Port Vector Network Analyser
TE3001
-
The TE3001 One Port Vector Network Analyser is built for the professional who understands the calibration process and has a network analysis task to perform. The unit features a larger output signal than the TE3000 for better noise immunity, and is supplied with a 6 piece custom calibration kit to remove the effect of test fixtures and cables. Together, these features make the TE3001 ideal for broadcast and plasma applications that require a length of cable for connection and may be high in noise or interference.
-
Product
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block
780041-01
-
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
Product
PXI 12x8 RF Matrix 250MHz 75 SMB - With Loop-Thru
40-726A-751-L
-
The 40-726A is a 12x8 RF Matrix Module suitable for switching frequencies up to 300MHz (50Ω version). The 40-726A is available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The module is designed to provide a simple and scalable bidirectional matrix for RF frequencies. Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
Product
SATA
-
SCHILLER AUTOMATION GmbH & Co. KG
SATA test adapters and test fixture kits facilitate Source and Sink compliance testing.
-
Product
In-Line / Board Handler
-
Circuit Check’s in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading ICT handlers including Keysight 5i, Teradyne TSh Multi-Site, IPTE and Pematech. Circuit Check is the go-to partner for in-line functional test fixtures to speed production throughput.
-
Product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
-
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
Product
DC Current Bias Supply
DC1000A
-
To guarantee the quality and performance of inductive components such as inductors, chokes and transformers they are tested at their real-life operating point. If the inductor is designed to carry a DC current, then its inductance must be measured with that DC current present. Until now, these measurements were made by an LCR meter connected via special interfacing to a DC bias supply available only from the manufacturer of the LCR meter. The unique NEW DC1000A can be used with any precision LCR meter and connects simply into existing test fixturing.
-
Product
PCI RF Switch Cards
-
These 8x9 RF Switch Cards are suitable for switching frequencies up to 500MHz. Available in either 50 or 75 versions with SMB coaxial connectors. These switch cards are intended for the easy construction of high-performance bidirectional matrix switching systems. Automatic isolation switches are located on all coaxial connections, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/7
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,30 kg
-
Product
Computer Networking Solutions
-
Today’s world has a never ending appetite for data. Everywhere you look there are connected devices that provide and consume that data at an astonishing rate, and the demand increases every day. Our computer and networking customers are constantly pushing the edges of technology to deliver data faster and more reliably than ever. They use the newest electronics available to keep our data flowing – data that is critical to the operation of the world’s infrastructure. As cutting edge technologies are developed, these faster more advanced capabilities require the most sophisticated testing available. Circuit Check is constantly evolving our test fixtures and systems to meet this industry’s most advancedrequirements.
-
Product
Fixture Building Software
FixGenius
-
Tests show that FixGenius’ rule-based probe-mapping algorithms reduce pin deflection by up to 25% compared with traditional fixturing packages. FixGenius comes with a powerful Fixture Editor that allows the user to change the probe mapping. If a solution is mathematically possible, FixGenius’ algorithms will find it, and pick the one with least deflection. If the job simply cannot be done with one single fixture, FixGenius will fully automatically split the test into multiple fixtures or into fixture and flying probe test sets, with guaranteed test integrity.
-
Product
Functional Test Fixtures
-
RNS can build almost any test equipment and automated test machinery. We have delivered soltions for HiPot, LED Test, Leak Test and RF shielded applications for years. We can provide Complete Test Systems, including Test Fixtures, Rack System and even Programming. Our team is committed and has a proven track record of delivering exceptional products independent of scope, so simple- and high-complexity projects are handled with equal care.
-
Product
PCB Test Fixtures
-
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Product
System Level Test and Burn-in Solutions
-
System Level Test (SLT) is a paradigm shift from traditional structural and functional testing. The device is tested in a complete, integrated system to evaluate its compliance against specified requirements. The system approach allows for higher and more cost-effective test coverage especially for multi-function and non-deterministic devices. It also brings new integration and test challenges like: ..Designing test fixtures on Burn-in Boards with system components ...
-
Product
Low Noise Test Cables For N1413 With B2980 Series, 3m
N1427B
-
The N1427B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1427B to the B2985B/87B.
-
Product
Power Cord Bending Tester
SW-6
-
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
Product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
-
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Manual Test Fixture (MA)
MA 2013/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 25,00 kg
-
Product
Cost-Effective ATE System
PRO RACK ATE
-
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
Product
Functional Test Fixtures
-
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
Product
Small Footprint Flex 20 ATE
Flex 20
-
The Flex 20 is floor mounted but maintains a small footprint on the shop floor. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
Product
CAD / BOM Translation Software
ProntoTEST-FIXTURE
-
In minutes the Unisoft ProntoTEST-FIXTURE software translates CAD and Bill of Materials (BOM) files into real reference designators, netlists, X/Y component pin geometries, values, tolerances, part numbers, etc. This data is then used by Test Engineers to program their ATE (Agilent/Hewlett Packard "board & board x/y", Teradyne "ipl", Genrad ".ckt"), MDA, and flying probe test equipment and design the "Bed of Nails" test fixtures.
-
Product
Test Fixture
N1295A
-
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
Product
Shielding Effectiveness
-
Radiometrics Midwest Corporation
One of the more difficult tests to understand is shielding effectiveness or transfer impedance. The data from these tests may vary dramatically based on the test method selected, test fixture, test setup, measurement sensitivity, test personnel, etc. At Radiometrics all shielding effectiveness test are performed or supervised by NARTE Certified engineers.
-
Product
Custom Test Fixtures
-
Intrinsic Quality is proud to offer a variety of Test Fixture Development Services that include fixture building, tester interface building, harness building, troubleshooting, maintenance, design, and engineering. IQ’s fixtures are built to exacting specifications and configured to deliver quality production testing. Our global customers have trusted us for over 35 years to provide custom solutions applying leading edge technology. IQ consistently delivers cost-effective solutions with our client’s recognition and gratitude.
-
Product
Non-Destructive Resonant Inspection Drop Test Fixture
RAM-DROP
-
The Drop Test Fixture, Model RAM-DROP, Resonant Inspection System, allows automated sorting and quality testing of small metal injection molded (MIM), powder injection molded (PIM), additively manufactured, and other small parts by using the Resonant Acoustic Method (NDT-RAM).
-
Product
PXI 22-Channel 2A Fault Insert Switches
40-202-001
-
This is the 22 Channel version of the 40-202 Fault Insertion Switch. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test.
-
Product
Hand Held Test Fixtures
-
Manual, or semi-automated mechanical devices designed to secure a Device Under Test (DUT) and provide a stable interface for electrical testing, inspection, or programming.
-
Product
Test Adapters
-
In our specially developed MG range of linear test adapters (test fixtures), we use solid aluminium components in our mechanical construction. This is to ensure the reliability and contact accuracy of the test adapter.
-
Product
Universal Breakout Test Fixture
CA-323
-
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
