Verifiers
-
Product
Optical Channel Monitors
-
DiCon's Optical Channel Monitor is an advancedoptical subsystem, with integrated tunable optical filter, that automatically scans a DWDM network and reports the power of each channel. Network performance is monitored and reported in real time. Feedback from the Optical Channel Monitor can be used to optimize optical power levels, identify performance drift, and verify system functionality. An optional integrated optical switch allows up to 12 separate input ports to be monitored sequentially.
-
Product
1229a Frequency Generator
-
Precise Time and Frequency, Inc.
The ptf 1229A utilizes the latest technological advances in precision frequency synthesizers to provide a multiple output, wide range, high precision frequency reference instrument, capable of delivering frequencies over the range of 0.1Hz up to 30MHz with a resolution of 0.1 Hz over the full range.The unit includes an external reference input to allow extremely high accuracy outputs at precisely the frequency required, together with a front panel indicator to verify “lock” to the external reference. The standard unit includes two independent frequency outputs of any frequency within the range, and provides both sine and square wave outputs for each frequency.An expansion module gives the capability to increase the number of independent frequency outputs up to a total of four frequencies, with sine and square wave outputs for each, giving a total of eight outputs.
-
Product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
GENEM-C 100G Ethernet/IP Infrastructure Test Application
-
GENEM-C is a high-capacity network infrastructure testing software application for network equipment manufacturers, data centers, service provider telco cloud and 5G backhaul. It runs on the PROVA-C hardware appliance that is built on BittWare. GENEM-C allows you to verify, monitor and troubleshoot Ethernet/IP network equipment and data center applications to ensure network services can accommodate the demands of your customers. Ideal for QA test, Service Providers migrating to a DevOps model can use GENEM to validate service turn-up and modifications in the production network. GENEM is equally at home in a lab environment. It bundles wire-rate traffic generation and analysis capabilities with a network emulator and packet capture/replay function in a single software license.
-
Product
Action Counter Tester
-
Weshine Electric Manufacturing Co., Ltd
Lightning strike counters of lighting arrester measure lightning strikes by the induction of current and do not require the use of any external power source. Weshine invented Lightning-strike-counter Tester (VS-451) is used of verify that if strike counter is correctly mounted and connected. As well as output current with sensitivity of 0.01 mA to correct leakage ammeter.
-
Product
MPO Visual Cable Verifier Kit
KI-TK832
-
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end.
-
Product
Air Data Computer (ADC) Tester
MS 1122
-
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
Product
Hardy Shaker
HI-913
-
This Hardy Shaker provides the ability to set the amplitude and change the frequency range without the amplitude changing. This automation makes conducting a test easier. A test can be conducted on a vibration transducer and manually recorded. Multiple tests are not saved; for multiple tests use the HI-903 or HI-803 units. The HI-913 is used for testing from 7 to 10,000 Hz, it offers adjustable frequency and vibration levels. This provides a reference source for verifying the accuracy of vibration transducers, connectors, cabling and instruments or instrumentation systems. The HI-913 has a ruggedized suspension system that can support heavy transducers (up to 800 grams - see frequency limits in the manual). The HI-913 has a built-in battery charger that can operate on 120 or 240 VAC. The unit comes in a rugged Pelican case.
-
Product
Handheld Network Coverage Verification Tool
Nemo IoT Meter
-
An easy-to-use handheld NB-IoT and LTE-M network coverage verification tool. Nemo IoT Meter is an easy-to-use handheld measurement tool for verifying IoT service quality at customer premises. Nemo IoT Meter can be used in industrial environments to verify coverage and end-to-end connection quality for IoT device installations. Ideal for technicians installing IoT probes and sensors, it runs on a regular Android-based smartphone and is connected through an NB-IoT or LTE-M dongle.
-
Product
Network Simulation and Load Testing
-
EXFO offers a complete range of high-performance test solutions, covering the entire converged network from RAN to IMS. By mimicking real-world customer behavior in lab environments, our solutions allow mobile operators and equipment manufacturers to verify their wireless networks before deployment.
-
Product
Verifier Computer Interface Report
VCIR
-
The Verifier Computer Interface Report (VCIR) is a Windows software package that allows for transferring inspection report from your Inspector series bar code verifier to a computer. Once transferred you can review the ISO/ANSI inspection results or view the scan reflectance profile for detailed troubleshooting. The inspection results can be saved by job for later retrieval or to append new inspection results to the existing job. As each job is saved an Excel spreadsheet (CSV file) is generated. You can customize which parameters should be saved in the spreadsheet. The spreadsheet provides a simple report that will have a line for each bar code inspected.
-
Product
VIS-NIR Cameras
-
Surveillance cameras based on CCD/CMOS/ ICCD/ EMCCD/EBAPS imaging sensors sensitive in visible and near infrared range are widely used in many long range surveillance applications as independent imagers or as part of a bigger multi-sensor surveillance systems. Majority of VIS-NIR cameras are used for day level applications but an increasing number of these cameras is used to enable surveillance in both night and day conditions. In both cases it is important to verify performance of these cameras under varying illumination conditions from very dark nights to ultra bright days. Important missions can fail due to too low sensitivity of VIS-NIR cameras at night conditions (dark, noisy images) or due to too low dynamic at ultra bright day conditions (saturated, blurred images). Next, it is important to use VIS-NIR cameras that generate high quality images in order to achieve maximal effective surveillance ranges.
-
Product
Battery Discharge Capacity Tester
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 1.02k Ohm
50-293-021
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Personal SerDes Testers
C Series
-
Everything you need to develop and verify your high-speed digital algorithms is contained in these ultra-portable test instruments. They will forever change the way you think about developing and verifying Gbps digital and mixed-signal algorithms, and they will allow you to measure signals in ways that were not possible in the past. Each personalized SerDes tester is equivalent to multiple hardware platforms, containing everything that you need to make high-performance measurements like bit error rate testing, signal generation, and signal measurement.
-
Product
JTAG Test Procedures
-
Corelis will process your design information, create all necessary test vectors, and verify the test vectors using your actual hardware. This is a complete “turn-key” service resulting in a fully verified and debugged boundary-scan test system. For companies short of resources, those who are under a tight deadline, or for those who are new to boundary-scan and want to be testing in the shortest time possible, this is an excellent way to minimize your investment and maximize your effectiveness.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm
50-294-023
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
EasyColor
-
Fast conversion of images between 11 color spacesColor segmentation: to identify objects based on their colorColor verification: to verify the color of objects
-
Product
Universal In-System Programming Tool
ScanExpress JTAG Programmer
-
ScanExpress JTAG Programmer is a universal in-system programming (ISP) solution designed for convenience and versatility—a modular, multi-functional, and high-performance tool to program, read, and verify Flash memories, serial EEPROMs, CPLDS, FPGAs, and more.Like all Corelis ScanExpress family products, ScanExpress Programmer is a tool for all phases of the product life cycle—whether programming early code during product development, programming production code during manufacturing, or reprogramming units out in the field, ScanExpress Programmer is designed to fit all in-system-programming needs.
-
Product
Burn-in Board Continuity Tester
CT-1
-
Burn-in Board Coninuity Tester. Verifies burn-in board continuity and component tolerances. 768 I/O channels, can be forced to the constant current source or grounded independently. Highly accurate measurement of resistance, voltage, and capacitance using a pair of precision instrumentation amplifiers.
-
Product
CE Marking
-
The CE mark enables the free movement of products into and within the European market.By placing a CE mark on a product the manufacturer is declaring, on their sole responsibility, that the product conforms to all legal requirements to achieve CE marking.Prior to placing the product on the European market, a manufacturer performs an assessment of the product against all applicable EU Directives, and verifies compliance with the relevant essential requirements.Not all products require the CE mark – only products subject to specific directives must bear the CE mark.
-
Product
SoC Verification
TrekSoC
-
TrekSoC automatically generates self-verifying C test cases to run on the embedded processors in SoCs. This verifies your chips more quickly and more thoroughly than an external testbench, hand-written C tests, or running only production code on the processors. TrekSoC's generated test cases target all aspects of full-SoC verification and work in a variety of different environments.
-
Product
Concrete Hardness Tester
W-M-250
-
The W-M-250 Manual Test Hammer is the traditional instrument used for the non-destructive testing of hardened concrete. This easy-to-use instrument provides a quick and simple test for obtaining an immediate indication of concrete strength in various parts of a structure. The minimum verifiable strength is 1400 PSI (10 MPa)
-
Product
Cable TV
-
Tempo Communications provides technicians with an array of test and measurement solutions to optimiz... e the installation and performance of broadband cable networks. The tried-and-true TDR from Tempo delivers all of the enhanced features required to pinpoint faults and verify performance. Like all of its test and measurement devices, the focus is on reliability, ease-of-use, and quality—empowering technicians to do their jobs and exceed customer expectations.Show less
-
Product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
Chained Data Test Support for 802.3at and 802.3bt PSE's
-
Intuitive graphical user interface. Configures up to 24 2-Pair or 4-Pair ports for "snaked data path" testing. Verifies all PSE connections in the defined data path. Sequences user-defined PD emulations and PSE powering.Verifies powering to user-defined loading on all selected ports. Configures looped data paths across the selected ports. Support of 802.3at / 802.3bt LLDP power negotiations (PSL-3424L).
-
Product
DOI / Haze Meter
807
-
TRICOR’s Hazer Meter and DOI is ideally suited for measuring flat, non-textured high reflectance surfaces. The Model 807A Haze Meter design is in accordance with ASTM E430 and ASTM D5767 (method A) and is used to measure ±3 degrees around the specular lobe centered at 30 degrees in approximately 220 increments. That’s an angular sample size of 1 sample per 1.6 minutes of arc! This allows differentiation between samples with very small differences in reflectance characteristics. Verified replacement for the older Hunter Dorigon II haze meter unit.
-
Product
Oil Test Equipment
-
KV Hipot Power Test Equipment Co.,Ltd
oil analysis program is to verify that a lubricated machine is operating according to expectations. When an abnormal condition or parameter is identified through oil analysis, immediate actions can be taken to correct the root cause or to mitigate a developing failure.
-
Product
High Accuracy In-Situ Mass Flow Verifier
HA-MFV
-
The HA-MFV, High Accuracy Mass Flow Verifier is designed for use on process tools to verify mass flow control flow rates in-situ. Available with EtherCAT® or DeviceNet™ communications and measurement accuracy of 1.0% of reading, the HA-MFV can verify MFC flow with the actual process gas significantly better than older rate-of-rise devices or process chamber rate-of rise methods.
-
Product
ENA Vector Network Analyzer
E5080A
Vector Network Analyzer
9 kHz to 4.5/6.5/9 GHz, 2- or 4- port, 50 ohmWide dynamic range 152 dB (typical)Fast measurement speed 3 ms (401 points)Low trace noise 0.0005 dBrms (typical)High temperature stability 0.005 dB/CWide source power range 90 to +15 dBm (spec)Intuitive touch-based GUI on large, high-resolution 12.1" screenE5071C/8753 code compatibility Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm
40-294-011
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
