Test Cards
See Also: Cards, Extender Cards, Probe Cards, POST Cards
-
product
Communications Test System for Frontline Diagnostics
ATS3000P
The ATS3000P is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000P also includes the sophisticated IF and baseband I/Q DigitalSignal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easyto-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets are available for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
-
product
Linear Array Detector Cards
X-Card 0.2 to 2.5mm
A product family of high performance linear X-ray detector cards with preamplifier ASICs. The preamplifier ASIC converts the charge output from the photodiode array into voltage with serial output for easy integration with readout electronics. Can be arranged end-to-end to form large linear detector arrays.
-
product
In-Circuit Testing and Test Engineering
GenRad 2287
3560 Hybrid Test NodesWindows InterfaceTotal GenRad 227X Migration Capability20 Mhz Clock, Sync, and Trigger, 5 Mhz data ratesVector Test for VLSI, PLCC’s & ASICSTest Express Vectorless TestingMultiple Chain Boundary ScanAnalog Functional Test Module
-
-
product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
-
product
XMC Processor Cards
Curtiss-Wright Defense Solutions
Our XMC mezzanine cards provide an easy way to add processing power and meet performance requirements within the most demanding size, weight, and power (SWaP) constraints. Create a zero-slot solution by mounting the mezzanine on a graphics or FPGA card or on the power supply of a Curtiss-Wright 3U or 6U computing system.
-
product
Dual Channel Clock Driver Card
PI-41400
The PI-41400 is a dual channel Clock Driver card capable of operating up to 190 MHz into a 50-ohm load and up to 80 MHz at an amplitude of 8 volts into a 1-megohm load. Into a high impedance load the output voltage range is from a –3 volts to 8 volts with the output pulse amplitude ranging from 0.5 V to 9 V. When driving a 50 load the voltage range is –1.5 volts to 4.5 volts with the output pulse amplitude ranging from 0.25 V to 4.5 V. The rise and fall times of the output pulse are variable from 1.2 ns to 9 ns into a 50-ohm load and <5 ns to 9 ns into a HiZ load. The output pulse amplitude and the load being driven determine the range of variability. The driver output can be set for tri-state operation and the output polarity can be set for ‘Normal’ or ‘Inverted’ operation through software.
-
product
6U Horizontal Card
2270
VECTOR Electronics and Technology, Inc.
Versatile chassis for horizontal card installation
-
product
Functional Test System Optimized For Real-Time Digital Bus Test
Spectrum HS
Spectrum HS is Teradyne’s fully integrated functional test system. Optimized for real-time test of low latency buses, it’s a high-performance system delivering excellent test coverage of current and future products.
-
product
SIMRC Card Carrier
1050-001
The SIM Relay Carrier 1050 simplifies the custom integration of small format embedded switching cards. No additional PCB design is necessary. Due to the Eurocard format the carrier can be fitted into a standard case or can be mounted in a 19" rack with side rails. Plug in standard SIM Relay Cards and control your switch application with the provided Soft Front Panel without any additional programming.
-
product
6TL22 Off-Line Testing Platform
H71002200
Learn about our Build to print service for Test Platforms. The 6TL22 Platform is a perfect base for the conception of a real modular Automatic Test Equipment for low to mid manufacturing volumes.A system designed around the 6TL22 is simple, easy to maintain and cost effective. The rack is prepared for the direct integration of the three platform based receivers from Virginia Panel, the S6, G12 and G12X.
-
product
Embedded MXM GPU Module with Embedded NVIDIA RTX™ A1000
EGX-MXM-A1000
- NVIDIA Ampere Architecture- Standard MXM 3.1 Type A (82 x 70 mm)- PCIe Gen 4 x8 interface- 2048 CUDA® cores, 16 RT Cores, and 64 Tensor Cores- 6.66TFLOPS peak FP32 performance- 4GB GDDR6 memory, 128-bit- 192GB/s maximal memory bandwidth- 5-year availability
-
product
Production Parametric Probe Card
VC20TM Fab
*Maximum channel count: 48*Tester platforms: Keysight 4062, 4072, 4080, Keithley S600, S530, Rack and Stack configurations.*Minimum Pad Size: 30ux30u (tunable scrub)*Contact Resistance: less than 1 ohm*Temperature range: -65C to 200C*Leakage: Less than 5 femto Amps per volt. If you require faster settling time*Repairable*Lifetime Performance: Production customers are experiencing 10M+ million touchdowns on Aluminum and Copper pads. Few to no rebuilds due to pobe wear
-
product
Multifunction Analog I/O Card
LPCI-AIO16A
Model LPCI-AIO16A provides 500k samples/second, with 16-bit resolution, for the board’s 16 single-ended or 8 differential analog input channels. Also included are two 12-bit analog outputs, 16 digital I/O lines and an 8254 with three 16-bit counter/timers. The board meets the MD2 Low Profile PCI Bus Specification and can be installed in any 3.3V or 5V PCI or PCI-X slot.
-
product
Matrix Card
MATX4010
The MATX4010 module is a general purpose-switching matrix, consisting of 40 relays arranged in 5 rows by 8 columns. Each row/column consists of independent Force/Sense lines that are switched simultaneously. Each relay is capable of handling 10 Amps and can isolate up to 5 KV. Each relay on the matrix is independently controlled with an On/Off command via software.
-
product
Controller Card
GPIB-PCI-XL
The GPIB-PCI-XL is a flexible PCI GPIB controller card that converts any PC with a PCI bus slot into a GPIB controller.
-
product
PCIe Card MX3 Copper Interface
OTP2 module no.183
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions.
-
product
FPGA Mezzanine Card
FMC407
The FMC407 is a low noise clock generation and distribution module with eight clock outputs and eight trigger outputs that are fully synchronized.There are two configurations: 34.375MHz-200MHz or 34.375MHz-4.4GHz. The FMC407 is ideal for applications that require synchronous A/D or D/A sampling across multiple cards or systems.
-
product
GPGPU Cards
Curtiss-Wright Defense Solutions
For applications requiring massive parallel compute capability, such as deep learning frameworks for AI applications, our highly engineered GPGPU co-processing engines provide a field-proven hardware foundation. Curtiss-Wright GPGPU co-processing engines leverage the latest NVIDIA Tensor Cores (for machine learning) technology and are a critical component of the high-performance embedded computing (HPEC) ecosystem that delivers data center capability at the tactical edge.
-
-
product
Extender Card
The IEEE extender card, referred to as board PWB1000281-03. Extender card to allow for testing and debugging of the chassis assembly. This board was originally an Intel design that Dynamic Engineering was authorized by Intel to re-create
-
product
Add-In Card
BrainChip Accelerator
BrainChip Accelerator is an 8-lane, PCI-Express add-in card that increases the speed and accuracy of the object recognition function of BrainChip Studio software by up to six times. It does this by accelerating video scaling, spike generation, and spiking neuron model comparisons. In combination with a CPU that has 16 virtual cores, BrainChip Accelerator can process 16 channels of video simultaneously, with an effective throughput of over 600 frames per second.
-
product
HPx-310 Radar Signal Output Card
The HPx-310 Radar Signal Output card is a replacement for the HPx-300, form, fit, and function. It generates representative radar signals for system testing, simulation, training or radar video streaming. Under software control, the card generates radar video, trigger and azimuth signals similar to those generated by real radars.
-
product
S_A_Relay Card
The Stand Alone Relay accepts a regular PC style power connector that powers two relays. Upon power failure, the relays disengage the two ethernet lines so as to not interrupt communication on the ethernet lines. A CPLD allows for pass through and bypass of Ethernet signals. 10/100 Ethernet compatible. The CPLD is controlled via user input.
-
product
General Purpose Switching PXI Card
GX6325
The GX6325 is 6U switching card with 75 SPDT Form C relays with a switching power rating of 60 W. Featuring the highest density available in PXI for this type of switch card, the GX6325 is suitable for all test applications requiring general purpose, low level switching.
-
product
VPX GPGPU Processor Card
VPX6-4942
Curtiss-Wright Defense Solutions
The rugged VPX3-4942 NVIDIA Tesla Maxwell-2 GPU processor is designed and manufactured by Wolf Advanced Technology. The board is part of a family of GPGPU modules available from Curtiss-Wright Defense Solutions to enable development of High Performance Embedded Computing (HPEC) systems.
-
product
Probe Cards
Ceramic Blades
SV TCL offers a variety of ceramic blades and blade probe cards. We have patented ceramic microstrip blade probes available in low leakage and low capacitance for optimal signal transference, while SV TCL's blade cards are ideal for parametric and RF testing.
-
product
Magnetic Material Test Fixture
16454A
The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.
